LG SW6D2 Service Manual ▷ View online
-7-
To assemble the drain select arm to the switchbody,
reverse the disassembly procedure.
Fig.12
Fig.13
7. Remove the panel base assembly. (Fig.7).
Drain Select Arm Replacement
1. Pull out the knob for the drain selector.
2. Disconnect the plunger valve strap from the drain
select arm (Fig.12).
3. Lift the drain select arm in the direction of arrow and
at the same time rotate the drain select arm in the
direction of the white arrow until the hook of the drain
select arm matches the groove of the switch body.
To assemble the panel assembly, reverse the
disassembly procedure.
Timer Replacement
1. Disconnect the lead wires of the timers
2. Pull out the knob. (Fig.8)
3. Remove the screws fastening the switch body
and remove the switch body. (Fig.9).
Fig.
7
Fig.
10
Fig.8
NOTE
• When replacing the panel
base assembly,
fix the plunger valve strap properly.
• Securely solder connecting lead wires , or used
connectors and insulate
w
ell to prevent
Fig.9
Spin timer
Wash timer
4. Remove the timer by pushing the claw holding the
timer in the direction of the arrow.
Fig.
11
To assemble the timers to the switch body, reverse
the disassembly procedure.
overheating.
-8-
3. Pull out completely the spin dryer basket
assembly. (Fig.19)
Fig.14
To assemble the spin dryer basket assembly,
reverse the disassembly procedure.
Mini Switch Replacement
(WP-710NP/WP-720NP)
4-2. Spin Dryer Basket
Assembly Replacement
1. Set the knop for the drain selector to
“WASH &RINCE” or “DRAIN” or “OFF”
2. Disconnect the lead wires of the mini switch.
3. Remove the screw fastening the mini switch and
remove the mini switch. (Fig.14).
To assemble the mini switch to the switch body,
reverse the disassembly procedure.
To assemble the spin dryer cover assembly,
reverse the disassembly procedure.
After removing the back cover, proceed as follows:
1. Open the spin dryer cover and the safety cover-2
and pull up and remove the safety cover-1.
(Fig.17)
After removing the safety cover-1, the safety cover-2,
the panel assembly, proced as follows:
Spin Dryer Cover
Fig.17
Fig.18
Fig.15
Fig.19
Fig.16
1. Remove the Q-spring (Fig.15).
2. Remove the screw fastening the door switch and
remove the door switch (Fig.15).
3. Remove the spin dryer cover by widening
between the hinge hole of the tub and the hinge
of the spin dryer cover and pulling up the spin
2. Loosen the fixing bolt of the coupling assembly
fastening the spin shaft(Fig. 18).
dryer cover (Fig.16).
-9-
4-3. Spin Motor Replacement
After removing the back cover, opening the spin dryer
cover, and removing the spin dryer basket, proceed
as follows:
cover, and removing the spin dryer basket, proceed
as follows:
1. Disconnect the brake strap assembly from the
brake wire assembly.
(Fig.20).
2. Remove the brake wire holder-A in the direction of
the arrow.
(Fig.21).
9. Remove the screws fastening the vibration damper
assemblies and remove the vibration damper
assemblies. (Fig.25).
assemblies. (Fig.25).
8. Keep placing the brake spring portion lower, and
remove the spin motor. (Fig.24).
3. Take out the brake wire assembly from the brake
assembly.
(Fig.22)
4. Disconnect the lead wires.
5. Lay the washing machine on its front side on a
5. Lay the washing machine on its front side on a
blanket or cardboard.
6. Hold the spin mot
or and remove the three hooks
from the base. (Fig.23).
7. Remove the spin motor.
Fig.23
Fig.20
Fig.24
Fig.21
Fig.25
Fig.22
-10-
Fig.30
10. Loosen the fixing bolt fastening the motor shaft
and pull up the coupling assembly
(Fig.26).
2. Disconnect the lead wires.
3. Lay the washing machine on its front side on a
3. Lay the washing machine on its front side on a
blanket or cardboard.
4. Remove the screws fastening the base. (Fig.29).
5. Remove the screws and the washers, remove the
wash motor and remove the wash motor damper.
(Fig.30).
(Fig.30).
6. Loosen the socket bolt of the motor pulley
assembly and pull up the motor pulley assembly
from the motor.
from the motor.
To assemble the wash motor, reverse disassembly
procedure.
procedure.
11. Remove the screws fastening the brake assembly
and remove the brake assembly
(Fig.27).
To assemble the spin motor, reverse the disassembly
procedure.
procedure.
4-4. Wash Motor Replacement
After removing the back cover, proceed as follows:
1. Remove the V-belt from the pulsator pulley
(Fig.28).
Fig.28
Fig.31
Fig.
27
Fig.
26
Fig.
29
Click on the first or last page to see other SW6D2 service manuals if exist.