DOWNLOAD LG WD-10490NP Service Manual ↓ Size: 7.52 MB | Pages: 35 in PDF or view online for FREE

Before servicing ask the customer what the trouble is.
Check the adjustment (power supply is 220-240V, remove the transit bolts....)
Check the troubles referring to the troubleshooting.
Decide service steps referring to disassembly  instructions.
Then, service and repair.
After servicing, operate the appliance to see whether it works O K or NOT.

STANDARD INSTALLATION

The appliance should be installed as follows.

REMOVE THE TRANSIT 

INSTALL THE  APPLIANCE

ADJUST THE 

BOLTS

ON FLAT AND FIRM SURFACE

HORIZONTAL

Remove the transit bolts

Turn the adjustable feet to

(4EA: ) with supplied wrench. 

set the appliance horizontally.

Keep the transit bolts and  

wrench for future use.

Insert the 4 caps provided 

into the hole.

The appliance goes up by 

rotating the feet clockwise. 

The appliance comes down by

rotating the feet counter-

clockwise.

4. INSTALLATION 

1

HOW TO CONNECT INLET HOSE

Check that the rubber washer is the inside of the

valve connector.

Connect inlet hose firmly to prevent leak.

CONNECT DRAIN HOSE

CONNECT POWER PLUG

Make sure that the hose is not twisted.

The drain hose should be placed under 100cm from the floor.

Connect the power plug to the wall outlet.

Avoid connecting several electric devices, 

It may be the cause of a fire.

Avoid submerging the end of the hose.

TEST OPERATION

Connect the power plug to

In case of cotton program.      

the outlet.

Connect the inlet hose.   

Preparation for 

Press the power button.

Press the START/PAUSE

washing.

button.

Power off and  then power on.
Check if the door can be 
opened after 2 minutes.

Press the Start/Pause button
after selecting Pump button by
pressing Program button.

If SVC is needed during 

check, remove

the remaining water by pulling 

out the hose cap.

Check the water heating.

Check automatic reverse

Check the water supply.

turn.

Check drain and spin 

Power off and open the 

Water removal 

door

Check if the drum rotates  

Check if water is supplied

clockwise and  counterclockwise.  

through the detergent dispenser.

5. OPERATION

Press the button to select
water temperature.
The water temperature 

[60 C 

➔

95 C

➔

Cold 

➔

30 C 

➔

40 C] can be

selected in Cotton. 

95 C  is selected for Cotton
and Baby Care.

Used to additional rinse, which may
assist in removing traces of detergent
residue.

• By selecting Rinse+ function, the rinse

time and the rinse water are increased.

If the laundry is heavily soiled, “Pre
Wash” course is effective.
Pre Wash is available in Cotton and
Synthetic Program.

If you want to prevent crease,
select this button with spin speed.

Bio
• If you want to eliminate protein

stains(milk, blood, chocolate...), 
you may select Bio by pressing the
option button.[You can select Bio
when temperature is higher than
60°C in Cotton, Synthetic and Baby
Care.]

• Display the estimated

remaining time
(Hour:Minute) to finish.

• In case of abnormal

operation, error indications
are dispayed.
(                                       )

• See troubleshooting guide.

N O T E

If the Program lamps are blinked at the same time after the 
power off or the end of the washing, the child lock mode is set. 
Cancel the child lock mode by pressing the [Temp.] and the [ Option]
button simultaneously for 3 seconds.

Child Lock system can be set and canceled by pressing both
[Temp.] and [Option] button simultaneously for 3 seconds.
Once Child Lock is set, all buttons are not functioning except
power button.
Child Lock system can be set anytime even during Power-off
and operation.
It is automatically cancelled when an operational error occurs.