LG 48842800 Service Manual ▷ View online
5
2-3. WATER LEVEL CONTROL
This model incorporates a pressure sensor which can sense the water level in the tub.
The water supply is stopped when the water level reaches the preset level, the washing program
then proceeds.
Spinning does not proceed until the water in the tub drains to a certain level.
2-4. DOOR CONTROL
The door can be opened by pulling the door handle whenever washer is not in operation.
When the cycle is completed, the DOOR LOCKED light will turn off.
If a power failure has occurred while in operation, the door will unlock after 5 minutes.
Clicking sounds can be heard when the door is locked/unlocked.
2-5. THE DOOR CAN NOT BE OPENED
While program is operating
When a power failed and power plug is taken out in operation
While Door Lock lights turn on.
White the motor is in the process of intertial rotating, through the operation is paused.
2-6. DOOR LOCKED LAMP LIGHTS
When the frequency of water level is lower than 22.9 kHz
(It can be canceled when the frequency is more than 23.8 kHz)
When the temperature inside the tub is higher than 45 °C and water level is not 25.5 kHz
(It can be canceled when the water level is 25.5 kHz or the temperature inside the tub is lower than 40 °C)
2-7. CHILD LOCK
Use this option to prevent unwanted use of the washer. Press and hold OPTION button for 3 seconds
to lock/unlock control.
When child lock is set, “ ” blinks and all buttons are disabled except the Power button.
You can lock the controls of the washer while washing.
6
3. PARTS IDENTIFICATION
Lower Cover Cap
Drain Pump Filter
Drain Plug
Drain Plug
Shipping Blots
Power Plug
Power Plug
Air Vent Safety
Hot Water Inlet
Cold Water Inlet
• If the supply cord is
damaged, it must be
replaced by the
manufacturer or its
authorized service
technician in order to
avoid a hazard.
replaced by the
manufacturer or its
authorized service
technician in order to
avoid a hazard.
Hot/Cold(1 each)
Hose
Wrench
Tie strap
to secure drain hose to standpipe
inlet hose, or laundry tub
Drain Hose
Dispenser
Control panel
Door
Drum
Ajustable Feet
ACCESSORIES
7
4. INSTALLATION
Before servicing, ask the customer what the trouble is.
Check the setup (power supply is 120V AC, remove the transit bolts, level the washer....).
Check with the troubleshooting guide.
Plan your service method by referring to the disassembly instructions.
Service the unit.
After servicing, operate the appliance to see whether it functions correctly.
Check the setup (power supply is 120V AC, remove the transit bolts, level the washer....).
Check with the troubleshooting guide.
Plan your service method by referring to the disassembly instructions.
Service the unit.
After servicing, operate the appliance to see whether it functions correctly.
STANDARD INSTALLATION
The appliance should be installed as follows:
1
2
3
4
5
6
6
REMOVE THE TRANSIT
BOLTS
• Remove the transit bolts
(4 EA: ) with the supplied wrench.
•
Turn the leveling feet to adjust
the appliance horizontally.
the appliance horizontally.
•
The appliance goes up by
rotating the feet clockwise.
rotating the feet clockwise.
•
The appliance come down by
rotating the feet counterclockwise.
rotating the feet counterclockwise.
• Keep the transit bolts and
spanner for future use.
• Insert the 4 caps
(provided) into the hole.
ADJUST THE
LEVELING
INSTALL THE APPLIANCE
ON A FLAT AND FIRM SURFACE
1
8
Verify that the rubber washer is inside of the
valve connector.
Connect the inlet hose firmly to prevent leaks.
HOW TO CONNECT THE INLET HOSE
CONNECT THE DRAIN HOSE
· Make sure that the hose is not twisted.
CONNECT POWER PLUG
The end of the drain hose should be placed less than 96”from the floor.
· Avoid submerging the end of the hose.
· Connect the power plug to the wall outlet.
· Avoid connecting several electric devices, as
doing so may cause a fire.
Click on the first or last page to see other 48842800 service manuals if exist.