LG WD-1080FH Service Manual ▷ View online
40
① The hose clamps and the hose are disassembled.
② The ventilation bellows and the water inlet
bellows are disassembled on the tub.
DISPENSER ASSEMBLY
Valve (Hot)
DRAWER
DRAWER
① Disassemble the top plate assembly.
② Pull the drawer to arrow direction.
③ Two screws are unscrewed.
③ Two screws are unscrewed.
41
① Disconnect the wiring connector.
② Unscrew 2 screws from the back.
② Unscrew 2 screws from the back.
When reconnecting the connector
~WD-1223FH(B)/1225FH(B)/1243FH(B)
WD-1245FH(B)
/1041(3)FH(B)
WD-803(4)0(W)(F)H
WD-102(4)1(5)W(F)H/102(4)1(5)FH(B)
WD-1042FH(B)/803(4)0FH(B)
₩
① The back cover is removed.
② Unscrew 2 screws
③ Pull the PWB assembly (Main) as shown.
② Unscrew 2 screws
③ Pull the PWB assembly (Main) as shown.
1
2
3
INLET VALVE
PWB ASSEMBLY (MAIN)
VALVE#1 (MAIN)
White/Black - Black
VALVE#2 (PRE)
Gray/ White - Black
VALVE#3 (HOT)
Blue/Red-Black
■ WD-1223(5)F(H)(B) / WD-1243(5)F(H)(B)
WD-1041(3)F(H)B / WD-102(4)1(5)F(H)B
WD-803(4)0F(H)B
WD-803(4)0F(H)B
■ WD-803(4)0(W)(F)(H)/WD-102(4)1(5)W(F)(H)
WD-1042F(H)
42
Open the lower cover cap by using coin and remove
the lower cover to arrow direction after screw is
unscrewed.
※ When the power cord is plugged, the door can
be opened by pressing the DOOR OPEN
( ) button.
① Open the door completely.
② Remove the two screws from the hinge.
② Remove the two screws from the hinge.
① When you can not the door with the front door button
(i.e. power failure) there is an emergency opener on
your machine.
your machine.
② To reach this opener you have to open the lower cover
cap and pull the opener to open the front door.
① Rotate the drain plug (remaining hose) to arrow
direction.
② Pull it out from hose.
※ First, prepare a bucket to put in the remained water
※ First, prepare a bucket to put in the remained water
Opener, Door
STRAP
Cap
(Remaining Hose)
LOWER COVER
DOOR
Opening the door in emergency
Removing method of remained water
ATTENTION!
Do not use this emergency opener during wash.
Do not use this emergency opener during wash.
43
① The cabinet gasket clamp is released.
② Two screws are unscrewed from the cabinet cover.
② Two screws are unscrewed from the cabinet cover.
① Three screws are unscrewed from the lower cover.
② The lower cover is disassembled.
② The lower cover is disassembled.
① The control panel is removed.
② Screw is unscrewed from the cabinet cover.
② Screw is unscrewed from the cabinet cover.
① Take apart the tub gasket clamp
② Make sure that the drain hole of the gasket is put
② Make sure that the drain hole of the gasket is put
beneath when reassembling the gasket.
※Refer to the arrow mark on the tub cover.
GASKET ASSEMBLY
Click on the first or last page to see other WD-1080FH service manuals if exist.