LG SW6D2 Service Manual ▷ View online
-9-
4-3. Spin Motor Replacement
After removing the back cover, opening the spin dryer
cover, and removing the spin dryer basket, proceed
as follows:
cover, and removing the spin dryer basket, proceed
as follows:
1. Disconnect the brake strap assembly from the
brake wire assembly.
(Fig.20).
2. Remove the brake wire holder-A in the direction of
the arrow.
(Fig.21).
9. Remove the screws fastening the vibration damper
assemblies and remove the vibration damper
assemblies. (Fig.25).
assemblies. (Fig.25).
8. Keep placing the brake spring portion lower, and
remove the spin motor. (Fig.24).
3. Take out the brake wire assembly from the brake
assembly.
(Fig.22)
4. Disconnect the lead wires.
5. Lay the washing machine on its front side on a
5. Lay the washing machine on its front side on a
blanket or cardboard.
6. Hold the spin mot
or and remove the three hooks
from the base. (Fig.23).
7. Remove the spin motor.
Fig.23
Fig.20
Fig.24
Fig.21
Fig.25
Fig.22
-10-
Fig.30
10. Loosen the fixing bolt fastening the motor shaft
and pull up the coupling assembly
(Fig.26).
2. Disconnect the lead wires.
3. Lay the washing machine on its front side on a
3. Lay the washing machine on its front side on a
blanket or cardboard.
4. Remove the screws fastening the base. (Fig.29).
5. Remove the screws and the washers, remove the
wash motor and remove the wash motor damper.
(Fig.30).
(Fig.30).
6. Loosen the socket bolt of the motor pulley
assembly and pull up the motor pulley assembly
from the motor.
from the motor.
To assemble the wash motor, reverse disassembly
procedure.
procedure.
11. Remove the screws fastening the brake assembly
and remove the brake assembly
(Fig.27).
To assemble the spin motor, reverse the disassembly
procedure.
procedure.
4-4. Wash Motor Replacement
After removing the back cover, proceed as follows:
1. Remove the V-belt from the pulsator pulley
(Fig.28).
Fig.28
Fig.31
Fig.
27
Fig.
26
Fig.
29
-11-
4-5.
Washing Tub Assembly
R
eplacement
After removing the panel assembly, the safety cover
assembly, the spin dryer basket assembly, the spin
dryer cover, the washing cover, the Q-spring, the
nozzle case, the door switch and the back cover,
proceed as follows:
1. Disconnect the drain hose(WP-710N/WP-720N)
or the drainhose-D (WP-710NP/WP-720NP).
2. Remove the V-belt from the pulsator pulley
(Fig.32).
4-6. Gear Case Assembly
Replacement
1. Open the washing cover and loosen the pulsator
fixing screw and pull up and remove the pulsator.
(Fig.34).
Apply adhesive on hose joint to prevent water leaks.
Fig.36
3. Remove the screws fastening the washing tub
assembly and pull it out. (Fig.33)
To assemble the washing tub assembly, reverse the
disassembly procedure.
NOTE
Fig.32
Fig.33
Fig.34
2. Remove the V-belt (Fig.35).
Fig.35
3. Lay the washing machine on its front side on a
blanket or some cardboard.
4. Unscrew and remove the screws fastening the
base
and remove the base assembly. (Fig.36)
-12-
5. Unscrew the pulsator pulley fixing bolt and remove
the pulsator pulley. (Fig.37)
6. Unscrew and remove the screws fastening the gear
case assembly at the tub(Fig.38).
After removing the spin dryer basket assembly, refer
to the figures and proceed as follows:
1. Remove the bellows assembly
1. Remove the bellows assembly
(Fig.40).
2. Remove the bellows supporter by using slip joint
pliers to the spin tub bottom
(Fig.40).
The assembly procedure is as follows:
1. Insert the bellows assembly into the bellows
1. Insert the bellows assembly into the bellows
supporter.
2. Fit them by pushing the bellows assembly and the
bellows supporter at the same time in the spin tub
bottom
(Fig.41).
3. Pass the spin shaft through the center hole of the
bellows assembly and insert it into the coupling
assembly
(Fig.41).
NOTE
1. Don't disassemble four screws fixing the
gear case
assembly.
2. Check the assembled condition of the
packing-P at
the tub hole is right when youassembled the gear
case assembly. (Fig.39)
The bellows assembly attached to the unit
cannot be removed unless it is torn off.
NOTE
NOTE
NOTE
Tub
Packing-P
Gear case
Tub
Packing-P
Gear case
Tub
Packing-P
Gear case
Tub
Packing-P
Gear case
Tub
Packing-P
Gear case
Tub
Packing-P
Gear case
Tub
Packing-P
Gear case
Tub
Packing-P
Gear case
4-7. Bellows Assembly Replacement
Fig.37
F
ig.38
Fig. 39
Fig.4
0
Fig. 41
NOTE
NOTE
Click on the first or last page to see other SW6D2 service manuals if exist.