LG 60PM9700-UA (CHASSIS:PU22A) Service Manual ▷ View online
- 7 -
4.3.2. EDID DATA(AC-3)_PU22A
■ HDMI [C/S: 98 BD] : For FHD Models
EDID Block 0, Bytes 0-127 [00H-7FH]
Block Type: EDID 1.3
EDID Block 1, Bytes 128-255 [80H-FFH]
Block Type: CEA EDID Timing Extension Version 3
■ RGB [C/S: B1] : For FHD Models
EDID Block 0, Bytes 0-127 [00H-7FH]
Block Type: EDID 1.3
5. Final Assembly adj.
* Caution : Each PCB assembly must be checked by check
JIG set. (Because power PCB Assembly damages
to PDP Module, especially be careful)
5.1. POWER Supply Unit PCB Ass'y Va/Vs
Voltage adjustment.
* Caution : Both Vs and Va voltage adjustment are necessary.
5.1.1. Model name
: PU22A
5.1.2. Va/Vs Adjustment Procedure
(1) Connect positive(+) terminal of DMM to Vs/Va pin, connect
negative(-) terminal to GND.
(2) Turning ‘Vs/Va Adjust’ and adjust Vs/Va voltages to a value
which is written on a right/top label of a module.
(deviation ; ±0.5V)
* Caution : Each Power Supply Unit PCB assembly must be
checked by check JIG set. (Because power PCB
Ass’y damages to PDP Module, especially be
careful)
* Caution : Set up "RF mode(noise)" before a voltage adjust-
ment.
5.2. White Balance adj.
5.2.1. Overview
■ W/B adj. : Objective & How-it-works
- Objective: To reduce each Panel’s W/B deviation
- How-it-works: When R/G/B gain in the OSD is at 192,
it means the panel is at its Full Dynamic
Range. In order to prevent saturation of
Full Dynamic range and data, one of R/G/B
is fixed at 192, and the other two is lowered
to find the desired value.
5.2.2. Equipment
(1) Color Analyzer : CA-210 (NCG: CH 9 / WCG: CH12 /PDP
Module:CH10)
(2) Adj. Computer (During auto adj., RS-232C protocol is
needed)
(3) Adj. R/C
(4) Video Signal Generator MSPG-925F
720p/216Gray(Model:217, Pattern:78)
→ Only when internal pattern is not available
■ Color Analyzer Matrix should be calibrated using CS-1000
Vender ID
C/S1
C/S2
HDMI1
10
98
BD
HDMI2
20
98
AD
HDMI3
30
98
9D
HDMI4
40
98
8D
- 8 -
5.2.3. Equipment connection map
5.2.4. Adj. Command (Protocol)
■ Protocol
<Command Format>
- LEN: Number of Data Byte to be send
- CMD: Command
- VAL: FOS Data
- CS: Checksum of sent Data
- A: Acknowledge
Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX]
■ RS-232C Command used during auto-adj.
Ex) wb 00 00 -> Begin white balance auto-adj.
wb 00 10 -> Gain adj.
ja 00 ff -> Adj. data
jb 00 c0
...
...
wb 00 1f -> Gain adj. complete
*(wb 00 20(Start), wb 00 2f(End)) -> Off-set adj.
wb 00 ff -> End white balance auto-adj.
5.2.5. Adj. method
5.2.5.1. Auto adj. method
(1) Set TV in adj. mode using POWER On Key
(2) Zero calibrate probe then place it on the center of the
Display
(3) Connect Cable(RS-232C)
(4) Select mode in adj. Program and begin adj.
(5) When adj. is complete (OK Sign), check adj. status per
mode
(Warm, Medium, Cool)
(6) Remove probe and RS-232C cable to complete adj.
■ Adj. must begin w/ command “wb 00 00”, and end w/“wb
00 ff”and adj. offset if needed.
■ Offset adjust limit value.
Offset Min = 34 (Decimal)
Offset Max = 94 (Decimal)
5.2.5.2. Auto adj. Sequence
- White Balance Adjust Sequence
Start -> Cool_Gain -> Medium_Gain -> Warm_Gain -> End
5.2.5.3. Manual adj. method
Dynamic contrast : off
Dynamic color : off
OPC : Off
Energy saving mode : Off
● Test Equipment: CA-210
- Using PDP color temperature, Color Analyzer (CA-210)
must use CH 10, which Matrix compensated (White, Red,
Green, Blue compensation) with CS-2100. See the
Coordination bellowed one.
● Manual adjustment sequence is like bellowed one.
- Turn to “Ez-Adjust” mode with press ADJ button of service
remocon.
- Select “10.Test Pattern” with CH+/- button and press
enter. Then set will go on Heat-run mode. Over 30
minutes set let on Heat-run mode.
- Let CA-210 to zero calibration and must has gap more
10cm from center of PDP module when adjustment.
- Press “ADJ” button of service remocon and select
“7.White-Balance” in “Ez-Adjust” then press “►” button of
navigation key. (When press “►” button then set will go to
full white mode)
- Adjust at three mode (Cool, Medium, Warm)
- If “cool” mode
Let B-Gain to 192 and R, G, B-Cut to 64 and then control
R, G gain adjustment High Light adjustment.
