LG F24953WHS Service Manual ▷ View online
11
Connect Drain Hose.
6
Connect power plug.
7
If the drain hose is not installed properly, the unit will not drain properly.
This allows water to flow back into the unit which can cause odors.
Refer to owner’s manual for proper drain hose installation.
The odor could also be coming from the home’s drain to which the drain hose is attached.
This allows water to flow back into the unit which can cause odors.
Refer to owner’s manual for proper drain hose installation.
The odor could also be coming from the home’s drain to which the drain hose is attached.
In this type of drain hose installation, the odor could be coming from the standpipe.
This odor can come up the drain hose and into the unit.
Pour a cup or two of bleach or vinegar down the home drain
and let it sit for 24 hours before running another cycle.
This will help eliminate odor from the home drain.
If a cycle is started too soon after doing this, it will not help the issue.
This odor can come up the drain hose and into the unit.
Pour a cup or two of bleach or vinegar down the home drain
and let it sit for 24 hours before running another cycle.
This will help eliminate odor from the home drain.
If a cycle is started too soon after doing this, it will not help the issue.
Connect the power plug to the wall outlet.
Avoid connecting several electric devices,
it may be the cause of a fire.
it may be the cause of a fire.
about 100 cm
about 145 cm
about 105 cm
Laundry tub
Max. 100cm
Max. 100cm
Retainer
Tie
strap
Hose
max. 100 cm
12
12
Check the horizontality with a level (Gage).
8
Step 1
If washing machine legs are loose or not fully attached, then
tighten
with the spanner wrench.
Using the level, level the washing machine from front to back and side to side.
Step 2
Use the spanner wrench to adjust legs until level and try the
Diagonal test
.
Step 3
Perform a Rinse and Spin with some clothing in the machine.
To do this, put 2~3kg of clothing in the unit, turn on the unit, select the Rinse+Spin
and then start. When the unit reaches the spin cycle, check vibrations.
If the unit vibrates, adjust the leveling foot slightly until the vibration subside. (Repeat step 2)
and then start. When the unit reaches the spin cycle, check vibrations.
If the unit vibrates, adjust the leveling foot slightly until the vibration subside. (Repeat step 2)
Step 4
Tighten
the lock nut up to
lock
the
positioned leg
.
Lower the foot until there is no gap between floor and foot.
And only use
And only use
adjustment rubber
when the gap is more than
10mm
.
Place your right hand on the back, right corner and your left hand on the front,
left corner of the unit, then attempt to rock the unit from corner to corner.
Then, move your right hand to the front, right corner and your left hand to the
back, left corner and attempt to rock the unit from corner to corner.
left corner of the unit, then attempt to rock the unit from corner to corner.
Then, move your right hand to the front, right corner and your left hand to the
back, left corner and attempt to rock the unit from corner to corner.
If the unit is level, it will not rock. However, if the unit is not level, it will rock.
If the unit rocks, it will be necessary to adjust the leveling feet of the unit.
Adjust the foot on the front right corner.
If the unit rocks, it will be necessary to adjust the leveling feet of the unit.
Adjust the foot on the front right corner.
How to perform a diagonal test:
A level
Lower
Tighten
Adjustable feet
Diagonal test
Loosen
Adjustable feet
Higher
Tighten
Adjustable feet
Lower
4620ER4002B
(Gray)
(Gray)
for Wooden floors
Rubber Cup
4620ER4002A
(Black)
(Black)
for Tile floors
Lock nut
10mm
Adjustable bolt
Tighen the lock nut
Floor
No Gap
Floor
No Gap
Floor
Gap
13
Test operation
9
1
Preparation
for
washing.
for
washing.
· Connect the power plug to the
outlet.
· Connect the inlet hose.
2
Press the power button.
3
Press the START/PAUSE
button.
button.
6
Check the water heating.
· Touch the Temp. and Pre
Wash button simultaneously
to check the present
temperature.
to check the present
temperature.
Page 22
· Check if the drum rotates
clockwise and counterclockwise.
5
Check automatic reverse turn.
4
Check the water supply.
· Check if water is supplied through
the detergent dispenser.
7
Check the drain and spin
functions.
functions.
· Turn power off and then power on.
· Select the spin rpm
· Press the START PAUSE button.
· Check the spin and drain
· Select the spin rpm
· Press the START PAUSE button.
· Check the spin and drain
functions.
· Turn power off and then power on.
· Listen for a click to determine if the
· Listen for a click to determine if the
door is unlocking.
8
Turn power off and open
the door.
the door.
9
Water removal.
· If SVC is needed during check,
remove the remaining water by
pulling out the hose cap.
pulling out the hose cap.
· In case of Coloreds program.
14
Rotate the
to select the cycle
designed for different
types of fabric and soil
levels.
Use this button to Start/
Pause the washe
r.
Time Delay : Allows the start of any cycle to be delayed
for 3~19 hours.
Steam Wash : By pressing the Steam Wash button, if Steam
Function is selected, the Steam Wash button will light up.
Favorite : Favorite program allows you to store a
customized wash cycle for future use.
Pre Wash : Use
this option for load that needs protreatment.
Adds 19minutes pre wash and drain.
Medic Rinse : For best results or for cleaner rinsing, you can choose
Medic Rinse option
Rinse + Spin : This can be helpful in preventing fresh stains from setting
in fabrics.
Time Save : This option can be used to reduce the time of a wash program.
To use this option press option button before wash program is started.
Intensive : If the laundry is heavily soiled, intensive option is effective.
Cycle Sele ctor
Additional programs
Start/ Pause
Option Button
Use this button to turn the
power
.
Power
5. OPERATION (F1495BDS(1~9))
Click on the first or last page to see other F24953WHS service manuals if exist.