LG 60PM970S-ZA (CHASSIS:PD22A) Service Manual ▷ View online
- 9 -
4.5. Checking the EYE-Q Operation.
(1) Press the EYE Key on the adjustment remote controller.
(2) Check the Sensor DATA ( It must be under 10) and keep
the data longer than 1.5s
(3) Check ‘OK’
(Sensor DATA 0 ~ 4095, Power Saving Mode 0 ~ 12)
* IF you press IN-STAP Button, change Green Eye-check
OSD.
4.6. PING TEST
* In this case Network setting is on Manual Setting.
Connect : SET->LAN Port == PC->LAN Port
4.6.1. Equipment Setting
(1) Play the LAN Port Test PROGRAM.
(2) Input IP set up for an inspection to Test
* IP Number : 12.12.2.2
4.6.2. LAN PORT inspection (PING TEST)
* In this case Network setting is on Manual Setting.
(1) Play the LAN Port Test Program.
(2) connect each other LAN Port Jack.
(3) Play Test (F9) button and confirm OK Message.
(4) remove LAN CABLE
4.7. Magic Motion Remote Controller test
(1) Equipment: RF R/C for test,
(2) You must confirm the battery power of RF-R/C before test
(Recommend that change the battery per every lot)
(3) Sequence (test)
1) if you select the ‘start key(Wheel Key)’ on the controller,
you can pairing with the TV SET.
2) You can check the cursor on the TV Screen, when select
the ‘Wheel Key’ on the controller
3) You must remove the pairing with the TV Set by select
‘Mute Key’ on the controller.
4.8. Wi-Fi Test(Except for PM47*/PM67*)
Step 1) Turn on TV
Step 2) Select ‘Network Connection’ option in Network Menu.
Step 3) Select ‘Start Connection’ Button in ‘Network
Connection’.
Step 4) If the system finds any AP like blow PIC, it is working
well.4.9. 3D function test
Green Eye-Check(Factory Mode)
Sensor Data
9
Power saving mode
1
OK
- 10 -
4.8. 3D function test
- Required Equipment
● Pattern Generator :
MSHG-600, MSPG-6100 [SUPPORT HDMI1.4])
MODE : HDMI mode NO. 872
Pattern No.83
(1) Please input 3D test pattern like below (HDMI mode NO.
872 , pattern No.83)
(2) When 3D OSD appear automatically, then press OK button
on ADJ Remote Controller.
(3) Check the picture. The picture must be same as below.
(Don’t have to wear 3D glasses.)
4.10. LNB voltage and 22KHz tone check
(only for *PM**0S)
(1) Test method
1) Press "Power on" button of a service R/C.(Baud rate :
115200 bps)
2) Connect cable between satellite ANT and test JIG.
3) Connect RS232-C Signal Cable.
4) Write LNB ON control command through RS-232-C.
5) check LED light ‘ON’ at 18V menu.
6) check LED light ‘ON’ at 22KHz tone menu.
7) Write LNB OFF control command through RS-232-C.
8) check LED light ‘OFF’ at 18V menu.
9) check LED light ‘OFF’ at 22KHz tone menu.
(2) RS-232 command for test LNB
(3) Test result
- After send LNB On command, ‘18V LED’ and ‘22KHz
tone LED’ should be ON.
- After send LNB OFF command, ‘18V LED’ and ‘22KHz
tone LED’ should be OFF.
<Remark> After the measurement conditions witnessed in
the last state.
5. Set Information
(Serial No & Model name)
5.1. check the serial number & Model Name
(1) Push the menu button and press red button on R/C to
enter ‘Customer Support’menu.
(2) Move to ‘signal test’ menu. And check Serial No & Model
Name Select the STATION -> Diagnostics -> To set
6. SW Download Guide.
* Before put a *.epk to USB Stick make ‘LG_DTV’ folder in
USB. Then, put *.epk file to ‘LG_DTV’ folder and Turn on TV
(1) Put the USB Stick to the USB socket
(2) Automatically detecting update file in USB Stick
* If your downloaded program version in USB Stick is Low,
it didn’t work.
But your downloaded version is High, USB data is
automatically detecting.
(3) Show the message “Copying files from memory”
(4) Updating is staring.
(5) Updating Completed, The TV will restart automatically.
After turn on TV, Please press ‘IN-STOP’ button on ADJ
Remote-control.
* IF you don’t have ADJ R/C, enter ‘Factory Reset’ in
OPTION MENU.
(6) When TV turns on, check the Updated version on Product/
Service Info. MENU.
* After downloading, have to adjust TOOL OPTION again.
Command
Set ACK
LNB On
[A][I][ ][Set ID][ ][30][Cr]
[O][K][x] or NG : [N][G][x]
LNB Off
[A][I][ ][Set ID][ ][40][Cr]
[O][K][x] or NG : [N][G][x]
G
tGi
{
k}iTzYGG
ck}iGGGqpnGGe
4;Y
46Y
55NK}#
Wrqh RQ
Wrqh RQ
55NK}
Wrqh#Rii
Wrqh#Rii
tGi
{
k}iTzYGG
ck}iGGGqpnGGe
4;Y
46Y
55NK}#
Wrqh RQ
Wrqh RQ
55NK}
Wrqh#Rii
Wrqh#Rii
4;Y
46Y
55NK}#
Wrqh RQ
Wrqh RQ
55NK}
Wrqh#Rii
Wrqh#Rii
G
tGi
{
k}iTzYGG
ck}iGGGqpnGGe
4;Y
46Y
55NK}#
Wrqh RQ
Wrqh RQ
55NK}
Wrqh#Rii
Wrqh#Rii
tGi
{
k}iTzYGG
ck}iGGGqpnGGe
4;Y
46Y
55NK}#
Wrqh RQ
Wrqh RQ
55NK}
Wrqh#Rii
Wrqh#Rii
4;Y
46Y
55NK}#
Wrqh RQ
Wrqh RQ
55NK}
Wrqh#Rii
Wrqh#Rii
- 11 -
BLOCK DIAGRAM
- 12 -
200
400
300
120
520
590
580
601
201
204
205
206
203
304
209
303
540
310
305
301
208
302
900
910
202
207
501
240
560
LV
1
A10
A9
A12
A2
530
A22
A13
EXPLODED VIEW
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These
parts are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
parts are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
IMPORTANT SAFETY NOTICE
Click on the first or last page to see other 60PM970S-ZA (CHASSIS:PD22A) service manuals if exist.