LG 48842800 Service Manual ▷ View online
8
Verify that the rubber washer is inside of the
valve connector.
Connect the inlet hose firmly to prevent leaks.
HOW TO CONNECT THE INLET HOSE
CONNECT THE DRAIN HOSE
· Make sure that the hose is not twisted.
CONNECT POWER PLUG
The end of the drain hose should be placed less than 96”from the floor.
· Avoid submerging the end of the hose.
· Connect the power plug to the wall outlet.
· Avoid connecting several electric devices, as
doing so may cause a fire.
9
TEST OPERATION
1
Preparation for
washing.
washing.
• Connect the power plug to
the outlet.
• Connect the inlet hose.
3
Press the Start/Pause
button.
button.
•
Listen for clicking sounds to
determine if the door has
locked.
determine if the door has
locked.
6
Check the water heating
function.
function.
•
Press the WASH / RINSE button
and the present temperature will
be displayed.
and the present temperature will
be displayed.
•
Make sure that the drum rotates
clockwise and counterclockwise.
clockwise and counterclockwise.
5
Check the automatic
reversing rotation of the
drum.
reversing rotation of the
drum.
4
Check the water supply.
•
Verify that if water is supplied
through the detergent dispenser.
through the detergent dispenser.
7
Check the drain and spin
functions.
functions.
•
Press the POWER button twice
to restart.
to restart.
•
Press the SPIN SPEED button.
•
Press the START / PAUSE
button.
button.
•
Check the drain and spin
functions.
functions.
8
Press the
START / PAUSE button.
START / PAUSE button.
9
Water removal.
•
If SVC is required, remove the
remaining water in the tub, by
pulling out the drain plug.
remaining water in the tub, by
pulling out the drain plug.
2
Press the POWER button.
•
Listen for clicking sounds to
determine if the door is
unlocking.
determine if the door is
unlocking.
7
10
5. OPERATION
OPTION BUTTONS
The option buttons allow you to select additional cycle options and
will light when selected. Certain buttons also allow you to activate
special functions by pressing and holding the button for 3 seconds.
will light when selected. Certain buttons also allow you to activate
special functions by pressing and holding the button for 3 seconds.
• Prewash:
Use this option for loads that need pretreatment.
It adds 16 minutes prewash and drain.
It adds 16 minutes prewash and drain.
• Stain Cycle: Adds time to the wash and rinse cycles for better stain
removal. Automatically provides a rinse.
•` Easy Spin:
Be used when there is a vibration problem, especially on
wood floor installations.
wood floor installations.
• Extra Rinse: This option provides an additional rinse cycle.
• Delay Wash: Allows the start of any cycle to be delayed for 1~19(12, 9) hours.
• Delay Wash: Allows the start of any cycle to be delayed for 1~19(12, 9) hours.
POWER ON/OFF BUTTON
Press to turn the washer ON. Press again to turn the
washer OFF.
washer OFF.
NOTE: Pressing the ON/OFF button during a cycle will
cancel that cycle and any load settings will be lost.
cancel that cycle and any load settings will be lost.
MY CYCLE BUTTON
Press the MY CYCLE button to save and
recall a customized wash cycle for future
use.
recall a customized wash cycle for future
use.
You can save the Cycle, Wash/Rinse
Temperature, Spin Speed, and Soil
Level settings, as well as other cycle
options.
Temperature, Spin Speed, and Soil
Level settings, as well as other cycle
options.
TIME AND STATUS
The display shows the settings, estimated
time remaining, options, and status messages
for your washer.
time remaining, options, and status messages
for your washer.
5-1 CONTROL PANEL FEATURES
11
CYCLE SETTING BUTTONS
Use these buttons to adjust the desired cycle
options for the selected cycle.
options for the selected cycle.
• Select a water temperature based on the type
of load you are washing.
• To change the spin speed, select the Spin
Speed button until the desired setting is
displayed.
displayed.
• To change the soil level, select the Soil Level
button until the desired setting is displayed.
STATUS INDICATOR
• These lights show elapsed time of
the selected cycle.
CYCLE SELECTOR KNOB
Turn this knob to select the desired cycle. Once the
desired cycle has been selected, the standard presets
will be shown in the display. These settings can be
adjusted using the cycle setting buttons anytime
before starting the cycle.
desired cycle has been selected, the standard presets
will be shown in the display. These settings can be
adjusted using the cycle setting buttons anytime
before starting the cycle.
Press this knob to START the selected cycle. If the
washer is running, use this knob to PAUSE the cycle
without losing the current settings.
washer is running, use this knob to PAUSE the cycle
without losing the current settings.
NOTE: If you do not press the cycle selector knob
within 4 minutes of selecting a cycle, the washer
automatically turns off.
within 4 minutes of selecting a cycle, the washer
automatically turns off.
DOOR LOCKED lamp
• Lights whenever the door is locked.
• The door can be unlocked by pressing the
• The door can be unlocked by pressing the
Start / Pausebutton to stop the washer.
Click on the first or last page to see other 48842800 service manuals if exist.