DOWNLOAD LG F92932WH Service Manual ↓ Size: 26.82 MB | Pages: 57 in PDF or view online for FREE

Use spanner to remove transit bolts.

3

Confirm the distance between the appliance and the wall.

4

The tap connection and hose connection must be parallel.

5

Without removal of transit bolts

Spin noise

and

shaking

.

X 4 EA

Transit bolts

More than 2cm

If the distance is less than 2cm,

the water supply hose will

kink

or

fold

.

1. Normal Tap without thread &

screw

type inlet hose.

Unscrew the fixing screw to

attach the tap.

Push the connector up till the

rubber packing is in tight contact

with the tap. Then tighten the 4

screws.

Push the water supply hose

vertically upwards so that the

rubber packing within in the hose

can adhere completely to the tap

and then tighten it by screwing it

to the right.

Untighten the upper connector

screw.

Push the upper connector up

till the rubber packing is in

tight contact with the tap. Then

tighten the 4 screws.

Connect the water supply hose

to the middle connector, pushing

the plate down.

• In case the diameter of the tap

is large remove the guide plate.

• Turn the middle connector not to

have water leaked.

• Make sure that the rubber seal is

inside the hose connector.

• To separate the water supply

hose from the middle connector

shut off the tap.

Then pull the inlet hose down,

pushing the plate down.

• Make sure that there are no

kinks in the hose and that it is

not crushed.

2. Normal Tap without thread &

one touch

type inlet hose (Single inlet models)

Upper

Connector

Fixing screw

Guide plate

Connector

Rubber packing

Upper

Connector

Rubber packing

Upper

Connector

Plate

Water supply

hose

Rubber seal

Hose connector

Upper

Connector

Middle

connector

Rubber

packing

Upper

Connector

Fixing screw

Middle

connector

Rubber

packing

Upper

Connector

Plate

Water supply

hose

Connect Drain Hose.

6

Connect power plug.

7

If the drain hose is not installed properly, the unit will not drain properly.
This allows water to back flow into the unit which can cause odors.
Refer to Owner Manual for proper drain hose installation.
The odor could also be coming from the home’s drain to which the drain hose is attached.

In this type of drain hose installation, the odor could be coming from the standpipe.
This odor can come up the drain hose and into the unit.
Pour a cup or two of bleach or vinegar down the home drain 
and let it sit for 24 hours before running another cycle.
This will help eliminate odor from the home drain. 
If a cycle is started too soon after doing this, it will not help the issue.

Connect the power plug to the wall outlet.

Avoid connecting several electric devices, 
it may be the cause of a fire.

about 100 cm

about 145 cm

about 105 cm

Laundry tub

Max. 100cm

min. 60cm

Max. 100cm

min. 60cm

Retainer

Tie

strap

Hose

min. 60 cm

max. 100 cm

Rubber Cup

Check the horizontality with a level (Gage).

8

If washing machine legs are loose or not Screwed in, then 

with the spanner wrench. 

Using the level, level the washing machine from front to back and side to side.

Use the spanner wrench to adjust Legs until level and try the 

.

Perform a Rinse and Spin with some clothing in the machine.
To do this, put 2~3kg of clothing in the unit, turn on the unit, Select the Rinse+Spin 
and then start. When the unit reaches the spin cycle, watch for vibrations.
If the unit is vibrating, make small adjustments to the leg until they subside. (Repeat step 2)

the lock nut against the base of the machine to 

the 

.

Lower the foot until there is no gap between floor and foot.
And only use 

when difference at the leg adjustment is more than 

.

Place your right hand on the back, right corner and your left hand on the front,
left corner of the unit, then attempt to rock the unit from corner to corner.
Then, move your right hand to the front, right side and your left hand to the
back, left corner and attempt to rock the unit from corner to corner.
If the unit is level, it will not rock.  However, if the unit is not level, it will rock.
If the unit rocks, it will be necessary to adjust the leveling feet of the unit.
Adjust the foot under the hand that is on the front of the machine.

A level

Higher

Tighten

Adjustable feet

Tighten

Adjustable feet

Higher

Tighten

Adjustable feet

Lower

4620ER4002B
(Gray)

for Wooden floors

Rubber Cup

4620ER4002A
(Black)

for Tile floors

Lock nut

10mm

Adjustable bolt

Tighen the lock nut

Floor

No Gap

Floor

No Gap

Floor

Gap

Test operation

9

Preparation
for 
washing.

· Connect the power plug to the

outlet.

· Connect the inlet hose.   

Press the power button.

Press the START/PAUSE
button.

Check the water heating.

· Press the  left Option + temp

button simultaneously and the
present temperature will be
displayed. 

Page 20

· Check if the drum rotates

clockwise and  counterclockwise. 

Check automatic reverse turn.

Check the water supply.

· Check if water is supplied through

the detergent dispenser.

Check the drain and spin
functions.

· Turn power off and then power on.
· Select the spin rpm
· Press the START PAUSE button.
· Check the spin and drain

functions.

· Turn power off and then power on.
· Listen for a click to determine if the

door is unlocking.

Turn power off and open
the door.

Water removal.

· If SVC is needed during  check,

remove the remaining water by
pulling out the hose cap.

· In case of Coloreds program.