DOWNLOAD LG F A5QDP1-9 / F10C3QD / F10C3QDP / F10C3QDP2 / F12A5QD / F12A5TDP / F12C3QD / F12C3QDP / F12C3QDP1 Service Manual ↓ Size: 17.07 MB | Pages: 44 in PDF or view online for FREE

7-4. ERROR DISPLAY

If you press the [Start/Pause] button when an error in displayed, any error except software ERROR will
disappear and the machine will change into pause status.
In case of        ,        ,        , if the error is not resolved within 15 sec. In case of other errors, if the
error is not resolved within 4 min. Power will be turned off automatically and the error only will be
blinked. But in the case of       , power will not be turned off.

WATER 

I

NLET

E

RROR

Water has not reached to the pre-set level within 4 min.

since inlet valve operated, or water has not reached to

the normal level within 25 min. 

Page 19

1

U

NBALANCED 

E

RROR

2

WATER 

O

UTLET

E

RROR

3

OVER

F

LOW 

E

RROR

4

The appliance is tilted.
Laundry is gathered to one side.
Non distributable things are put into the drum.

Page 20

Water has not drained enough within 8 min.

Page 21

Water is automatically being pumped out because too

amuch water is in the tub.

Page 23

P

RESSURE SENSOR

S/W 

E

RROR

5

The sensor pressure switch is out of order.

Page 24

D

OOR OPEN 

E

RROR

6

The [Start/Pause] button is pressed with the door open.
The door switch is out of order.

Page 25

T

HERMISTOR(HEATING)

E

RROR

7

The thermistor is out of order. 

Page 26

C

URRENT

E

RROR

8

PWB ASSEMBLY (Main) is out of order

Replace the PWB assembly (Main)

Winding in the MOTOR is short-circuited.

Replace the MOTOR

MOTOR

L

OCKED 

E

RROR

9

The Connector (3-pin, male, white) in the wire harness

is not connected to the Connector (3-pin, female, white)

of MOTOR.

Reconnect or repair the connector

The electric contact between the connectors [3-pin,

male, white in the wire harness and 6-pin, female, white

in the PWB ASSEMBLY (Main]) is bad or unstable.

Reconnect or repair the contact in the connector

The wire harness between the MOTOR and PWB

ASSEMBLY (Main) is cut (open circuited).

The hall sensor is out of order/defective.

Page 27

7-5. TROUBLESHOOTING WITH ERROR

Water Inlet Error (IE)

Is the water tap closed ?

[Note] Environmental safety check list

1. No water tap leakage & freeze.

2. No entanglement of water supply hose.

5. No the inlet filter clogged.

Check the 

Water tap

and  open it fully .

When there is water in the tub,
is the water level frequency
over 25.5KHz ?

Reconnect or repair the 

Connector

.

Or replace the 

Harness

.

Replace the 

Inlet Valve

.

Is the 

Connector

connected correctly to 

the 

Main PCB

and the 

Inlet Valve

?

Or is the 

Harness

alright ?

Check the 

Air Chamber

and 

the Tube

(clogged) 

And When you check the water level frequency again, 
if it is over 25.5KHz, you replace 

the Pressure switch.

YES

YES

NO

NO

Replace the 

Main PCB

.

NO

YES

YES

NO

NO

Is the each resistance of Inlet Valve within
3.5 ~4.5 kΩ ?

When the washing machine is started, 
is operated the inlet valve? 

Pre. Valve

Main Valve

19

1

2

1

2

3. No water shortage.                           4. No water supply hose leakage

Does the load lean toward one

side, or is the load a few items?

Is the washing machine installed

at an angle?

Adjust the height of washing

machine to be kept horizontally. 

( Page 7)

Is the laundry mixed?

The few items of clothing will clump together 

and their weight will be in one place on the drum,

throwing the weight off during spin mode.

Try rearranging the laundry in drum 

Or the laundry is separated by size, type, and color.

Separate by size, 

type and color

Is the drain hose kinked ?

Check drain hose for kink and straighten the 

.

Drain Hose

Is the 

clogged ?

Check & Clean 

.

This kind of accumulation on the drain filter not only
prevents proper drainage, but also will promote
bacteria growth and cause odors.
This drain filter should be cleaned once a month.

Open the Cover by coin or

finger(only new model)

Drain water by removing the

hose cap.

Disassemble the pump

filter by turning the filter

cap counterclockwise.

Filter clogged by foreign objects

Assemble & close cap

Clean the filter