DOWNLOAD LG T1203AFPT1 Service Manual ↓ Size: 14.93 MB | Pages: 60 in PDF or view online for FREE

Water Guide

Fixing Bolt

Hall Sensor

Stator Housing

Disassemble rotor nut with boxer(M18) or spaner.
( In assembled, the force is over than 200kgf.cm)

Disassemble rotor,  pull out the rotor as shown the
figure.

Disconnect fixing screw and disassemble the water
guide.

Before disassemble stator,disconnect the hall sensor
and stator housing.

SNAP RING.

Hall Sensor

Stator Housing

Water Guide

Loosen the 6 fixing screws on the stator. 
(Lower 

upper position screws)

Check the direction of SNAP RING.
(The handle of snap ring is toward to rotor and stator.)

Preventing fallen the stator, tighten with one hand and
then loosen the last screw.

For assembly take care lead wire's state, it produce a
noise and cut attach the rotor.

Loosen 14 Fixing screws on the Bearing Housing ASM
and pull up it.

4-6.  TROUBLE SHOOTING AGAINST COMMON WASHING PROBLEMS

Many washing problems involve poor soil & stain removal, residues of lint and scum, and fabric damage. For

satisfactory washing results, follow these instructions.

Poor soil

removal

Not enough Detergent

Wash Water

Temperature too low.

Overloading the washer

Incorrect wash cycle

Incorrect sorting

Stain not pre treated.

Use correct amount of Detergent for load size, amount of soil and

water Hardness.

Use WARM or HOT water for normal soil.

Different Water Temperature may be required according to soil

type. 

Reduce load size.

Wash with JEAN or  SOAK & JEAN wash cycle for heavy soiled

laundry.

Separate heavily soiled items from lightly soiled ones. 

Pretreat stain and heavy soil according to directions shown on

page 11.

Blue, Grey, or

Brown Stains

Undiluted fabric softener

dispensed directly onto

fabric

Rub the stain with bar soap. Wash.

Do not overfill fabric softener dispenser and do not pour liquid

fabric softener directly onto fabric. 

See page 14 for more instructions.

Black or Gray

marks on

clothes

A buildup caused by the

interaction of fabric

softener and Detergent

can flake off and mark

clothes 

Not enough Detergent

Refer to the recommendations against Scrud(waxy buildup). 

(refer to scrud page14.) 

Use correct amount of Detergent for load size, amount of soil

and water Hardness.

Yellow or

brown rust

stains

Iron or manganese in

water supply, water

pipes, or water heater

  To restore discolored load of whites, use rust remover safe for fabric.

Install nonprecipitating water softener or an iron filter in your

water supply system for an ongoing problem. 

Before washing, run water for a few minutes to clear lines.

Lint

Incorrect sorting 

Tissues left in clothes

      pocket 

Overloading the washer

Wash lint givers eg towels, flannelette sheets, separately from lint

   collectors eg synthetic fabrics and remove tissues in clothes pockets

before wash. See page 9 for sorting and caring before loading. 

Do not overload the washer

Residue or

Detergent

Overloading the washer 

Undissolved Detergent

Too much Detergent

Do not overload the washer.

Some Detergents need to be pre-dissolved, check the Detergent

instructions. Try pre-dissolving the detergent in warm water. 

Increase Water Temperature using HOT water safe for fabric.

Use proper amount of Detergent.

Holes, tears,

or snags

Incorrect use of chlorine

bleach.

Unfastened zippers,

hooks, buckles 

Ribs, tears and broken

threads

Overloading the washer

Degradation of fabric

Never pour chlorine bleach directly on fabric. 

See page 14 for adding liquid bleach.

Fasten zippers, hooks, and buckles.

Remove objects in pockets. See page 9 for caring before

loading.

Do not overload the washer.

(refer to page 12)

• If you press the START/PAUSE button when an error is displayed, any error except             will disappear and 

the machine will go into the pause status.

• In case of            ,             if the error is not resolved within 20 seconds, or the in case of other errors, if the

error is not resolved within 4 minutes, power will be turned off automatically and the error code will blink. But in
the case of           , power will not be turned off.

• Clutch Motor defect

CLUTCH ERROR

7

• Door not all the way closed.

DOOR OPEN
ERROR

6

• The PRESSURE SENSOR ASSEMBLY is out of  

order.

• When water level frequency maintain condition of below 20 kHz  

and over 30 kHz

PRESSURE
SENSOR
ERROR

5

• Water is overflowing 

(water level frequency is over 21.7 kHz).

If    

FE is displayed, the drain pump will   

operate to drain the water automatically.

OVERFLOW
ERROR

4

DRAIN ERROR

3

• The load is too small.
• The appliance is tilted.
• Laundry is gathered to one side.
• Non distributable things are put into the drum.

UNBALANCE
ERROR

2

WATER INLET
ERROR

1

CAUSE

SYMPTOM

ERROR

• Clutch Motor defect

CLUTCH ERROR

7

• Door not all the way closed.

DOOR OPEN
ERROR

6

• The PRESSURE SENSOR ASSEMBLY is out of  

order.

• When water level frequency maintain condition of below 

and over 30 kHz

PRESSURE
SENSOR
ERROR

5

• Water is overflowing 

(water level frequency is over 21. 

If    

FE is displayed, the drain pump will   

operate to drain the water automatically.

OVERFLOW
ERROR

4

DRAIN ERROR

3

• The load is too small.
• The appliance is tilted.
• Laundry is gathered to one side.
• Non distributable things are put into the drum.

UNBALANCE
ERROR

2

WATER INLET
ERROR

1

CAUSE

SYMPTOM

ERROR

shock when disconnecting parts while trouble shooting. (Wear Electro Static Discharge gloves when working.)

After cutting off the power when changing PCB assembly, disconnect or assemble.

Be careful static when handling PCB assembly,  and use Electro Static Discharge plastic pack 

when delivering or keeping it. 

There’s built-in AC 120V and DC power in output terminal of  PCB assembly in common. Be careful electric

• Correct water leve

(26k

 is not reached within 12  

minutes after water is supplied or it 

   the preset 

water level 

within 10 minutes.

 

• Correct water leve

Hz),but not change 

(26k

 

Hz)  is not reached within 

minutes after water is supplied or it  reach 

 preset 

water level

l 

within   minutes.

• Not fully drained within 12 minutes.

• Not fully drained within 1  minutes.