LG T1001TEPT Service Manual ▷ View online
2-2. CONNECTING WATER SUPPLY HOSE
6
Before connecting Water Supply Hose to water tap, check your hose type and choose
correct instruction. Water Supply Hose may vary according to the country.
Make sure connect blue inlet hose to cold water tab, and orange inlet hose to hot water tab.
correct instruction. Water Supply Hose may vary according to the country.
Make sure connect blue inlet hose to cold water tab, and orange inlet hose to hot water tab.
Connecting Water Supply Hose to water tap
Rubber packing
Water supply hose
Connector
Untighten the screw
Untighten the screw of the connector so
that the tap can be placed in the middle.
that the tap can be placed in the middle.
Fixing the connector to the tap
Push the upper connector up till the
rubber packing is in tight contact with the
tap. Then tighten the 4 screws.
rubber packing is in tight contact with the
tap. Then tighten the 4 screws.
Attach the water supply hose to the connector
Push the water supply hose vertically
upwards so that the rubber seal within the
hose can adhere completely to the tap.
upwards so that the rubber seal within the
hose can adhere completely to the tap.
Check the connection of water supply hose and
the connector
the connector
After connecting the hose, open the tap
to check for any water leakage.
In case of water leakage, close the tap
and start again from step 1
to check for any water leakage.
In case of water leakage, close the tap
and start again from step 1
Fixing the connector of connector and water
supply hose
supply hose
Attach the water supply hose to the
connector and then tighten it by screwing
it to the right.
connector and then tighten it by screwing
it to the right.
Normal Type
Normal tab without thread & screw type inlet hose.)
1
2
3
4
5
7
Rubber packing
Screw
Fixed sticker
Rubber packing
Guide plate
Connector
Connector
Fixed sticker
Middle
Connector
Connector
Middle
Connector
Connector
Water Supply Hose
Pressing rod
Pressing handle
Connector
Middle
connector
connector
Fixed Stiicker
Pressing Handle
Pressing Rod
Water Supply Hose
Separate Middle connector from Water
Supply Hose
Supply Hose
Separate Middle connector from the Water Supply
Hose by pulling the Pressing Rod and the Pressing
Handle that is attached to the Water Supply Hose
while pressing them.
Hose by pulling the Pressing Rod and the Pressing
Handle that is attached to the Water Supply Hose
while pressing them.
Loosen the fixed nuts to connect the connector to the tap
Untighten the screw of the connector so that the
tap can be placed in the middle.
tap can be placed in the middle.
Fixing Connectors to the Tap
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.
packing is in tight contact with the tap. Then
tighten the 4 screws.
Fixing Upper Connector and Middle
Connector
Connector
Remove the fixed sticker in between the Upper
and Middle Connectors. Tighten the connectors
by holding one connector and twist middle
connector to the right.
and Middle Connectors. Tighten the connectors
by holding one connector and twist middle
connector to the right.
Connecting Middle Connector and
Water Supply Hose
Water Supply Hose
Press down the pressing rod of the Water
Supply Hose which was separated from middle
connector(refer to Step1) and then join it to the
middle connector.
Supply Hose which was separated from middle
connector(refer to Step1) and then join it to the
middle connector.
One Touch Type
If the tap diameter is too large or is square, open
the 4 screw and take out the guide plate and
follow step 1.
the 4 screw and take out the guide plate and
follow step 1.
In case the tap is large.
Note
Checking the water leakage
After connecting the hose, open the tap to check for
any water leakage.
In case of water leakage, close the tap and start again
from step 1.
If you skip step1, it may cause water leakage.
any water leakage.
In case of water leakage, close the tap and start again
from step 1.
If you skip step1, it may cause water leakage.
(NORMAL TAB WITHOUY THREAD & ONE TOUCH TYPE INLET HOSE.)
1
2
3
4
5
6
8
Attach the water supply hose to the tap.
Push the water supply hose up so that
the rubber packing within the hose can
adhere completely to the tap.
the rubber packing within the hose can
adhere completely to the tap.
Connect the water supply hose to the tap.
Connect the water supply hose to the tap and
then tighten it by screwing it to the right.
then tighten it by screwing it to the right.
Check water leakage.
After connecting the hose, open the
faucet to check for any water leakage.
faucet to check for any water leakage.
Connect the water supply hose to inlet valve of
the washing machine, and then lock it by turning
the hose connecting part.
the washing machine, and then lock it by turning
the hose connecting part.
Check to see if there is a rubber seal inside
the connector.
the connector.
Screw Type
Water Supply Hose
Rubber Packing
H
Rubber seal
Water
tap
Connecting Water Supply Hose to the machine
1
2
3
9
2-3. CONNECT THE DRAIN HOSE
CAUTION
Hose
Guide
0.9~1.2m
Drain Hose
Within 50mm
Connect the drain hose to
the outlet of the drain pump
located at the rear of the
washing machine.
located at the rear of the
washing machine.
Attach the clip to the drain
hose. And then push it toward
the body of the washing
machine as indicated by the
arrow.
the body of the washing
machine as indicated by the
arrow.
Check that the drain hose is
hung up over the edge of the
laundry tub.
Do not use an extension
hose.
hung up over the edge of the
laundry tub.
Do not use an extension
hose.
Connect the drain hose to the outlet of the
drain located at the back side of the
washing machine.
washing machine.
Fix the drain hose with the clip.
And then push it toward the body as in the
figure.
figure.
Keep it downward while the washing machine
is working.
Ensure the hose is free from kinking.
Never lay down the drain hose, as water will be
discharged.
discharged.
Be sure the drain hose is properly routed so it will not
kink or lift from the sink.
kink or lift from the sink.
The discharge height should be approximately 0.9~1.2m from
the floor.
Connect the drain hose adjusting the length of it not to be
dropped. If drain hose is dropped the drainage could be poor
because of blockage in the hose.
because of blockage in the hose.
NOTE
:
Do not install the washer where it is directly exposed to sunlight, wind, rain etc.
Plug the power cord of this washer into a properly installed standard electrical outlet
that is switched & earthed.
For pump model
For non - pump model
Click on the first or last page to see other T1001TEPT service manuals if exist.