- If “Medium” and “Warm” mode Let R-Gain to 192 and R,
G, B-Cut to 64 and then control G, B gain adjustment
High Light adjustment.
- All of the three mode
Let R-Gain to 192 and R, G, B-Cut to 64 and then control
G, B gain adjustment High Light adjustment.
- With volume button (+/-) you can adjust.
- After all adjustment finished, with Enter (■ key) turn to
Ez-Adjust mode. Then with ADJ button, exit from
adjustment mode
* Attachment: White Balance adjustment coordination and
color temperature.
RS-232C COMMAND
[CMD ID DATA]
Meaning
wb
00
00
Begin White Balance adj.
wb
00
ff
End White Balance adj. (internal
pattern disappears)
pattern disappears)
9. White Balance
- 9 -
● Using CS-1000 Equipment.
- COOL : T=11000K, ∆uv=0.000, x=0.276 y=0.283
- MEDIUM : T=9300K, ∆uv=0.000, x=0.285 y=0.293
- WARM : T=6500K, ∆uv=0.000, x=0.313 y=0.329
● When tester will measure on Cool condition, adjust W30 on
TV display menu.
● When tester will measure on medium condition, adjust 0 on
TV display menu.
● When tester will measure on warm condition, adjust W30 on
TV display menu.
● Using CA-210 Equipment. (10 CH)
- Contrast value: 216 Gray
- Brightness spec.
5.2.6 Reference
(White Balance adj. coordinate and color temperature)
■ Standard color coordinate and temperature using CS-1000
■ Luminance: Full white 216 Gray
■ Standard color coordinate and temperature using CA-210(CH 10)
- Gain color coordinate
■ Pattern : Full white 216 Gray
5.3. Serial number download & Model name D/L.
(1) Press "Power on" button of a service R/C.(Baud rate :
115200 bps)
(2) Connect RS232-C Signal Cable and start ‘Option Check
Program Ver3.8’
(3) Scan serial Number and press ‘F5’ button.
(4) Check ‘OK’ on program 1) program.
(5) Press ‘In start’ button on SVC R/C, check Serial Number
and Model Name.
5.4. Checking the EYE-Q Operation.
(1) Press the EYE Key on the adjustment remote controller.
(2) Check the Sensor DATA ( It must be under 10) and keep
the data longer than 1.5s
(3) Check ‘OK’
(Sensor DATA 0 ~ 4095, Power Saving Mode 0 ~ 12)
* IF you press IN-STAP Button, change Green Eye-check
OSD.
5.4.1. LAN PORT inspection (PING TEST)
* In this case Network setting is on Manual Setting.
(1) Play the LAN Port Test Program.
(2) connect each other LAN Port Jack.
(3) Play Test (F9) button and confirm OK Message.
(4) remove LAN CABLE
Color
temperature
Test
Equipment
Color Coordination
x
y
COOL
CA-210
0.276 ± 0.002 0.283 ± 0.002
MEDIUM
CA-210
0.285 ± 0.002 0.293 ± 0.002
WARM
CA-210
0.313 ± 0.002 0.329 ± 0.002
Item
White average
brightness
Brightness uniformity
Min
49
-20
Typ
60
Max
+20
Unit
cd/m²
%
Remark - 100% Window White
Pattern
- 100IRE(255Gray)
- Picture: Vivid(Medium)
- 85IRE(216Gray) 100%
Window White Pattern
- Picture: Vivid(Medium)
Color
temperature
Color Coordination
Temp
∆uv
x
y
COOL
0.276
0.283
11000K
0.0000
MEDIUM
0.285
0.293
9300K
0.0000
WARM
0.313
0.329
6500K
0.0000
Color
temperature
Color Coordination
Temp
∆uv
x
y
COOL
0.276 ± 0.002 0.283 ± 0.002 11000K 0.0000
MEDIUM
0.285 ± 0.002 0.293± 0.002
9300K 0.0000
WARM
0.313 ± 0.002 0.329 ± 0.002 6500K 0.0000
Green Eye-Check(Factory Mode)
Sensor Data
9
Power saving mode
1
OK
- 10 -
5.5. Magic Motion Remote Controller test
- Required Equipment : RF Remote Controller for test
* You must confirm the battery power of Remote Controller
before test (Recommend that change the battery per every
lot)
(1) Within 50 cm of the TV set, select the wheel ‘Enter’ button
of the controller.
(2) You can check the controller LED on and the cursor on the
TV Screen.
(3) You must remove the pairing with the TV Set by select
‘Mute Key’ on the controller.
(4) Then you can check the cursor on the TV screen is
disappeared and the controller LED off.
5.6. Wi-Fi Test(Except for PM47*/PM67*)
Step 1) Turn on TV
Step 2) Select ‘Network Connection’ option in Network Menu.
Step 3) Select ‘Start Connection’ Button in ‘Network
Connection’.
Step 4) If the system finds any AP like blow PIC, it is working
well.
5.7. 3D Function Test
( Pattern Generator MSPG-3233, HDMI mode NO. 371 ,
pattern No. 81)
(1) Please input 3D test pattern like below
(2) Enter 3D mode , then select side by side
(If you don’t wear a 3D Glasses, you will see the picture
like below)
<
<
<
<
Click on the first or last page to see other 60PM9700-UA (CHASSIS:PU22A) service manuals if exist.