DOWNLOAD LG 60PS7000-ZA (CHASSIS:PD91A) Service Manual ↓ Size: 20.99 MB | Pages: 77 in PDF or view online for FREE

- 5 -

V

(1) 50” FHD

(2) 60” FHD

Display Screen Device

Aspect Ratio

PDP Module

Operating Environment

Storage Environment

Input Voltage

1

2

3

4

5

6

No

Item

Specification

Remark

50 inch Wide Color Display Module

16:9

PDP50H3####,

RGB Closed(Well) Type, Glass Filter(38%)

Pixel Format: 1920 horiz. By 1080 ver.

1) Temp.

: 0 ~ 40deg

2) Humidity : 20 ~ 80%

3) Temp. : -20 ~ 60deg

4) Humidity : 10 ~ 90%

AC100-240V~, 50/60Hz

PDP

LGE SPEC.

Maker LG

Display Screen Device

Aspect Ratio

PDP Module

Operating Environment

Storage Environment

Input Voltage

1

2

3

4

5

6

No

Item

Specification

Remark

60 inch Wide Color Display Module

16:9

PDP60H3####,

RGB Closed(Well) Type, Glass Filter(38%)

Pixel Format: 1920 horiz. By 1080 ver.

1) Temp.

: 0 ~ 40deg

2) Humidity : 20 ~ 80%

3) Temp. : -20 ~ 60deg

4) Humidity : 10 ~ 90%

AC100-240V~, 50/60Hz

PDP

LGE SPEC.

Maker LG

- 6 -

V

 

 

 

 

 

 

 

 

 

 

- 7 -

This spec. sheet is applied to all of the PD91A chassis.

1. The module keeping condition: The normal temperature

condition(more than 15°C)
--> Immediately the line supply.

2. The module keeping condition: 0°C

-->  The module must be kept for more than 2 hours at the

normal temperature.

3. The module keeping condition: -20°C

-->  The module must be kept for more than 3 hours at the

normal temperature.

4. The case of Gu-mi factory at the winter season.

-->  The module must be kept for more than 5 minutes at

the heating zone(40°C~45°C).

(1) The adjustment is according to the order which is

designated and which must be followed, according to the
plan which can be changed only on agreeing.

(2) If there is no specific designation, the adjustment must be

performed in the circumstance of 25±5°C of temperature
and 65±10% of relative humidity.

(3) The input voltage of the set must keep 100~240V,

50/60Hz.

(4) Input signal Unit: Product Specification Standard.
(5) The set must be operated for about 5 minutes prior to the

adjustment.

O

After turning on RGB Full Window pattern in HEAT-RUN

Mode, the receiver must be operated.

O

Enter into HEAT-RUN MODE 

1) Press the ‘POWER ON’ button on R/C for adjustment.
2) Press the ‘ADJ’ button on R/C and enter EZ ADJUST

Select “7. Test Pattern” by using 

D

/

E

(CH +/-) and press

ENTER(

V

)

Select “White” by using 

F

/

G

(VOL +/-) and press

ENTER(

V

)

- Set heat run should be activated without a signal generator. 
- Single color patterns (RED / BLUE / GREEN) of HEAT RUN

MODE are used to check a plasma panel. 

- Caution: If you turn on a still screen more than 20 minutes

(Especially digital pattern, cross hatch pattern), an after
image may be made in the black level part of the screen.

[Caution] 
- Use ‘power on’ button of a service R/C to power on TV set.
- Do not connect any external input cable if there is no any

specifics.

Caution: S/W version of USB file (xxx.epk) must be bigger than

one which is downloaded previously.

(1) Insert the USB stick to the USB socket 
(2) A downloaded file in USB stick will be detected

automatically.

(3) If S/W version of USB file (xxx.epk) is bigger than one

which is downloaded previously, the message, “Copying
files from memory”, will appear. 

(4) If an update procedure was completed, TV set will be

turned off and on automatically.

(5) If TV set is turned on, check an updated version.

* If a downloaded version is more bigger than one of which

TV set had, TV set can lost channel data. In this case,
you have to scan channels again. 

(1) Push “IN-START” button on a service R/C.
(2) Select “Tool Option 1” and Push “OK” button.
(3) Put the number of a below table in order of a suffix of the

“Tool Option(X)”. 
(Each model has a different number.)

(1) Input the component (480i/Horizontal Color Bar) signal to a

TV set.
1) Input Signal Timing : Component 480i 

(Other external connection is unnecessary except the
component before executing ADC calibration.)

2) Input Signal Pattern

@ MODEL: 209 in Pattern Generator(480i Mode)
@ PATTERN : 65 in Pattern Generator(MSPG-925

SERISE) 

(2) Push “ADJ” button on a service R/C.
(3) Enter internal ADC mode by selecting ‘5. ADC Calibration’.
(4) If you select ‘Start’ on a dialog box of the screen, ADC

calibration will be begun.

Caution: Don’t connect any external input cable except the

component input(480i/Horizontal_Color_Bar) to adjust
ADC calibration

O

Auto ADC Calibration Map(RS-232C)

# Adjust Sequence

- aa 00 00  [Enter Adjust Mode]
- xb 00 40  [Component1 Input (480i)]
- ad 00 10  [Adjust 480i Comp1]
- xb 00 60  [RGB Input (1024*768)]
- ad 00 10  [Adjust 1024*768 RGB]
- aa 00 90  End Adjust mode

(1) Push “ADJ” button on a service R/C.
(2) Enter EDID auto download mode by selecting ‘8. EDID

D/L’.

(3) If you select ‘Start’ on a dialog box of the screen, EDID

download will be begun automatically.

(4) Press ‘EXIT’ button on a service R/C.

(5) EDID Data

1) HDMI (256 bytes)

2) RGB (128 bytes)

O

EDID Data detailing (

ⓐ

, 

ⓑ

, 

ⓒ

, 

ⓓ

, 

ⓔ

, 

ⓕ

)

- 8 -

<Horizontal Color Bar pattern>

NO

Item

CMD1

A

A

0

0

0

1

D

A

CMD2 Data0

Enter  

Adjust MODE

Adjust 

‘Mode In’

When transfer the ‘Made

In’, Carry the command.

Automatically adjustment

(The use of a internal

pattern)

ADC

Adjust

ADC Adjust