LG 60PS80BD-SA (CHASSIS:PB92A) Service Manual ▷ View online
- 5 -
V
Module Specification
V
Model General Specification
No.
Item
Spec.
Remark
1
Number of Pixels
1920 (H)
× 1080 (V) (1pixel=3 RGB cells)
2
Pixel Pitch
690
㎛ (H) × 690㎛ (V)
3
Cell Pitch
230
㎛ (H) × 690㎛ (V) (Base on G cell)
4
Display Area
1324.8(H)
× 745.2(V) ± 0.5mm
5
Outline Dimension
1380(H)
× 816.6(V) × 62(D) ±1 (mm)
6
Pixel Type
RGB Closed type
7
Number of Gradations
(R)256
× (G)256 × (B)256
(R)1024
× (G)1024 × (B)1024
8
Weight
30.2
±1 Kg (Net 1EA)
314
±3 Kg (8EA/1BOX)
9
Aspect Ratio
16:9
10
Peak Brightness
Typical 1000cd/
㎡ (1/100 White Window pattern at center)
11
Contrast Ratio
Average 150:1 (In a bright room with 100Lux at center)
Typical 30,000:1 (In a dark room 1/100 White Window pattern at center)
12
Power Consumption
Max. 700W (Full-White)
13
Expected Life-time
more than 60,000 Hours of continuous operation
Life-time is defined as the
time when the brightness
level becomes half of its
initial value.
No
Item
Specification
Remark
1.
Receiving System
1) SBTVD / NTSC / PAL-M / PAL-N
2.
Available Channel
1) VHF : 02~13
2) UHF : 14~69
3) DTV : 14-69
4) CATV : 02~135
3.
Input Voltage
1) AC 100 ~ 240V 50/60Hz
Mark : 220V, 60Hz
4.
Market
BRAZIL
5.
Screen Size
60 inch Wide(1920
× 1080)
60PS80BD-SA
50 inch Wide(1920
× 1080)
50PS80BD-SA
50 inch Wide(1366 X 768)
50PQ60D-SA
42 inch Wide(1024 X 768)
42PQ60D-SA
6.
Aspect Ratio
16:9
7.
Tuning System
FS
8.
Module
60H3
60PS80BD-SA
50H3
50PS80BD-SA
50G2
50PQ60D-SA
42G2
42PQ60D-SA
9.
Operating Environment
1) Temp : 0 ~ 40 deg
2) Humidity : ~ 80 %
10.
Storage Environment
1) Temp : -20 ~ 60 deg
2) Humidity : ~ 85 %
- 6 -
INSTRUÇÕES DE REGULAÇÃO
1. Application Range
This specification sheet is applied all of the PB91A/PB92A
PDP TV models.
PDP TV models.
2. Notice
(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order. But it is
flexible when its factory local problem occurs.
(3) The adjustment must be performed in the circumstance of
25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation.
there is no specific designation.
(4) The input voltage of the receiver must keep 100~220V,
50/60Hz.
(5) Before adjustment, execute Heat-Run for 5 minutes.
O
After Receive 100% Full white pattern (06CH) then process
Heat-run (or “8. Test pattern” condition of Ez-Adjust status)
O
How to make set white pattern
1) Press Power ON button of Service Remocon
2) Press ADJ button of Service remocon. Select “10. Test
2) Press ADJ button of Service remocon. Select “10. Test
pattern” and, after select “White” using navigation
button, and then you can see 100% Full White pattern.
button, and then you can see 100% Full White pattern.
[ In this status you can maintain Heat-Run useless any
pattern generator
[ Notice: if you maintain one picture over 20 minutes
(Especially sharp distinction black with white pattern -
13Ch, or Cross hatch pattern - 09Ch) then it can appear
image stick near black level.
13Ch, or Cross hatch pattern - 09Ch) then it can appear
image stick near black level.
3. CPLD DOWNLOAD : JTAG MODE
3-1. << PRINT PORT >> PIN MAP
3-2. << 10P WAFER >> PIN MAP
CPLD Download 6PIN WAFER PIN MAP
(NO DIFFERENCE BETWEEN 08’ AND ‘09 D/L JIG)
1. TCK
2. TDO
3. VCC
4. TMS
5. TDI
6. GND
(NO DIFFERENCE BETWEEN 08’ AND ‘09 D/L JIG)
1. TCK
2. TDO
3. VCC
4. TMS
5. TDI
6. GND
- 7 -
- 8 -
Click on the first or last page to see other 60PS80BD-SA (CHASSIS:PB92A) service manuals if exist.