LG EWF7808 Service Manual ▷ View online
8
HOW TO CONNECT INLET HOSE
Check that the rubber washer is inside of the
valve connector.
Connect the inlet hose firmly to prevent leak.
CONNECT DRAIN HOSE
CONNECT POWER PLUG
Make sure that the hose is not twisted.
The drain hose should be placed under 100cm from the floor.
Connect the power plug to the wall outlet.
Avoid connecting several electric devices,
It may be the cause of a fire.
Avoid submerging the end of the hose.
9
TEST OPERATION
Pre
1200
1000
800
600
no Spin
1000
800
600
no Spin
Main
Super
Normal
Rinse hold
P
(Wash)
(Rinse)
(Spin)
Connect the power plug to
the outlet.
the outlet.
Connect the inlet hose.
Troubleshooting refer to (8-4.ERROR DISPLAY)
Assemble and disassemble refer to (10.Disassembly Instructions)
Assemble and disassemble refer to (10.Disassembly Instructions)
Preparation for
washing.
Press the
POWER ( )
button.
POWER ( )
button.
Press the
PROGRAM ( )
button.
Press the
(START/PAUSE)
( ) button.
(START/PAUSE)
( ) button.
·In case of coloreds
program.
·In case of coloreds
program.
·Press the button (WATER TEMP)
( ) and then the
present temperature in
displayed.
displayed.
·Check if the drum rotates to
clockwise and counterclockwise.
·Check shower because the
water supplied on the door
at first.
at first.
·After power off, press the
DOOR OPEN ( ) button to
check the door open.
check the door open.
·If SVC is needed, during
check and remove
the remaining water by pulling
out the hose cap.
Check the water heating.
Check automatic reverse
Check the water supply.
turn.
Check the drain and spin
Power off
Water removal
P
10
5. OPERATION
(Wash)
(Rinse)
(Spin)
(Water Temp)
(Time Delay)
Pre
R
H
S
N
T
T
Main
1200(1000)
1000(800)
800(600)
600(400)
no Spin
1000(800)
800(600)
600(400)
no Spin
50
30
40
Cold
60
95
How to set the Function
Rinse hold
• Rinse hold function can be selected by pressing the rinse
( ) button, and rinse hold lamp turns ON.
• Selection rinse hold washer waits without drain / spinning
after rinse.
• To drain and spin, press rinse ( ) button, rinse hold lamp
turns off and drain / spinning starts.
How to select water temperature
• Press the button to select water temperature.
• The water temperature can be selected
[40°C
→ 50°C→ 60°C→Cold→ 30°C ] during
coloreds, or synthetic programs.
• 95°C is selected only for whites program.
• By pressing the button while operating the
present temperature is displayed.
How to use delayed washing
• Press the button when reservation washing is needed.
• When the button is pressed,
`3:00ais displayed. A maximum
delay of
`19:00ahours can be set.
• Whenever pressing it, one hour increases.
•
~ Time delay ₩the power ( ) button to cancel it.
•
~ Time delay ₩means the time required from the present to the
completion of washing.
Displaying abnormal operation
• Display the remaining time (Hour : Minute)
• The remaining time is reduced by
• The remaining time is reduced by
the washing cycle.
• Error lamp is indicated the abnormal operation.
(
)
• Display the reservation time.
For manual wash,
rinse, and spin
rinse, and spin
• Use these buttons to change
washing method, rinse
method spinning speed.
method spinning speed.
• When lamp is off, no selection
has been made.
• Prewashing is available for
coloreds, whites, and
synthetic program.
synthetic program.
■ WD-1223(5)F(H)(B) / WD-1243(5)F(H)(B)
WD-1041(3)F(H)B / WD-102(4)1(5)F(H)B
,
,
,
,
,
,
11
y)
(Program)
(Start/Pause)
(Power)
(Door open)
C
S
i
W
W
R
D
Door lock
P
How to select a program
• 6 programs can be selected by the kind of the laundry.
• By pressing the program ( ) button, [Coloreds
→
Whites
→Rapid→Delicate→Wool→Synthetic] can be
selected.
How to open the door
• Use the button to add the
laundry.
• Press the button to open
the door.
• Only operates when the
power plug is connected to
220-240V~ outlet.
Door lock display
Child-Lock
• It shows whether the door
can be open or not during the
washing cycle.
washing cycle.
• If the lamp is off, the door
can be opened.
• Once Child-Lock is set, all buttons are inoperable
during operation.
• The Child-Lock system can be set at any time
even including during Power Off, on Pause and
operation. It is automatically cancelled when an
operational error occur and when the cycle ends.
operation. It is automatically cancelled when an
operational error occur and when the cycle ends.
• When power is off, the LED indicates
~
₩only.
During operation, or when the program paused the
LED Will indicate
LED Will indicate
~
₩and the remaining time.
Error display
• The display blinks if there is an error.
• no inlet
: Trouble with water supply.
• imbalance : The laundry is tilted to one side.
• no drain
: The drain filter is clogged or the drain
pump is out of order.
Power button
• By pressing the button, it
repeats turning on and off.
• Press the button to cancel
the time delay.
• It turns off in 8 sec. after the
program is finished.
Start/Pause button
• Use the button to start or
pause wash cycle.
• The power turns off
automatically in 4 minutes
after the pause button is
pressed.
after the pause button is
pressed.
• Press the button to change
the program.
P
Click on the first or last page to see other EWF7808 service manuals if exist.