LG 502278 Service Manual ▷ View online
4
PEDESTAL KIT
PEDESTAL INSTALLATION – DRYER
1
Then loosen
1-1/2 turns
1-1/2 turns
Retract fully
2
Retainer
T- clip
To set the dryer to the same height as the
washer, fully retract the leveling feet of the
dryer by turning them clockwise, then turn
them counterclockwise 1-1/2 turns.
washer, fully retract the leveling feet of the
dryer by turning them clockwise, then turn
them counterclockwise 1-1/2 turns.
NOTE: The appliance and pedestal assembly
must be placed on a solid, sturdy, level floor
for proper operation.
must be placed on a solid, sturdy, level floor
for proper operation.
Insert the T-clip of the 4 retainers into the
dryer base as shown. Press up on the back of
the clip and pull outward to lock into place.
dryer base as shown. Press up on the back of
the clip and pull outward to lock into place.
3
4
Place the dryer on the pedestal. Make sure
the front and back feet are in the correct
positions. The dryer feet will fi t into the
innermost positions as shown.
the front and back feet are in the correct
positions. The dryer feet will fi t into the
innermost positions as shown.
Make sure the holes on the pedestal align
with the holes in the retainers, then install 2
screws at each corner to securely attach the
appliance to the pedestal.
with the holes in the retainers, then install 2
screws at each corner to securely attach the
appliance to the pedestal.
NOTE: If the screws are not installed
properly, noise and vibration may result.
properly, noise and vibration may result.
Move the appliance to the desired location.
For dryer
For washer/combo
5
PEDESTAL KIT
PEDESTAL INSTALLATION – FINAL INSTALLATION
1
Lower
Raise
2
Locknut
Loosen the locknuts on all 4 leveling feet of
the pedestal until you can turn them with the
wrench. Turn clockwise to raise or
counterclockwise to lower until the pedestal is
level and all 4 feet are solidly against the
floor.
the pedestal until you can turn them with the
wrench. Turn clockwise to raise or
counterclockwise to lower until the pedestal is
level and all 4 feet are solidly against the
floor.
When installing the pedestal on a wooden fl
oor, place the fl oor pads included with your
appliance under the legs of the pedestal. This
will help reduce vibration when the appliance
is operating.
oor, place the fl oor pads included with your
appliance under the legs of the pedestal. This
will help reduce vibration when the appliance
is operating.
Using the Floor Pads
Securely tighten all locknuts by hand.
NOTE: Noise and vibration may result if
locknuts are not tightened.
Be sure to connect the appliances to all water,
power, or gas lines and draining or venting
connections before operation.
If there is excessive vibration during the first
operation after installation, slightly adjust the
leveling feet.
locknuts are not tightened.
Be sure to connect the appliances to all water,
power, or gas lines and draining or venting
connections before operation.
If there is excessive vibration during the first
operation after installation, slightly adjust the
leveling feet.
3
To make sure the appliance is well set on the
pedestal.
Please adjust all four adjustable feet and lock
nuts of the appliance accordingly.
pedestal.
Please adjust all four adjustable feet and lock
nuts of the appliance accordingly.
GAP
6
PEDESTAL KIT
DISASSEMBLY INSTRUCTIONS
1
2
Protect the floor with a large piece of
cardboard.
Lay the appliance on the cardboard.
Be sure the cardboard is under the entire
lower back of the appliance.
cardboard.
Lay the appliance on the cardboard.
Be sure the cardboard is under the entire
lower back of the appliance.
Open the drawer, and then remove the four (4)
screws (two on each side) on both side of
drawer.
screws (two on each side) on both side of
drawer.
3
4
Pull up the drawer to disassemble.
Remove four (4) screws on the drawer.
5
6
Remove two (2) screws on the either side of
the drawer.
the drawer.
Remove Eleven(11) screws on the cover
assembly. (Upper Cover 3EA, Bottom 4EA,
Back 4EA)
assembly. (Upper Cover 3EA, Bottom 4EA,
Back 4EA)
7
PEDESTAL KIT
DISASSEMBLY INSTRUCTIONS
7
8
Loosen the leg using the wrench.(supplied)
9
Remove four (4) screws (two on each side) on
both side of slide.
both side of slide.
Remove twelve (12) screws on the bottom of
the pedestal.
the pedestal.