DOWNLOAD LG F8068QDP2 Service Manual ↓ Size: 8.4 MB | Pages: 52 in PDF or view online for FREE

7-4. ERROR DISPLAY

If you press the [Start/Pause] button when an error in displayed, any error except software ERROR will
disappear and the machine will change into pause status.
In case of        ,        ,        , if the error is not resolved within 15 sec. In case of other errors, if the
error is not resolved within 4 min. Power will be turned off automatically and the error only will be
blinked. But in the case of       , power will not be turned off.

WATER 

I

NLET

E

RROR

Water has not reached to the pre-set level within 4 min.
since inlet valve operated, or water has not reached to
the normal level within 25 min. 

Page 21

1

U

NBALANCED 

E

RROR

2

WATER 

O

UTLET

E

RROR

3

OVER

F

LOW 

E

RROR

4

The appliance is tilted.

Laundry is gathered to one side.

Non distributable things are put into the drum.

Page 22

Water has not drained enough within 8 min.

Page 23

Water is automatically being pumped out because too
amuch water is in the tub.

Page 25

P

RESSURE SENSOR

S/W 

E

RROR

5

The sensor pressure switch is out of order.

Page 26

D

OOR OPEN 

E

RROR

6

The [Start/Pause] button is pressed with the door open.

The door switch is out of order.

Page 27

T

HERMISTOR(HEATING)

E

RROR

7

The thermistor is out of order. 

Page 28

P

OWER

F

AILURE

10

The washer experienced a power failure.

C

URRENT

E

RROR

8

PWB ASSEMBLY (Main) is out of order

Replace the PWB assembly (Main)

Winding in the MOTOR is short-circuited.

Replace the MOTOR

MOTOR

L

OCKED 

E

RROR

9

The Connector (3-pin, male, white) in the wire harness
is not connected to the Connector (3-pin, female, white)
of MOTOR.

Reconnect or repair the connector

The electric contact between the connectors [3-pin,
male, white in the wire harness and 6-pin, female, white
in the PWB ASSEMBLY (Main]) is bad or unstable.

Reconnect or repair the contact in the connector

The wire harness between the MOTOR and PWB
ASSEMBLY (Main) is cut (open circuited).
The hall sensor is out of order/defective.

Page 29

• Load is too small.
• Load is out of balance.
• The appliance has an imbalance detection

and correction system. If individual heavy
articles are loaded (ex. bath mat, bath robe,
etc.) this system may stop spinning or even
interrupt the spin cycle altogether.

• If the laundry is still too wet at the end of the

cycle, add smaller articles of laundry to
balance the load and repeat the spin cycle.

• Water supply is not adequate in area.
• Water supply taps are not completely open.
• Water inlet hose(s) are kinked.
• The filter of the inlet hose(s) are clogged.

Check another tap in the house.
Fully open tap.
Straighten hose(s).
Check the filter of the inlet hose.

Clean and straighten the drain hose.
Clean the drain filter.

Add 1 or 2 similar items to help 
balance the load.
Rearrange load to allow proper 
spinning

Close the door.
If it is not released, call for service.

Unplug the power plug and call for 
service.

Close the water tap.
Unplug the power plug.
Call for service.

• Drain hose is kinked or clogged.
• The drain filter is clogged.

• Is the door opened?

• Water overfills due to the faulty water valve.

• Water level sensor has malfunctioned.

24

F**68*D(P)

25

Close the water tap.
Unplug the power plug.
Call for service.

• Over load in motor.

• Over load in motor.

25

26

7-5. TROUBLESHOOTING WITH ERROR

Is the water tap closed?

[Note] Environmental safety check list

1. No water tap leakage & freeze.

2. No entanglement of water supply hose.

3. No water shortage.

4. No water supply hose leakage.

5. No the inlet filter clogged.

Check the 

and  open it fully.

When there is water in the tub,

is the water level frequency

over 25.5KHz?

Reconnect or repair the 

.

Or replace the 

.

Replace the 

.

Is the 

connected correctly to 

the 

and the 

?

Or is the 

alright ?

Check the 

and 

(clogged) 

And When you check the water level frequency again, 

if it is over 25.5KHz, you replace 

Replace the 

.

Is the each resistance of Inlet Valve within

3.5 ~4.5 kΩ ?

When the washing machine is started, 

is operated the inlet valve? 

Pre. Valve

Main Valve

1

2

1

2

27