LG 60PS40FD-AA (CHASSIS:PA91A) Service Manual ▷ View online
- 9 -
8. Adjustment of White Balance
8-1. Required Equipment
(1) Remote controller for adjustment
(2) Color Analyzer (CS-1000, CA-100,100+,CA-210 or same
(2) Color Analyzer (CS-1000, CA-100,100+,CA-210 or same
product) : CH 10 (PDP)
[
Please adjust CA-210, CA-100+ by CS-1000 before
measuring
(3) Auto W/B adjustment instrument(only for Auto adjustment)
(4) 9 Pin D-Sub Jack(RS232C) is connected to the AUTO W/B
(4) 9 Pin D-Sub Jack(RS232C) is connected to the AUTO W/B
EQUIPMENT.
8-2. AUTO White Balance Process
Before Adjust of White Balance, Please press POWER ONLY
key
Adjust Process will start by execute RS232C Command
key
Adjust Process will start by execute RS232C Command
O
Color temperature standards according to CSM and Module
O
CS-1000/CA-100+/CA-210(CH 10) White balance
adjustment coordinates and color temperature.
8-3. Manual W/B Process
(using adjusts Remote control)
Please Adjust in AV 1 MODE, Turn off Energy Saving Mode.
(1) Enter “PICTURE RESET” on Picture Mode, then turn off
Fresh Contrast and Fresh colour in Advanced Control
(2) After enter Service Mode by pushing “ADJ” key,
(3) Enter White Pattern off of service mode, and change off ->
(3) Enter White Pattern off of service mode, and change off ->
on.
(4) Enter “W/B ADJUST” by pushing “
G
” key at “3. W/B
ADJUST”.
(5) Adjust W/B DATA, for all CSM, choose ‘COPY ALL’
[
Gain Max Value is 192. So, Never make any Gain Value
over 192 and please fix one Value on 192, between R, G
and B.
and B.
8-4. Auto-control Interface and Directions
(1) Adjust in the place where the influx of light like floodlight
around is blocked.
(Illumination is less than 10ux).
(2) Measure and adjust after sticking the Color Analyzer (CA-
100+, CA210 ) to the side of the module.
(3) Aging time
After aging start, keep the Power on (no suspension of
power supply) and heat-run over 5 minutes
power supply) and heat-run over 5 minutes
8-5. Auto Adjustment Map(RS232C)
9. Checking the EYE-Q Operation
(1) Press the EYE Key on the adjustment remote controller.
(2) Check the Sensor DATA (It must be under 10) and keep
(2) Check the Sensor DATA (It must be under 10) and keep
the data longer than 1.5s
(3) Check ‘OK’
(Sensor DATA 0 ~ 4095, Power Saving Mode 0 ~ 12)
[
IF you press IN-STAP Button, change Green Eye-check OSD.
PLASMA
Remark
11000K
9300K
6500K
Cool
Medium
Warm
CSM
Color Coordinate
x
y
0.283
0.293
0.329
11,000K
9,300K
6,500K
0.002
0.002
0.002
0.276
0.285
0.313
Cool
Medium
Warm
CSM
Temp
±Color
Coordinate
- 10 -
BLOCK DIAGRAM
501
900
400
300
305
301
304
200
201
580
590
603
602
520
570
560
306
302
206
207
205
204
208
202
203
303
120
240
250
601
A2
LV1
- 11 -
EXPLODED VIEW
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These
parts are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
parts are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
IMPORTANT SAFETY NOTICE
Click on the first or last page to see other 60PS40FD-AA (CHASSIS:PA91A) service manuals if exist.