DOWNLOAD LG T1001TEPT Service Manual ↓ Size: 5.22 MB | Pages: 52 in PDF or view online for FREE

Rubber packing

Screw

Fixed sticker

Rubber packing

Guide plate

Connector

Connector

Fixed sticker

Middle
Connector

Middle
Connector

Water Supply Hose

Pressing rod

Pressing handle

Connector

Middle
connector

Fixed Stiicker

Pressing Handle

Pressing Rod

Water Supply Hose

Separate Middle connector from the Water Supply
Hose by pulling the Pressing Rod and the Pressing
Handle that is attached to the Water Supply Hose
while pressing them.

Untighten the screw of the connector so that the
tap can be placed in the middle.

Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.

Remove the fixed sticker in between the Upper
and Middle Connectors. Tighten the connectors
by holding one connector and twist middle
connector to the right.

Press down the pressing rod of the Water
Supply Hose which was separated from middle
connector(refer to Step1) and then join it to the
middle connector.

One Touch Type

If the tap diameter is too large or is square, open
the 4 screw and take out the guide plate and
follow step 1.

In case the tap is large.

After connecting the hose, open the tap to check for
any water leakage.
In case of water leakage, close the tap and start again
from step 1. 
If you skip step1, it may cause water leakage.

(NORMAL TAB WITHOUY THREAD & ONE TOUCH TYPE INLET HOSE.)

Push the water supply hose up so that
the rubber packing within the hose can
adhere completely to the tap.

Connect the water supply hose to the tap and
then tighten it by screwing it to the right.

After connecting the hose, open the
faucet to check for any water leakage.

Connect the water supply hose to inlet valve of
the washing machine, and then lock it by turning
the hose connecting part.

Check to see if there is a rubber seal inside 
the connector.

Screw Type

Water Supply Hose

Rubber Packing

H

Rubber seal

Water

tap

Hose

Guide

0.9~1.2m

Drain Hose

Within 50mm

Connect the drain hose to 

the outlet of the drain pump
located at the rear of the
washing machine.

Attach the clip to the drain 

hose. And then push it toward
the body of the washing 
machine as indicated by the
arrow.

Check that the drain hose is
hung up over the edge of the
laundry tub.
Do not use an extension
hose.

Connect the drain hose to the outlet of the 

drain located at the back side of the
washing machine.

Fix the drain hose with the clip.

And then push it toward the body as in the
figure.

Keep it downward while the washing machine

is working.

Ensure the hose is free from kinking.

Never lay down the drain hose, as water will be 
discharged.

Be sure the drain hose is properly routed so it will not
kink or lift  from the sink.

The discharge height should be approximately 0.9~1.2m from 

the floor.

Connect the drain hose adjusting the length of it not to be

dropped. If drain hose is dropped the drainage could be poor
because of blockage in the hose.

WATER SUPPLY
HOSE

Make sure the water 
does not leak.

DISPENSOR FOR
LIQUID DETERGENT
& BLEACH

FUNCTION SELECTOR

PULSATOR

TUB

ADJUSTABLE LEGS

Use to level the washing
machine for correct balance
& spin operation.

Check if the drain hose 
is hung up before 
operating the 
washing machine.

DRAIN HOSE
for pump model

DRAIN HOSE
for non pump model

POWER PLUG

If the supply cord is 
damaged, it must be 
replaced by the 
manufacturer
or its service agents 
or similarly qualified 
person in order to 
avoid a hazard.

LINT FILTER

Clean regularly to stop 
linting on the clothes 
load.

*

*

*

*

Softener will automatically
flow into the tub.

* SOFTENER  INLET

POWDER DETERGENT & BLEACH
BOX FOR DELAYED
WASHING

START/PAUSE
BUTTON

Use to start or stop the 
washing machine
temporarily.

(           )