LG F1480YD / F1480YD2 / F1480YD26 / F1480YD5 / F1480YD6 Service Manual ▷ View online
24
Water Outlet Error (OE)
Is the drain hose kinked ?
Check drain hose for kink and straighten the
Hose
.
Drain Hose
Is the
Pump filter
clogged ?
Next Page
Check & Clean
Pump Filter
.
YES
YES
NO
NO
This kind of accumulation on the drain filter not only
prevents proper drainage, but also will promote
bacteria growth and cause odors.
This drain filter should be cleaned once a month.
prevents proper drainage, but also will promote
bacteria growth and cause odors.
This drain filter should be cleaned once a month.
* How to disassemble and clean pump filter
Open the Cover by coin or
finger(only new model)
Cover
Drain water by removing the
hose cap.
Disassemble the pump
filter by turning the filter
cap counterclockwise.
Filter clogged by foreign objects
Assemble & close cap
Pump Filter
filter Cap
Hose Cap
Clean the filter
Filter Cap
25
Is the
Connector
connected correctly to
the
Main PCB
and the
Pump Motor
?
Or is the
Harness
alright ?
Is the
Standpipe Height
greater
than 1.0 m above the floor?
When there is no water in the
pump casing, is the water level
frequency over 26.0khz ?
Observe
Standpipe Height
requirements
of
1.0
m maximum.
- Your washer will not be able to drain out
water adequately, if the standpipe exceeds 1.0 m.
In this case, water may flow back into the washer.
Check the
Air Chamber
and the
Tube
(clogged).
Check the water level frequency again, if it is over
25.5KHz, replace the
If it is clogged, Pressure
switch.
YES
NO
Reconnect or repair the
Connector
.
Or replace the
Harness
.
NO
Replace the
Main PCB
.
NO
Replace the
Pump Motor
.
Is the resistance of the Pump Motor out
of range 152~175Ω?
Or is the Impeller operating normally?
Or is the Impeller operating normally?
Does the Pump motor start, when the spin mode
starts?
Clean the drain hose.
If the drain hose blocked?
Escape
Binding
NO
NO
YES
YES
YES
OR
YES
YES
26
Over Flow Error (FE)
Is the water coming in
drawer ?
drawer ?
Replace the
.
After power off for 10 sec. and power on.
Does the water level over reference line Is
Does the water level over reference line Is
the water level frequency 26.2Khz ?
Or does
the water level over reference line
is the water level frequency 26.2Khz ?
* Water level frequency
- Press and Hold
'Favorite'
&
'Option(Left)'
simultaneously.
Replace the
.
If FE is displayed again,
then replace the
then replace the
.
If FE is displayed again,
then replace the
then replace the
.
Check the
and the
(clogged).
The digits means water level frequency. (10
-1
kHz)
ex) 241 : Water level frequency = 241 x 10
-1
kHz
24.1 kHz
27
Is the air chamber and the tube clogged?
Replace the
Main PCB
.
Is the
Connector
connected correctly to
the
Main PCB
and the
Pressure Switch
?
Is the
Harness
alright ?
Reconnect or repair the
Connector
.
Or replace the
Harness
.
Check air chamber and remove foreign material.
Replace the
Pressure Switch
.
YES
YES
NO
Is the resistance of the
Pressure Switch
out of range?
[Pin1 ~ Pin3]
21~23Ω)
NO
NO
YES
Pressure Sensor S/W Error (PE)
Click on the first or last page to see other F1480YD / F1480YD2 / F1480YD26 / F1480YD5 / F1480YD6 service manuals if exist.