DOWNLOAD LG LV1550111 Service Manual ↓ Size: 17.97 MB | Pages: 45 in PDF or view online for FREE

16

Program Chart

Blanket

Bulky

Spin

Boiling Care

Cotton Quick

2

40

1:10

1

45

16

2:36

1:21

1:32

1:15

15

7-4. ERROR DISPLAY

If you press the [Start/Pause] button when an error in displayed, any error except software ERROR will
disappear and the machine will change into pause status.
In case of        ,        ,        , if the error is not resolved within 15 sec. In case of other errors, if the
error is not resolved within 4 min. Power will be turned off automatically and the error only will be
blinked. But in the case of       , power will not be turned off.

WATER 

I

NLET

E

RROR

Water has not reached to the pre-set level within 4 min.
since inlet valve operated, or water has not reached to
the normal level within 25 min. 

Page 

19

1

U

NBALANCED 

E

RROR

2

WATER 

O

UTLET

E

RROR

3

OVER

F

LOW 

E

RROR

4

The appliance is tilted.

Laundry is gathered to one side.

Non distributable things are put into the drum.

Page 2

0

Water has not drained enough within 8 min.

Page 2

1

Water is automatically being pumped out because too
amuch water is in the tub.

Page 2

3

P

RESSURE SENSOR

S/W 

E

RROR

5

The sensor pressure switch is out of order.

Page 2

4

D

OOR OPEN 

E

RROR

6

The [Start/Pause] button is pressed with the door open.

The door switch is out of order.

Page 2

5

T

HERMISTOR(HEATING)

E

RROR

7

The thermistor is out of order. 

Page 2

6

P

OWER

F

AILURE

10

The washer experienced a power failure.

C

URRENT

E

RROR

8

PWB ASSEMBLY (Main) is out of order

Replace the PWB assembly (Main)

Winding in the MOTOR is short-circuited.

Replace the MOTOR

MOTOR

L

OCKED 

E

RROR

9

The Connector (3-pin, male, white) in the wire harness
is not connected to the Connector (3-pin, female, white)
of MOTOR.

Reconnect or repair the connector

The electric contact between the connectors [3-pin,
male, white in the wire harness and 6-pin, female, white
in the PWB ASSEMBLY (Main]) is bad or unstable.

Reconnect or repair the contact in the connector

The wire harness between the MOTOR and PWB
ASSEMBLY (Main) is cut (open circuited).
The hall sensor is out of order/defective.

Page 2

7

7-5. TROUBLESHOOTING WITH ERROR

Water Inlet Error (IE)

Is the water tap closed ?

[Note] Environmental safety check list

1. No water tap leakage & freeze.

2. No entanglement of water supply hose.

5. No the inlet filter clogged.

Check the 

Water tap

and  open it fully .

When there is water in the tub,
is the water level frequency
over 25.5KHz ?

Reconnect or repair the 

Connector

.

Or replace the 

Harness

.

Replace the 

Inlet Valve

.

Is the 

Connector

connected correctly to 

the 

Main PCB

and the 

Inlet Valve

?

Or is the 

Harness

alright ?

Check the 

Air Chamber

and 

the Tube

(clogged) 

And When you check the water level frequency again, 
if it is over 25.5KHz, you replace 

the Pressure switch.

YES

YES

NO

NO

Replace the 

Main PCB

.

NO

YES

YES

NO

NO

Is the each resistance of Inlet Valve within
3.5 ~4.5 kΩ ?

When the washing machine is started, 
is operated the inlet valve? 

Pre. Valve

Main Valve

19

1

2

1

2

3. No water shortage.                           4. No water supply hose leakage