LG T1001TEPT Service Manual ▷ View online
2. INSTALLATION INSTRUCTIONS
2-1. HOW TO ADJUST LEVEL
4
How to use the adjusting plates
·
Use the adjusting plates to level the washer when
the adjustable legs cannot cover the gap.
the adjustable legs cannot cover the gap.
1
2
Adjustable leg
Turn the adjustable legs to set the washer
horizontal (2 EA).
horizontal (2 EA).
Installation area
·
Install the washer on flat and firm
surface.
Improper installation of the washer may cause noise and malfunctioning.
1. The ventilating openings in the base area must not be obstructed be
carpeting
when the washing machine is installed on a carpeted floor.
when the washing machine is installed on a carpeted floor.
2. Install the washing machine on a level and firm surface, any tilt
should be less than 1
°
°
.
CAUTION
Checking level
·
Open the lid, and check if the washer
is correctly leveled by looking down
from the top.
is correctly leveled by looking down
from the top.
5
More than 10cm
More than 2cm
More than 2cm
3
5
4
Horizontal setting
·
Lift up the front of the washer and
adjust level by turning the adjustable
legs clockwise or using the adjusting
plate.
legs clockwise or using the adjusting
plate.
Confirming level
Distance between drain hose and the wall
Checking slope
·
If installation surface is tilted, the
washer will be shaken.
washer will be shaken.
·
Place the washer to original position
and confirm the level.
·
Distance between drain hose and the wall
should be more than 10 cm, and the
distance between the other part and the
wall should be more than 2 cm.
should be more than 10 cm, and the
distance between the other part and the
wall should be more than 2 cm.
2-2. CONNECTING WATER SUPPLY HOSE
6
Before connecting Water Supply Hose to water tap, check your hose type and choose
correct instruction. Water Supply Hose may vary according to the country.
Make sure connect blue inlet hose to cold water tab, and orange inlet hose to hot water tab.
correct instruction. Water Supply Hose may vary according to the country.
Make sure connect blue inlet hose to cold water tab, and orange inlet hose to hot water tab.
Connecting Water Supply Hose to water tap
Rubber packing
Water supply hose
Connector
Untighten the screw
Untighten the screw of the connector so
that the tap can be placed in the middle.
that the tap can be placed in the middle.
Fixing the connector to the tap
Push the upper connector up till the
rubber packing is in tight contact with the
tap. Then tighten the 4 screws.
rubber packing is in tight contact with the
tap. Then tighten the 4 screws.
Attach the water supply hose to the connector
Push the water supply hose vertically
upwards so that the rubber seal within the
hose can adhere completely to the tap.
upwards so that the rubber seal within the
hose can adhere completely to the tap.
Check the connection of water supply hose and
the connector
the connector
After connecting the hose, open the tap
to check for any water leakage.
In case of water leakage, close the tap
and start again from step 1
to check for any water leakage.
In case of water leakage, close the tap
and start again from step 1
Fixing the connector of connector and water
supply hose
supply hose
Attach the water supply hose to the
connector and then tighten it by screwing
it to the right.
connector and then tighten it by screwing
it to the right.
Normal Type
Normal tab without thread & screw type inlet hose.)
1
2
3
4
5
7
Rubber packing
Screw
Fixed sticker
Rubber packing
Guide plate
Connector
Connector
Fixed sticker
Middle
Connector
Connector
Middle
Connector
Connector
Water Supply Hose
Pressing rod
Pressing handle
Connector
Middle
connector
connector
Fixed Stiicker
Pressing Handle
Pressing Rod
Water Supply Hose
Separate Middle connector from Water
Supply Hose
Supply Hose
Separate Middle connector from the Water Supply
Hose by pulling the Pressing Rod and the Pressing
Handle that is attached to the Water Supply Hose
while pressing them.
Hose by pulling the Pressing Rod and the Pressing
Handle that is attached to the Water Supply Hose
while pressing them.
Loosen the fixed nuts to connect the connector to the tap
Untighten the screw of the connector so that the
tap can be placed in the middle.
tap can be placed in the middle.
Fixing Connectors to the Tap
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.
packing is in tight contact with the tap. Then
tighten the 4 screws.
Fixing Upper Connector and Middle
Connector
Connector
Remove the fixed sticker in between the Upper
and Middle Connectors. Tighten the connectors
by holding one connector and twist middle
connector to the right.
and Middle Connectors. Tighten the connectors
by holding one connector and twist middle
connector to the right.
Connecting Middle Connector and
Water Supply Hose
Water Supply Hose
Press down the pressing rod of the Water
Supply Hose which was separated from middle
connector(refer to Step1) and then join it to the
middle connector.
Supply Hose which was separated from middle
connector(refer to Step1) and then join it to the
middle connector.
One Touch Type
If the tap diameter is too large or is square, open
the 4 screw and take out the guide plate and
follow step 1.
the 4 screw and take out the guide plate and
follow step 1.
In case the tap is large.
Note
Checking the water leakage
After connecting the hose, open the tap to check for
any water leakage.
In case of water leakage, close the tap and start again
from step 1.
If you skip step1, it may cause water leakage.
any water leakage.
In case of water leakage, close the tap and start again
from step 1.
If you skip step1, it may cause water leakage.
(NORMAL TAB WITHOUY THREAD & ONE TOUCH TYPE INLET HOSE.)
1
2
3
4
5
6
Click on the first or last page to see other T1001TEPT service manuals if exist.