DOWNLOAD LG F1443KDS / F1443KDS7 / F1443KDS9 Service Manual ↓ Size: 14.07 MB | Pages: 64 in PDF or view online for FREE

Model
F1443KDS F1443KDS7 F1443KDS9
Pages
64
Size
14.07 MB
Type
PDF
Document
Service Manual
Brand
Device
Washing Machine
File
f1443kds-f1443kds7-f1443kds9.pdf
Date

LG F1443KDS / F1443KDS7 / F1443KDS9 Service Manual ▷ View online

9
Used the horizontal tap
Horizontal tap
Extension tap
Square tap
1. Unscrew the adapter ring plate and the 4 adapter retaining
screws.
2. Remove the guide plate if the tap is too large to fit the
adapter.
3. Push the adapter onto the end of the tap so that the rubber
seal forms a watertight connection. 
Tighten the adapter ring plate and the 4 screws.
4. Pull the connector latch plate down, push the inlet hose onto
the adapter, and release the connector latch plate. 
Make sure the adapter locks into place.
After completing connection, if water leaks from the hose, repeat the same steps. 
Use the most conventional type of faucet for water supply. In case the faucet is square or too big, remove the
spacing ring before inserting the faucet into the adaptor.
Ring plate
Guide plate
Latch plate
Type-C : Connecting one touch type hose to tap without thread
Step3: Connect hose to washer
• Make sure that there are no kinks in the hose and that they are not
crushed.
When your washer has two valves.
• The Inlet hose which has red connector is for the hot water tap.
• If the washer has two valves, the energy is saved by using hot valve.
After connecting inlet hose to water tap, turn on the
water taps to flush out foreign substances (dirt, sand or
sawdust) in the water lines. Let water drain into a
bucket, and check the water temperature.
10
Connect Drain Hose.
6
Connect power plug.
7
If the drain hose is not installed properly, the unit will not drain properly.
This allows water to back flow into the unit which can cause odors.
Refer to Owner Manual for proper drain hose installation.
The odor could also be coming from the home’s drain to which the drain hose is attached.
In this type of drain hose installation, the odor could be coming from the standpipe.
This odor can come up the drain hose and into the unit.
Pour a cup or two of bleach or vinegar down the home drain 
and let it sit for 24 hours before running another cycle.
This will help eliminate odor from the home drain. 
If a cycle is started too soon after doing this, it will not help the issue.
Connect the power plug to the wall outlet.
Avoid connecting several electric devices, 
it may be the cause of a fire.
about 100 cm
about 145 cm
about 105 cm
Laundry tub
Max. 100cm
min. 60cm
Max. 100cm
min. 60cm
Retainer
Tie
strap
Hose
min. 60 cm
max. 100 cm
Check the horizontality with a level (Gage).
8
1 Step
If washing machine legs are loose or not screwed, then 
screw up
with the spanner wrench. 
Using the level, level the washing machine from front to back and side to side.
2 Step
Using the spanner wrench to adjust leg for 
horizontality
and try for 
Diagonal test
.
3 Step
Perform a Rinse and Spin with some clothing in the machine.
To do this, put 2~3kg of clothing in the unit, power on the unit, Select the Rinse+Spin 
and then start. When the unit reaches the spin cycle, watch for vibrations.
If the unit is vibrating, make small adjustments to the leg until they subside. (Try 2Step again)
4 Step
Tighten
the lock nut against the base of the machine to 
lock
the 
position leg
.
Lower the foot until there is no gap between floor and foot.
And only use 
adjustment rubber
when difference at the leg adjustment is more than 
10mm
.
Place your right hand on the back, right corner and your left hand on the front,
left corner of the unit, then attempt to rock the unit from corner to corner.
Then, move your right hand to the front, right side and your left hand to the
back, left corner and attempt to rock the unit from corner to corner.
If the unit is level, it will not rock.  However, if the unit is not level, it will rock.
If the unit rocks, it will be necessary to adjust the leveling feet of the unit.
Adjust the foot under the hand that is on the front of the machine.
How to perform a diagonal test:
A level
Higher
Tighten
Adjustable feet
Diagonal test
Tighten
Adjustable feet
Higher
Tighten
Adjustable feet
Lower
4620ER4002B
(Gray)
for Wooden floors
Rubber Cup
4620ER4002A
(Black)
for Tile floors
11
Floor
No Gap
Floor
Gap
Lock nut
10mm
Adjustable bolt
Tighen the lock nut
Floor
No Gap
12
Test operation
9
1
Preparation
for 
washing.
· Connect the power plug to the
outlet.
· Connect the inlet hose.   
2
Press the power button.
3
Press the START/PAUSE
button.
6
Check the water heating.
· Press Option right and Rinse
button simultaneously and the
present temperature will be
displayed. 
Page 13
· Check if the drum rotates
clockwise and  counterclockwise. 
5
Check automatic reverse turn.
4
Check the water supply.
· Check if water is supplied through
the detergent dispenser.
7
Check the drain and spin
functions.
· Power off and the power on.
· Select the spin rpm.
· Press the START PAUSE button.
· Check the spin and drain
functions.
· Power off and then power on.
· Listen for a dick determine if
the door is unlocking.
8
Power off and open the
door.
9
Water removal.
· If SVC is needed during  check,
remove the remaining water by
pulling out the hose cap.
· In case of Coloreds program.
Page of 64
Display

Click on the first or last page to see other F1443KDS / F1443KDS7 / F1443KDS9 service manuals if exist.