DOWNLOAD LG SP105 Service Manual ↓ Size: 5.66 MB | Pages: 45 in PDF or view online for FREE

Model
SP105
Pages
45
Size
5.66 MB
Type
PDF
Document
Service Manual
Brand
Device
Washing Machine
File
sp105.pdf
Date

LG SP105 Service Manual ▷ View online

6
3-2. WATER LEVEL CONTROL
This model incorporates a pressure sensor which can sense the water level in the tub.
The water supply is stopped when the water level reaches the preset level; then the selected cycle begins.
Spinning does not proceed until the water in the tub drains to a certain level.
3-3. DOOR CONTROL
The door can be opened by pulling the door handle whenever washer is not in operation.
When the cycle is completed, the DOOR LOCKED light will turn off.
If a power failure has occurred while in operation, the door will unlock after 2 minutes.
Clicking sounds can be heard when the door is locked/unlocked.
3-4. THE DOOR CAN NOT BE OPENED
While program is operating.
While Door Lock lights turn on.
While the drum is rotating.
3-5. DOOR LOCKED LAMP LIGHTS
When the frequency of water level is lower than 22.9 kHz.
(It can be canceled when the frequency is more than 23.8 kHz.) 
When the temperature inside the tub is higher than 45° C (104° F) and water level is not 25.5 kHz.
(It can be canceled when the water level is 25.5 kHz or the temperature inside the tub is lower than 
40° C (113° F). )
7
4. PARTS IDENTIFICATION
Drain Hose
Dispenser
Door
Lower Cover Cap
Drain Plug
Drain Pump Filter
Adjustable Feet
Power Plug
Control Panel
Shipping Bolts (4)
Drain
Cold Water Inlet
Hot Water Inlet
Air Vent for Safety
If the supply cord is damaged,
it must be replaced by the
manufacturer or an authorized
service technician in order to
avoid a hazard.
Name:
Front-loading Washing Machine
Power supply:
220V~ 50Hz
)
n
e
p
o
 r
o
o
d
 
h
ti
w
 
D
m
c
 
1
.
9
2
1
 ,
)
H
m
c
 
3
.
8
9
 
X
 )
D
m
c
 
6
.
5
7
 
X
 )
W
m
c
 
6
.
8
6
:
e
z
i
S
27 (W) X 29
3/4
(D) X 38
11
/
16
(H), 50
13
/
16
(D with door open)
Weight:
190 lbs. (86 kg)
Wash capacity:
15kg
Spin speed:
1000 rpm max.
Permissible water pressure: 14.5~116 psi (100~800 kPa) 
Back of Washer
Specifications subject to change by manufacturer.
Note
Accessories
Hot/Cold (1each)
Hose
Wrench
Tie strap
to secure drain hose to standpipe
inlet hose, or laundry tub
8
5. INSTALLATION INSTRUCTIONS
Unscrew the 4 bolts with the wrench supplied
Take out the 4 bolts by twisting the braces slightly
Keep the 4 bolts and the wrench for future use
(Whenever the appliance is transported, the
shipping bolts and braces must be replaced.)
Close the holes with the caps supplied.
The appliance is fitted with shipping bolts to prevent
internal damage during transportation.
Packing and all shipping bolts must be removed
before using the washer.
When unpacking the base, be sure to remove
the additional packing support in the middle of
the base packing.
Shipping bolts
• Washer is heavy. Two or more people may be needed to install and move the appliance.
Failure to do so can result in back or other injury.
• Store and install the washer where it will not be exposed to temperatures below freezing or exposed to
outdoor weather conditions. Failure to follow this warning can cause serious injury, fire, electrical shock, or
death.
• This appliance must be properly grounded for personal safety. Properly ground washer to conform with all
governing codes and ordinances. Failure to follow this warning can cause serious injury, fire, electrical shock,
or death.
• Do not install the washer in humid spaces to reduce the risk of electric shock. Failure to follow this
warning can cause serious injury, fire, electrical shock or death.
• The base opening must not be obstructed by carpeting when the washer is installed on a carpeted floor. 
• Do not remove ground prong. Do not use an adapter or extension cord. Plug into a grounded 3 prong outlet.
Failure to follow this warning can cause serious injury, fire, electrical shock or death.
Removing shipping bolts
Wrench
CAP
!
WARNING
9
Installation clearances
The location must be large enough to open 
the washer door completely. 
Washer dimensions
The following dimensions shown are for the minimum
spacing allowed.
Additional spacing should be considered for
installation and servicing.
• Additional clearances might be required for wall,
door, and floor moldings.
• Additional spacing of 4 (10 cm) on back, 
1 (2.5 cm) on all sides of the washer is
recommended to reduce noise transfer.
Companion appliance spacing should also be
considered.
Minimum installation spacing for
recessed area installation.
Front view
Side view
29 
3
/
4
"
(75.6 cm)
4"
(10 cm)
27"
(68.6 cm
)
29 
3/4
"
(75.6 cm)
38
11/16
"
(98.3 cm)
50 
13/16
"
(129.1 cm
)
27"
(68.6 cm)
1"
(2.5 cm)
1"
(2.5 cm)
Page of 45
Display

Click on the first or last page to see other SP105 service manuals if exist.