DOWNLOAD LG TR1103AEP5 Service Manual ↓ Size: 4.18 MB | Pages: 58 in PDF or view online for FREE

Many washing problems involve poor soil & stain removal, residues of lint and scum, and fabric damage. For
satisfactory washing results, follow these instructions.

Poor soil
removal

• Not enough Detergent
• Wash Water

Temperature too low.

• Overloading the washer
• Incorrect wash cycle
• Incorrect sorting
• Stain not pre treated.

• Use correct amount of Detergent for load size, amount of soil and

water Hardness.

• Use WARM or HOT water for normal soil.

Different Water Temperature may be required according to soil
type. (refer to page 10)

• Reduce load size.
• Wash with JEAN or  SOAK & JEAN wash cycle for heavy soiled

laundry.

• Separate heavily soiled items from lightly soiled ones. 
• Pretreat stain and heavy soil according to directions shown on

page 9.

Blue, Grey, or
Brown Stains

• Undiluted fabric softener

dispensed directly onto
fabric

• Rub the stain with bar soap. Wash.
• Do not overfill fabric softener dispenser and do not pour liquid

fabric softener directly onto fabric. 
See page 12 for more instructions.

Black or Gray
marks on
clothes

• A buildup caused by the

interaction of fabric
softener and Detergent
can flake off and mark
clothes 

• Not enough Detergent

• Refer to the recommendations against Scrud(waxy buildup). 

(refer to scrud page12.) 

• Use correct amount of Detergent for load size, amount of soil

and water Hardness.

Yellow or
brown rust
stains

• Iron or manganese in

water supply, water
pipes, or water heater

• To restore discolored load of whites, use rust remover safe for fabric.
• Install nonprecipitating water softener or an iron filter in your

water supply system for an ongoing problem. 

• Before washing, run water for a few minutes to clear lines.

Lint

• Incorrect sorting 
• Tissues left in pocket 
• Overloading the washer

• Wash lint givers eg towels, flannelette sheets, separately from

lint collectors eg synthetic fabrics and remove tissues in pockets
before wash. See page 9 for sorting and caring before loading. 

• Do not overload the washer

Residue or
Detergent

• Overloading the washer 
• Undissolved Detergent
• Too much Detergent

• Do not overload the washer.
• Some Detergents need to be pre-dissolved, check the Detergent

instructions. Try pre-dissolving the detergent in warm water. 

• Increase Water Temperature using HOT water safe for fabric.
• Use proper amount of Detergent.

Holes, tears,
or snags

• Incorrect use of chlorine

bleach.

• Unfastened zippers,

hooks, buckles 

• Ribs, tears and broken

threads

• Overloading the washer
• Degradation of fabric

• Never pour chlorine bleach directly on fabric. 

See page 11 for adding liquid bleach.

• Fasten zippers, hooks, and buckles.
• Remove objects in pockets. See page 9 for caring before

loading.

• Do not overload the washer.

For more detailed information for trouble shooting refer to page 42 to 51.

ERROR

WATER

SUPPLY 

DRAINAGE

UNBALANCE

DOOR 

OPEN

WATER LEVEL
dose not rise to
the set level in 30
minutes.

"NO INLE"

lamp blinks

Water is not
completely
drained in 12
minutes.

Laundry
unbalance during
spin.

LID is opened in
the course of
intermittent spin,
normal spin or
processing
reservation.
SIGNAL
continuously
ringing. 
“DOOR OPEN ”
lamps blinks.

Water faucet is closed?
Water supply is interrupted.

Inlet V/V is clogged with
dirts.
Connector has bad contact
to the inlet valve.
BLUE 6 pin connector has
bad contact to the P.W.B
ASM.

Is the drain hose located
properly?
Drain hose is folded or
clogged due to freeze or dirt.
Bad Drain Pump part or
BLUE (WHITE) 3 pin
connector to the P.W.B ASM
has bad connection.

Laundry in the INNER TUB
is filled unevenly.

Washer is tilted.

Lid is opened during
intermittent spin or normal
spin?
Lid is opened while
processing reservation?
Connector to the Lid S/W or
NATURAL 6pin connector to
the P.W.B ASM has bad
connection.

Open water faucet.
Wait until water supply is
resumed.
Clean or replace filter.
Correct the connector
contact.
Same as above.

Hung up drain hose at
0.9~1.2m high.
Unclose the foreign objects
within drain hose.
Replace Drain Motor or
correct the connector
contact.

Try to fill laundry uniformly
in the inner tub.

Adjust the leg.

Closed the lid.

Closed the lid.

Correct the connector
contact.
Check and replace Lead
Wire Asm.

ERROR DECISION

BASIS

CAUSE FOR ERROR

OCCURRENCE

REMEDY

ERROR

OVER

FLOODING

ERROR

PRESSURE

SENSOR

MOTOR

ERROR

Water Pressure
Switch is off.

Check water leakage or
whether the drain hose is
hung on to drainage which is
0.9 m obove from floor.
Check blockage of air hole
or air tube.
Check &repair air leakage at
the air hole of outer tub the
air tube or connection parts.

Connector the PRESSURE
S/W ASM or BLUE 4 pin
connector to P.W.B ASM has
bad connection.
PRESSURE S/W is bad. (In
the initial state of QC TEST
MODE, the number on the
DISPLAY is less than 60 or
more than 104)

Connector the HALL Sensor
or Natural 6 Pin connector
to P.W.B ASM had bad
connection .
Connector the stator ASM,
and YELLOW 3 Pin or
Natural 6 Pin connector to
P.W.B ASM had bad
connection
Hall sensor is bad.
Locked by Bearing Housing

Hang drain hose which is
minimum 0.9m above from
floor.
Replace pressure sensor
switch
Remove the foreign objects
in pressure sensor switch

Correct the connector
contact.

Replace PRESSURE S/W
ASM.

Correct the connect contact.
Change Stator ASM.
Change Bearing Housing
ASM.
Change P.W.B ASM.
Change Stator ASM.

ERROR DECISION

BASIS

CAUSE FOR ERROR

OCCURRENCE

REMEDY

Where, what & how to check?

Result of Check

Possible Cause

How to repair & settle

1. Check whether connection between the

plug and the electrical is poor

2. Measure voltage of the electrical.

1. Measure resistance between both ends

of the power supply cord with both the
plug pins short-circuited.

2. Check whether every connector in the

bundle of connectors has a good
connection.

3. Check resistance of every wire to find

out a open wire.

1. Check resistance with power relay

switch turned on

2. Check the secondary voltage of the

transfomer.

3. Check whether the fuse is open.

If there are no defects in the above, 
it should be defect of the controller.

Poor

Around rating

0 V 

Less than 1

∞

Male & female
connectors separated

∞

Less than 0.5

More than 1.0 

10~14 V

0 V

Open

Over 120% voltage
than rating check

Change the controller if all
the electrical parts have no
defects.

Defect of the electrical

No defect

Defect of household
power supply

No defect

Open circult of the power
supply cord

Poor connection

Wire is opened.

No defect

Poor contact

No defect

Coil is open

Defect of the fuse

Change the electrical.

Call for power supply
company

Change the power supply
cord.

Remove the cause to give
strain and reconnect
them.

Change the lead wire

Change the AUTO OFF
Switch

Change the

transfomerformer.

Change the fuse.
CAUTION
Check the fuse rating
AC100~127V:125V 12A
AC220~240V:250V 6A