LG WD-10660N Service Manual ▷ View online
20
YES
YES
YES
NO
NO
NO
NO
NO
YES
YES
YES
YES
Wiring diagram
option (HOT)
MAX
max
ABNORMAL SOUND
SOFTENER DOES NOT FLOW IN
Fix the bolt tightly.
Replace the V-belt
(4400FR3116B)
(4400FR3116B)
Replace the motor.
Refer to
NO WATER SUPPLY
Check the wiring on the
dispenser.
dispenser.
Put it in the correct
compartment.
compartment.
Clean the cap and
drawer.
drawer.
Is the pulley bolt loosened?
Is the belt worn?
Is there friction noise from the motor?
Is water supplied?
Are receptacles correctly connected to the
terminals of inlet valve?
terminals of inlet valve?
Is softener put in the correct compartment of
drawer?
drawer?
Is the softner cap clogged?
21
NO
NO
Y E S
Y E S
Y E S
NO
NO
NO
NO
Y E S
Y E S
NO
P WB AS S E MB LY
P WB AS S E MB LY
1 2
R eplace the sensor
(pressure).
(pressure).
R eplace the P WB
Assembly.
Assembly.
R epair drain hose
R emove foreign
material.
material.
R econnect or repair the
connector
connector
R eplace the pump
assembly
assembly
R eplace the P WB
C hecking voltage between two pins as press
the power button is the voltage 220-240V ~?
the power button is the voltage 220-240V ~?
Is the drain hose twisted or frozen?
Is the impeller of the drain pump clogged?
Is the connector disconnected,
disassembled?
disassembled?
Is the coil of drain pump cut-off?
(resistance of coil is 90~160 )
(resistance of coil is 90~160 )
When checking voltage between connectors
( , )on spinning, is the voltage
220 - 240V ~ as the figure?
( , )on spinning, is the voltage
220 - 240V ~ as the figure?
Is the sensor working?
HE AT ING WIT HOUT WAT E R
DR A IN MA L F UNC T IONING
22
AC 220-240V
(1)
1
6
Replace the thermistor
Push the thermistor
tightly to the rubber.
When disconnecting the connector (1) on the
PWB assembly (Main) is the resistance of the
Natural connectors [ (Blue White),
PWB assembly (Main) is the resistance of the
Natural connectors [ (Blue White),
(White)]
between 2.5k
Ω
to 180k
Ω
(105°C~0°C)?
When checking thermistor on the tub,
is the thermistor loosened above 2mm from
the rubber?
HEATING CONTINUOUSLY ABOVE
THE SETTING WATER TEMPERATURE
23
NO
Y E S
Y E S
Y E S
NO
NO
NO
Y E S
1
10
5
1 2 3 4 5 6 7 8 9 10
3
5
2
1
4
S P IN T R OUB L E
C heck the sensor
(Pressure) or hose
(S ensor).
If the problem is on the
sensor or the hose, replace
the sensor or the hose.
(Pressure) or hose
(S ensor).
If the problem is on the
sensor or the hose, replace
the sensor or the hose.
Normal
R econnect or repair it.
R eplace the motor
assembly.
assembly.
Press [Power] button with [Option1] and [Option2]
buttons pressed after power off. Press [S tart/Pause]
button 2 times. Does the drum rotate at low spin
speed?
buttons pressed after power off. Press [S tart/Pause]
button 2 times. Does the drum rotate at low spin
speed?
Is it disconnected or badly contacted?
[White : 2 pin ( ), Black : 2 pin ( ), White : 3 pin ( ),
Blue : 4 pin ( ), White : 4 pin ( )]
[White : 2 pin ( ), Black : 2 pin ( ), White : 3 pin ( ),
Blue : 4 pin ( ), White : 4 pin ( )]
Check the motor connector, Is the resistance between
the terminal in figure the same as below?
R esistance between terminals
~
the terminal in figure the same as below?
R esistance between terminals
~
: 0.5 ~ 1.0
~
• : 1.5 ~ 2.5
Be sure to unplug the machine before measuring.
MOTOR TE R MINAL
MOTOR TE R MINAL
R eplace the PWB assembly.
Is the sensor or hose correct?
Click on the first or last page to see other WD-10660N service manuals if exist.