LG WD-10316FDK Service Manual ▷ View online
24
NO
YES
YES
YES
NO
NO
NO
YES
(1)
S P I N T R O U B L E
Check the S.PRESSURE SWITCH
ASSEMBLY or HOSE (Pressure).
If the problem is on the
S.PRESSURE SWITCH
ASSEMBLY or the HOSE, replace
the S.PRESSURE SWITCH
ASSEMBLY or the HOSE.
ASSEMBLY or HOSE (Pressure).
If the problem is on the
S.PRESSURE SWITCH
ASSEMBLY or the HOSE, replace
the S.PRESSURE SWITCH
ASSEMBLY or the HOSE.
Normal
Correct the connector.
Replace the STATOR
ASSEMBLY
ASSEMBLY
Check on the spinning, is the frequency of the
water level 248 or more. The frequency can be
checked by pressing the Wash and Rinse buttons at
the same time on the program.
water level 248 or more. The frequency can be
checked by pressing the Wash and Rinse buttons at
the same time on the program.
When pressing Rinse, Spin and POWER buttons at
the same time after power off, press the Start/Pause
button 1 times, is the drum low speed spin?
the same time after power off, press the Start/Pause
button 1 times, is the drum low speed spin?
Is it disconnected, or disassembled?
[Red:3pin(1), GY:4pin(2)]
[Red:3pin(1), GY:4pin(2)]
Check the motor connector, is the resistance of
the terminal same as the figure?
MOTOR TERMINAL (1)
Resistance of terminal:
About 5
15
Replace the MAIN PWB ASSEMBLY
Does the spring of Latch Hook actuate?
Is there clicking sound once or twice when the
START/ PAUSE button is pressed to start the cycle?
START/ PAUSE button is pressed to start the cycle?
Is DOOR SWITCH ASSEMBLY broken?
Replace Door Assembly.
Check the DOOR SWITCH
ASSEMBLY Connector and
MAIN PWB ASSEMBLY
(Red 3 pin, Yellow 4 pin and
white 3 pin connector (1)).
ASSEMBLY Connector and
MAIN PWB ASSEMBLY
(Red 3 pin, Yellow 4 pin and
white 3 pin connector (1)).
Replace the DOOR
SWITCH ASSEMBLY.
SWITCH ASSEMBLY.
9. DISASSEMBLY INSTRUCTIONS
Disassemble and repair the parts after pulling out power cord from the outlet.
①
Unscrew the screws on the top plate.
②
The plate assembly(Top) is pulled back and
then upward to arrow direction.
then upward to arrow direction.
③
The cover(Inner) is disassembled.
①
The PWB assembly(Display) connectors are
disconnected.
disconnected.
②
Pull out drawer, three screws are unscrewed.
③
Push two upper hooks and pull the control
panel forward.
①
The PWB assembly(Display) is disconnected.
②
When 6 screws are unscrewed on the PWB
insulator and the PWB assembly(Display) is
disassembled from the PWB insulator.
insulator and the PWB assembly(Display) is
disassembled from the PWB insulator.
PANEL ASSEMBLY(CONTROL)
Hook
CONTROL PANEL
PLATE ASSEMBLY(TOP)
PWB ASSEMBLY(DISPLAY)
25
26
①
The back cover is removed.
②
Two screws are unscrewed.
③
Disconnect connector from the wiring.
④
Pull the PWB assembly (Main) to arrow
direction.
①
The plate assembly(Top)and the
cover(lnner)are disassembled.
②
Pull the drawer to arrow direction.
③
Two screws are unscrewed.
①
The hose clamps and the hose are
disassembled.
②
The ventilation bellows are disassembled on
the tub.
PWB ASSEMBLY(MAIN)
DISPENSER ASSEMBLY
DRAWER
Option
Dispenser assembly
27
①
Disconnect the wiring connector.
②
Remove the valve by two screws of the valve
holder.
When reconnecting the connector
INLET VALVE
1
2
3 Option
VALVE
(PRE-WASH)
GY/WH - BK
VALVE
(NORMAL-WASH)
WH/BK - BK
VALVE
®È
(NORMAL-WASH)
BL/RD - BK
VALVE
(HOT)
BL/RD - BK
①
Open the door completely.
②
Remove the two screws from the hinge.
※
When removing the Door Assembly, it is
necessary to hold the Bracket that is inner of
the Cabinet Cover.
the Cabinet Cover.
Pull it out from hose.
※
First, prepare a bucket to put in the remained
water.
CAP
(REMAINING HOSE)
DOOR
Removing method of remained water
Click on the first or last page to see other WD-10316FDK service manuals if exist.