LG F1480TDS / F1480TDS5 / F1480TDS6 Service Manual ▷ View online
48
VALVE (STEAM)
VALVE (PRE-WASH)
VALVE (NORMAL-WASH)
1 Disconnect the wiring connector.
1
1
2
3
2 Remove the valve by two screws of the valve
holder.
• Rating : 220/240V 50/60Hz
• Resistant : 3.5~4.5kΩ
• Resistant : 3.5~4.5kΩ
2
When reconnecting the connector
1 Open the door completely.
2 Remove the three screws from the hinge.
When removing the Door Assembly, it is
necessary to hold the Bracket that is inner of
the Cabinet Cover.
necessary to hold the Bracket that is inner of
the Cabinet Cover.
First, prepare a bucket to put in the remained
water.
water.
Pull it out from hose.
VIOLET/BLACK-BLACK
WHITE/BLACK-BLACK
GRAY/BLACK
INLET VALVE
3
DOOR
Removing method of remained water
CAP(REMAING HOSE)
49
2 Push out PANEL ASSEMBLY, CONTROL after
Push the hook( , ) below.
2
1
1 The plate assembly(Top) is disassembled.
2 Pull out the drawer and unscrew 2 screws.
1 Two screws is unscrewed.
3 Unscrew the screws from the lower cover.
2 Disassembly lower cover assembly.
3 Unscrew the screw from the CABINET COVER.
1
2
3 Lift the side the Control Panel Assembly and
pull it out
CABINET COVER
Two screws are unscrewed
Pull the drawer to arrow direction.
Screws
Disassembly two connector
50
• Just check cut-off.
• Check the operating time.
* Door Locking time :
1~8
sec.
Check the time between from
input the power to parts
move up, then Door locked.
input the power to parts
move up, then Door locked.
* Door Releasing time :
25~100
sec.
Check the time between from off
the power to parts
move down, then Door released.
the power to parts
move down, then Door released.
1
1
1
1
2
4 Lift and separate the cabinet cover.
1 Two screws are unscrewed and disassembly
cabinet cover.
2 The Door Lock S/W is disconnected form the
wiring connector and the strap.
NOTE: When assembling the CABINET
COVER, connect the Door S/W connector.
COVER, connect the Door S/W connector.
SWITCH ASSY, DOOR LOCK
51
• V ~ U (8~11Ω)
• U ~ W (8~11Ω)
• W ~ V (8~11Ω)
• U ~ W (8~11Ω)
• W ~ V (8~11Ω)
Motor Stator
U V W
Hall Sensor
Ha
Hb
Common
• Common ~ Ha (5~15kΩ)
• Common ~ Hb (5~15kΩ)
• Common ~ Hb (5~15kΩ)
1 Remove the housing coupled the TSG
(Connector, Hoses, Earth Screw)
2 Taking ou the screw of the TSG.
1 Remove the back cover.
2 After loosening the bolt, Rotor, pull out the
rotor.
1 Remove the 6 bolt from the stator.
2 Disconnect the 2 connectors.
2 Disconnect the 2 connectors.
1 Remove the hinges (Damper) at the Tub.
3 The hinge at the base is pulled off.
(To arrow direction)
2 The Hinge(Damper) at the base is pulled off
pressing on the snaps at the sharp end.
TSG (TURBO STEAM GENERATOR)
ROTOR ASSEMBLY, STATOR ASSEMBLY, FRICTION DAMPER
< Heater for STEAM>
• Rating : 230V 1000W
• Resistant : 42.5~49.5Ω
• Rating : 230V 1000W
• Resistant : 42.5~49.5Ω
Click on the first or last page to see other F1480TDS / F1480TDS5 / F1480TDS6 service manuals if exist.