LG F12695RDH Service Manual ▷ View online
6
3. PARTS IDENTIFICATION
Drawer
Drum
Door
Drain Hose
Adjustable Feet
Transit Bolts
Control Panel
Power Plug
Drain Pump Filter
Drain Plug
Lower Cover Cap
If the supply cord is damaged,
it must be replaced by the
manufacturer or its authorized
service technician in order to
avoid a hazard.
it must be replaced by the
manufacturer or its authorized
service technician in order to
avoid a hazard.
ACCESSORIES
Inlet hose(1EA) Option : Hot / Cold(2EA)
Spanner
7
4. INSTALLATION
INSTALLATION
The appliance should be installed as follows.
Check the conditions of installation area.
1. Check level ground.
On raised foundations or upper level homes, the vibrations can be caused by the type of flooring.
It may be necessary to move the machine to a different area in the home or have the floor
reinforced to properly support the operation of the unit.
It may be necessary to move the machine to a different area in the home or have the floor
reinforced to properly support the operation of the unit.
2. Check for humidity or any foreign objects under the feet.
Clean the floor, there should be no foreign objects under the feet.
If the unit has foreign objects underneath the feet, this will prevent the unit from being leveled properly
and will cause vibrations and slipping.
Remove any foreign objects, if any from underneath the machine and level unit properly.
See below for examples of foreign objects.
If the unit has foreign objects underneath the feet, this will prevent the unit from being leveled properly
and will cause vibrations and slipping.
Remove any foreign objects, if any from underneath the machine and level unit properly.
See below for examples of foreign objects.
1
Open the box and check appliance condition.
2
horizontal
Carpet
Paper
Laminated
paper
Purchased
stopper
Base Packing
Washer
Spanner
1. Remove the cardboard box and styrofoam packing.
2. Lift the washing machine and remove the base packing.
3. Remove the tape securing the power supply cord and
drain hose.
4. Remove the inlet hose from the drum.
Keep the spanner provided for future use.
8
Use spanner to remove transit bolts.
3
Check the distance between the appliance and the wall.
4
The tap connection and hose connection must be parallel.
5
Transit Bolt
More than 2cm
If the distance is less than 2cm,
the water supply hose will be
kinked or folded.
the water supply hose will be
kinked or folded.
Unfasten
1. Unfasten the adapter ring plate and the 4 adapter retaining screws.
2. Push the adapter onto the end of the tap so that the rubber seal forms
a watertight connection. Tighten the adapter ring plate and the 4
screws.
screws.
3. Push the water supply hose vertically upwards so that the rubber
packing in the hose connects fully to the tap and then
tighten it by fastening clockwise.
tighten it by fastening clockwise.
• Water supply pressure must be between 100 kPa and 1000 kPa (1.0 ~ 10.0 kgf / cm
2
)
• Do not strip or crossthread when connecting inlet hose to the valve.
• If the water supply pressure is more than 1000 kPa, a decompression device should be installed.
• Periodically check the condition of the hose and replace the hose if necessary.
• If the water supply pressure is more than 1000 kPa, a decompression device should be installed.
• Periodically check the condition of the hose and replace the hose if necessary.
Type-A : Connecting Screw-type hose to tap with thread
• Fasten the hose connector onto water supply tap.
Connecting water supply hose
Step1 : Check the rubber seal of the inlet hose
Step2 : Connect hose to water tap
• Two rubber seals are supplied with the water inlet hose.
They are used for preventing water leaks. Make sure the connection to
taps are sufficiently tight.
taps are sufficiently tight.
Upper
connector
connector
Rubber
packing
packing
Plate
Water supply
hose
hose
Fixing screw
Hose
connector
Rubber
seal
seal
Type-B : Connecting Screw-type hose to tap without thread
1. Unfasten the 3 bolts with the spanner supplied.
2. Take out the 3 bolts along with the rubber bungs by slightly
2. Take out the 3 bolts along with the rubber bungs by slightly
twisting the bung.
3. Close the holes with the caps supplied.
Keep the transit bolts for future use.
9
Please use the horizontal tap
Horizontal tap
Extension tap
Square tap
1. Unfasten the adapter ring plate and the 4 adapter retaining
screws.
2. Remove the guide plate if the tap is too large to fit the
adapter.
3. Push the adapter onto the end of the tap so that the rubber
seal forms a watertight connection.
Tighten the adapter ring plate and the 4 screws.
Tighten the adapter ring plate and the 4 screws.
4. Pull the connector latch plate down, push the inlet hose onto
the adapter, and release the connector latch plate.
Make sure the adapter locks into place.
Make sure the adapter locks into place.
After completing connection, if water leaks from the hose, repeat the same steps.
Use the most conventional type of faucet for water supply. In case the faucet is square or too big, remove the
guide plate before inserting the faucet into the adaptor.
Use the most conventional type of faucet for water supply. In case the faucet is square or too big, remove the
guide plate before inserting the faucet into the adaptor.
Ring plate
Guide plate
Latch plate
Type-C : Connecting one touch type hose to tap without thread
Step3: Connect hose to washer
• Make sure that the hose is not kinked or crushed.
When your washer has two valves.
• The inlet hose with the red connector is for the hot water tap.
• If the washer has two valves, energy is saved by using the hot valve.
• If the washer has two valves, energy is saved by using the hot valve.
After connecting inlet hose to water tap, turn on the
water tap to flush out foreign substances (dirt, sand or
sawdust) in the water lines. Let water drain into a
bucket, and check the water temperature.
water tap to flush out foreign substances (dirt, sand or
sawdust) in the water lines. Let water drain into a
bucket, and check the water temperature.
Click on the first or last page to see other F12695RDH service manuals if exist.