DOWNLOAD LG F14A8YD / F14A8YD6 Service Manual ↓ Size: 14.64 MB | Pages: 60 in PDF or view online for FREE

Model
F14A8YD F14A8YD6
Pages
60
Size
14.64 MB
Type
PDF
Document
Service Manual
Brand
Device
Washing Machine
File
f14a8yd-f14a8yd6.pdf
Date

LG F14A8YD / F14A8YD6 Service Manual ▷ View online

7
3. PARTS IDENTIFICATION
Drawer
Drum
Door
Drain Hose
Adjustable Feet 
Transit Bolts
Control Panel
Power Plug
Drain Pump Filter
Drain Plug
Lower Cover Cap
If the supply cord is damaged,
it must be replaced by the
manufacturer or its authorized
service technician in order to
avoid a hazard.
ACCESSORIES 
Inlet hose(1EA)         Option : Hot / Cold(2EA)
Spanner
8
4. INSTALLATION
INSTALLATION
The appliance should be installed as follows.
Check the conditions of installation area.
1. Check level ground.
On raised foundations or upper level homes, the 
vibrations
can be caused by the type of flooring. 
It may be 
necessary to move
the 
machine
to a different area in the home or have the floor
reinforced to properly support the operation of the unit.
2. Check for humidity or any foreign objects under the feet.
Clean the floor, there should be no foreign objects under the feet.
If the unit has foreign objects underneath the feet, this will prevent the unit from being leveled properly 
and will cause 
vibrations
and 
slipping
.
Remove any foreign objects
, if any from underneath the machine and level unit properly.
See below for examples of foreign objects.
1
Open the box and check appliance condition.
2
horizontal
Carpet
Paper
Laminated
paper
Purchased
stopper
Base Packing
Washer
Spanner
This leveling (or spanner) wrench must
be used to remove the transit bolts
and level the unit. This should be kept
for future use.
9
Use spanner to remove transit bolts.
3
Confirm the distance between the appliance and the wall.
4
The tap connection and hose connection must be parallel.
5
Without removal of transit bolts
 
and
.
X 4 EA
Transit bolts
More than 2cm
If the distance is less than 2cm,
the water supply hose will
or
.
1. Unscrew the adapter ring plate and the 4 adapter retaining screws.
2. Push the adapter onto the end of the tap so that the rubber seal forms
a watertight connection. Tighten the adapter ring plate and the 4
screws.
3. Push the water supply hose vertically upwards so that the rubber
packing within in the hose can adhere completely to the tap and then
tighten it by screwing it to the right.
• Water supply pressure must be between 100 kPa and 1000 kPa (1.0 ~ 10.0 kgf / cm
2
)
• Do not strip or crossthread when connecting Inlet hose to the valve.
• If the water supply pressure is more than 1000 kPa, a decompression device should be installed.
• Periodically check the condition of the hose and replace the hose if necessary.
Type-A : Connecting Screw-type hose to tap with thread
• Screw the hose connector onto water supply tap.
Connecting water supply hose
Step1 : Check rubber seal inlet hose
Step2 : Connect hose to water tap
• Two rubber seals are supplied with the water inlet hoses. 
They are used for preventing water leaks. Make sure the connection to
taps are sufficiently tight.
Upper
connector
Rubber
packing
Plate
Water supply
hose
Fixing screw
Hose
connector
Rubber
seal
Type-B : Connecting Screw-type hose to tap without thread
10
Please use the horizontal tap
Horizontal tap
Extension tap
Square tap
1. Unscrew the adapter ring plate and the 4 adapter retaining
screws.
2. Remove the guide plate if the tap is too large to fit the
adapter.
3. Push the adapter onto the end of the tap so that the rubber
seal forms a watertight connection. 
Tighten the adapter ring plate and the 4 screws.
4. Pull the connector latch plate down, push the inlet hose onto
the adapter, and release the connector latch plate. 
Make sure the adapter locks into place.
Ring plate
Guide plate
Latch plate
Type-C : Connecting one touch type hose to tap without thread
Step3: Connect hose to washer
• Make sure that there are no kinks in the hose and that they are not
crushed.
When your washer has two valves.
• The Inlet hose With the red connector is for the hot water tap.
• If the washer has two valves, energy is saved by  using the hot valve.
NOTE
After connecting inlet hose to water tap, turn on the water taps
to flush out foreign substances (dirt, sand or sawdust) in the
water lines. Let water drain into a bucket, and check the water
temperature.
NOTE
After completing connection, if water leaks from the hose, repeat the same steps. 
Use the most conventional type of faucet for water supply. In case the faucet is square or too big, remove the spacing
ring before inserting the faucet into the adaptor.
Page of 60
Display

Click on the first or last page to see other F14A8YD / F14A8YD6 service manuals if exist.