LG WD-10401TD Service Manual ▷ View online
28
DOOR ASSEMBLY
Open the door completely.
Remove the two screws from the hinge.
When removing the DOOR ASSEMBLY, it is necessary to
hold the BRACKET that is inner of the CABINET COVER.
hold the BRACKET that is inner of the CABINET COVER.
Take apart the CLAMP ASSEMBLY (cabinet).
Unscrew 2 screws from the CABINET COVER.
Open the lower cover cap and unscrew 1 screw inside
(Refer to page 27)
(Refer to page 27)
Take apart the LOWER COVER.
Disassemble the CONTROL PANEL ASSEMBLY.
(Refer to page 25)
(Refer to page 25)
Unscrew all the screws on the upper and lower sides of
the CABINET COVER.
the CABINET COVER.
Take apart the tub CLAMP ASSEMBLY
Make sure that the drain hole of the GASKET is put
beneath when reassembling the GASKET.
beneath when reassembling the GASKET.
Refer to the arrow mark on the TUB COVER.
GASKET
29
■
■ Clean the drain pump filter
1. Open the lower cover cap ( )by
using a coin. Turn the drain plug
( )to pull out the hose.
2. Unplug the drain plug ( ),
allowing the water to flow out. At
this time use a vessel to prevent
water flowing on to the floor.
When water does not flow any
more, turn the pump filter
( )open to the left.
3. Remove any foreign material from
the pump filter ( ). After
cleaning, turn the pump filter ( )
clockwise and insert the drain
clockwise and insert the drain
plug ( )to the original place.
close the lower cover cap.
close the lower cover cap.
ROTOR ASSEMBLY, STATOR ASSEMBLY, FRICTION DAMPER ASSEMBLY
(ROTOR ASSEMBLY)
(STATOR ASSEMBLY)
(FRICTION DAMPER ASSEMBLY)
Damper
Rotor
Bolt
Hinge
(1)
Remove the BACK COVER.
Unscrew the bolt to pull out the ROTOR ASSEMBLY.
Disconnect the wiring connector.
Unscrew 6 bolts from the STATOR.
Remove the BODY FRAME. (Only 1400 rpm models)
Note :Hook of connector (1) is on the backside
Pull out the HINGE, pressing its snap.
Do not use the pulled out HINGE again
It may be taken off during operation.
It may be taken off during operation.
30
Remove pump outlet hose.
Remove tub pump bellows.
Remove cap (Remaining Hose.)
Disconnect the wiring.
Unscrew 2 screws.
Remove the pump.
Loosen the M6 heater nuts to pull out the HEATER
ASSEMBLY.
ASSEMBLY.
When mounting the HEATER ASSEMBLY be sure to
insert the HEATER ASSEMBLY into the heater clip on
the bottom of the tub.
Pull it out by holding the THERMISTOR bracket.
If it is pulled by the wire, it may be broken.
If it is pulled by the wire, it may be broken.
When mounting the THERMISTOR again, make sure
that it is got back tight to the bushing.
that it is got back tight to the bushing.
DRAIN PUMP ASSEMLBY
HEATER ASSEMBLY
THERMISTOR
CAUTION
Take apart the CLAMP ASSEMBLY (cabinet) and release
the GASKET.
the GASKET.
Unscrew 2 screws holding the DOOR SWITCH
ASSEMBLY.
ASSEMBLY.
Disconnect the door lock from the wiring connector.
Remove the HEATER ASSEMBLY.
Remove the foreign material (wire, coin and others) by
inserting a long bar through the hole.
inserting a long bar through the hole.
31
SWITCH ASSEMBLY, DOOR LOCK
WHEN FOREIGN MATERIAL IS STUCK BETWEEN DRUM AND TUB
Click on the first or last page to see other WD-10401TD service manuals if exist.