DOWNLOAD LG F1069FD6S Service Manual ↓ Size: 6.04 MB | Pages: 44 in PDF or view online for FREE

Model
F1069FD6S
Pages
44
Size
6.04 MB
Type
PDF
Document
Service Manual
Brand
Device
Washing Machine
File
f1069fd6s.pdf
Date

LG F1069FD6S Service Manual ▷ View online

6
3-2. WATER LEVEL CONTROL
This model incorporates a pressure sensor which can sense the water level in the tub.
The water supply is stopped when the water level reaches the preset level; then the selected cycle begins.
Spinning does not proceed until the water in the tubdrains to a certain level.
3-3. DOOR CONTROL
The door can be opened by pulling the door handle whenever washer is not in operation.
When the cycle is completed, the DOOR LOCKED light will turn off.
If a power failure has occurred while in operation, the door will unlock after 2 minutes.
Clicking sounds can be heard when the door is locked/unlocked.
3-4. THE DOOR CAN NOT BE OPENED
While program is operating.
While Door Lock lights turn on.
While the drum is rotating.
3-5. DOOR LOCKED LAMP LIGHTS
When the frequency of water level is lower than 22,9 kHz.
(It can be canceled when the frequency is more than 23,8 kHz.)
When the temperature inside the tubis higher than 45 C (104 F) and water level is not 25,5 kHz.
(It can be canceled when the water level is 25,5 kHz or the temperature inside the tub is lower than
40 C (113 F). )
4. PARTS IDENTIFICATION
Drain Hose
Dispenser
Door
Lower Cover Cap
Drain Plug
Drain Pump Filter
Adjustable Feet
Control Panel
Shipping Bolts (4)
Cold Water Inlet
Hot Water Inlet
Air Vent for Safety
Name:
Front-loading Washing Machine
Power supply:
220-240 V~, 50 Hz
Size:
686 mm (W) X 767 mm (D) X 983 mm (H), 129.1 cm (D with door open)   
Weight:
87 kg
Wash capacity:
10kg
Spin speed:
1150 rpm max.
Permissible water pressure: 1,0 - 8,0 kgf/cm
2
(100 - 800 kPa)
Back of Washer
Specifications subject to change by manufacturer.
Note
Accessories
Hot and Cold
Water Hoses
Elbow Bracket
(for securing drain hose)
Tie Strap
(for securing drain hose)
Wrench 
(for removing shipping
bolts and adjusting
leveling feet)
Caps (4)
(for covering shipping bolt holes)
Non-skid pads
Drum
7
Magnet Door
Plunger
(see page 5)
8
5. INSTALLATION INSTRUCTIONS
Unscrew the 4 bolts with the wrench supplied
Take out the 4 bolts by twisting the braces slightly
Keep the 4 bolts and the wrench for future use
(Whenever the appliance is transported, the
shipping bolts and braces must be replaced.)
Close the holes with the caps supplied.
The appliance is fitted with shipping bolts to prevent
internal damage during transportation.
Packing and all shipping bolts must be removed
before using the washer.
When unpacking the base, be sure to remove
the additional packing support in the middle of
the base packing.
Shipping bolts
• Washer is heavy. Two or more people may be needed to install and move the appliance.
Failure to do so can result in back or other injury.
• Store and install the washer where it will not be exposed to temperatures below freezing or exposed to
outdoor weather conditions. Failure to follow this warning can cause serious injury, fire, electric shock, or
death.
• This appliance must be properly grounded for personal safety. Properly ground washer to conform with all
governing codes and ordinances. Failure to follow this warning can cause serious injury, fire, electric shock, or
death.
• Do not install the washer in humid spaces to reduce the risk of electric shock. Failure to follow this
warning can cause serious injury, fire, electric shock or death.
• The base opening must not be obstructed by carpeting when the washer is installed on a carpeted floor. 
• Do not remove ground prong. Do not use an adapter or extension cord. Plug into a grounded 3 prong outlet.
Failure to follow this warning can cause serious injury, fire, electric shock or death.
• Keep the area underneath and around your appliances free of combustible materials such as lint,
paper, rags, chemicals, etc. Failure to do so can result in fire. 
• To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including the
use of long sleeved gloves and safety glasses. Failure to follow all of the safety warnings in this manual could
result in property damage, injury to persons or death.
Removing shipping bolts
Wrench
CAP
!
WARNING
9
Installation clearances
The location must be large enough to open 
the washer door completely. 
Washer dimensions
The following dimensions shown are for the minimum
spacing allowed.
Additional spacing should be considered for
installation and servicing.
• Additional clearances might be required for wall,
door, and floor moldings.
• Additional spacing of 4 (10 cm) on back, 
1 (2,5 cm) on all sides of the washer is
recommended to reduce noise transfer.
Companion appliance spacing should also be
considered.
Minimum installation spacing for
recessed area installation.
Front view
Side view
Page of 44
Display

Click on the first or last page to see other F1069FD6S service manuals if exist.