DOWNLOAD LG F1443KD6 Service Manual ↓ Size: 17.53 MB | Pages: 66 in PDF or view online for FREE

1. Unplug power cord.
2. Remove rear panel.
3. Remove Washer Top.
4. Remove Main PCB Assembly cover as shown in Figure below.
5. Locate the white Hall Sensor 4 wire connector using wiring diagram wire colors

as your guide.

6. Plug in power cord, close door, and press power button. DO NOT PRESS

START!

7. Place meter leads on White & Gray wires. You should read 10 to 15 Vdc output

from the Main PCB Assembly to the Hall sensor. If no 10 to 15 Vdc is
measured the control board is defective.

8. Place meters leads on Blue to Gray. Turn motor rotor slowly by hand. You

should measure a pulsing 10 Vdc. Place meter leads on Red to Gray. Turn
motor rotor slowly by hand. You should measure a pulsing 10 Vdc. If both tests
measure a pulsing 10 Vdc, hall sensor and harness OK. If either or both tests
measures 9 to 10 volts, but does not pulse or change, Hall sensor has failed
and must be replaced. IF zero (0) voltage is measured on either test, check red
& blue wires for continuity. Repair or replace harness as needed.

7. To measure output signal voltage from the hall sensor, carefully move test

leads to terminals 1 to 4, blue and gray. Slowly rotate motor rotor by hand. 
You should read a pulsing 10 Vdc. If 10 Vdc is measured from 1 to 4, move
lead on blue wire to red wire, terminal 2. Repeat rotating motor rotor by hand.
You should read a pulsing 10 Vdc from red to gray.

8. If pulsing 10 Vdc is measured from 1 to 4 and 2 to 4, hall sensor is OK! If either

test netted only 9 to 10 Vdc without changing (no pulsing) the hall sensor is
likely defective. Disconnect power by unplugging washer and ohm check hall
sensor to verify failure of the hall sensor.

Test Points

(1) to (2)

(1) to (3)

(1) to (4)

(2) to (4)

(3) to (4)

Result

8-12 kΩ

8-12 kΩ

10-15 Vdc

10 Vdc

10 Vdc

Remarks

Voltage Input

Pulsing Signal

Pulsing Signal

9-4. PUMP MOTOR ASSEMBLY

      

 

 

!

" # 

  

  !

  !

!  
!  

  !

 

  !  

$!

%

&

'(

) *

"*

+

* All load circuits in wiring diagram areall thesame.

Two pump motors are used to drain the tub and to circulate the water / detergent solution.

  "

  "

Test Points

Result

(1) to (2)

10-20 Ω

,

)* 

-.

-.

-.

-.

9-5. INLET VALVE ASSEMBLY

      

   

 

Depending on the cycle and water temperature, the controller will energize the hot or cold

water valve solenoids to meet the selected water temperature.

After pull out the connector of defective valve, check the resistance.

Test points

(1)-(2)

Result

0.8-1.2 kΩ

 !

"#

"#

#

#

$ %

$ %

$ %

$ % !

#

&

'( 

%

)

&

)

%

$

$

%

)

$

%

)

&

)

%

$

&

)

%

$

&

)

%

$

*+,

  

 

* All load circuits in wiring diagramare all the same.

*$, *%,

*$, *%,

*$, *%,

*$, *%,

10. DISASSEMBLY INSTRUCTIONS

Remove the power cord from the outlet before disassembling or repairing the unit.

1 Unscrew the screws on the top plate.

3 The cover(Inner) is disassembled.

2 The plate assembly(Top) is pulled back and

then upward in direction of arrow. 

1 Pull out the drawer and unscrew 2 screws.

2 Lift the side of the Control Panel Assembly and

pull it out 

1 Unscrew two screws.

2 Push out PANEL ASSEMBLY, CONTROL after

Push the hook below.

1 The PWB assembly(Display) is disconnected.

2 When 7 screws are unscrewed on the PWB

insulator and the PWB assembly(Display) is
disassembled from the PWB insulator.

Screws

Screws

Screws

Disassembly 3 connectors.