LG F1481TDP2 Service Manual ▷ View online
29
NO
Is the door closed?
Is the Door assembly in line with door switch ?
Lift up & Close the door.
If the dE is displayed, Replace the
Door Bracket
.
Close the door fully.
YES
YES
Reconnect or repair the
Connector
.
Or replace the
Harness
.
NO
Replace the
Spring
NO
Replace the
Door switch
.
NO
Does the
Spring
of
Latch Hook
actuate?
Door Open Error (dE)
YES
YES
YES
NO
NO
Scratch by Latch Hook
Touching
or
This problem can be repaired very easily.
Just assemble the gasket (door seal).
Has the Gasket fell out??
Is the
Connector
connected correctly to
the
Main PCB
and the
Door Switch
?
Is the
Harness
alright ?
Does the
Door Switch
operate as follows?
* Door Locking time :
1~8
sec.
Check the time between from
input the power to parts
move up, then Door locked.
input the power to parts
move up, then Door locked.
* Door Releasing time :
25~100
sec.
Check the time between from off the
power to parts
move down, then Door released.
power to parts
move down, then Door released.
1
1
1
30
YES
Is the resistance of the
Thermistor
out of range 44 ~
53 KΩ at 25°C? (Page 17)
Replace the
Main PCB
.
Is the
Connector
connected correctly to
the
Main PCB
and the
Thermistor
and the
Heater
?
Is the
Harness
alright ?
Reconnect or repair the
Connector
.
Or replace the
Harness
.
Replace the
Thermistor
.
YES
Replace the
Heater
.
YES
NO
Is the resistance of the
Heater
out of range 24.5 ~
28.5Ω (for Washing) or 42.5 ~ 49.5Ω (for Steam) ?
(Page 19)
(Page 19)
[Note] Thermistor Spec
NO
NO
Thermistor (Heating) Error (tE)
S
P
E
C
Temp
30 °C
40 °C
60 °C
70 °C
95 °C
105 °C
Resistance (kΩ)
MIN
36.35
39.45
42.72
24.20
26.05
27.97
11.43
12.12
12.82
8.088
8.514
8.940
3.544
3.791
4.045
2.617
2.816
3.023
STD
MAX
Heater for Washing
Heater for Steam
31
NO
Are the resistance of the
Hall Sensor
5~15kΩ?
Motor Locked Error (LE)
[Pre Check]
• Gentle wash cycles, such as Perm Press, Delicates, Hand Wash, and Wool/Silk should only be used for smaller loads.
• Gentle wash cycles, such as Perm Press, Delicates, Hand Wash, and Wool/Silk should only be used for smaller loads.
Because these cycles are more gentle in tumbling and spinning, putting too much in the drum can register an issue
with the motor. Remove items, reset unit and test with a Rinse/Spin cycle.
with the motor. Remove items, reset unit and test with a Rinse/Spin cycle.
• Don’t replace the PCB, when the hall sensor is replaced.
Replace the PCB, when the LE is displayed after replacing the hall sensor.
Is the
Connector
connected correctly to
the
Main PCB
and the
Motor
?
Is the
Harness
alright ?
YES
NO
YES
YES
YES
YES
NO
Disassemble the
Rotor
.
Is the
Magnet
of rotor cracked or broken?
• Ha ~ Common
: 5 ~ 15 kΩ
• Hb ~ Common
: 5 ~ 15 kΩ
Replace the
Main PCB
.
Press the
Power
button &
Start / Pause
button.
Does the
Drum
stop when the start/pause button is pressed to start the cycle ?
Or Sometimes does the
Drum
rotate weakly (under 15rpm)?
Magnet
Ha
Hb
Common
Is the resistance the same
between
between
Stator
points?
V~U / U~W / W~V : 8~11Ω
V U W
V U W
Reconnect or repair the
Connector
.
Or replace the
Harness
.
Replace the
Rotor
.
Replace the
Hall Sensor
.
Disassemble
hall sensor carefully.
(Next page)
NO
Replace the
Stator
.
32
Disassemble the Hall Sensor
1) Disassemble the hook of Hall Sensor by (-) driver.
2) Pull up Hall Sensor slowly as shown in picture.
1) Adjust the hole of Hall Sensor to
the hooks of stator as shown in red circle
2) Push down the Hall sensor,
and assemble to the hook securely.
Caution
If you disassemble by force,not following the directions,
the hooks of stator(red circled) might break.
Hence need change of stator assembly.
the hooks of stator(red circled) might break.
Hence need change of stator assembly.
So disassemble cautiously.
1
Assemble the Hall Sensor
2
[Note]
Hall Sensor Part No.
• 24” / 25” : 6501KW2001A
• 24” / 25” : 6501KW2001A
• 27” : 6501KW2002A
Click on the first or last page to see other F1481TDP2 service manuals if exist.