LG 60PM6700-ZA (CHASSIS:PD22B) Service Manual ▷ View online
- 5 -
5. Model General Specification
No
Item
Specification
Remark
1
Market
Albania, Austria, Belgium, Bosnia, Bulgaria,
Coratia, Czech, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Ireland, Italy,
Kazakhstan, Latvia, Lithuania, Luxembourg,
Morocco, Netherlands, Norway, Poland, Portugal,
Romania, Russia, Serbia, Slovenia, Spain,
Sweden, Slovakia, Switzerland, Turkey, Ukraine, UK
2
Broadcasting system
1) PAL/SECAM BG
2) PAL/SECAM DK
3) PAL I / II
4) SECAM L/L’
5) DVB T / T2
6) DVB C
7) DVB S
EU (PAL Market)
Supporting T2 is only for *PM***T./W
Supporting S is only for **PM***S/G
3
Receiving system
Analog : Upper Heterodyne
Digital : COFDM
► DVB-T
- Guard Interval(Bitrate_Mbit/s)
1/4, 1/8, 1/16, 1/32
- Modulation : Code Rate
QPSK : 1/2, 2/3, 3/4, 5/6, 7/8
16-QAM : 1/2, 2/3, 3/4, 5/6, 7/8
64-QAM : 1/2, 2/3, 3/4, 5/6, 7/8
► DVB-C
- Symbolrate :
4.0Msymbols/s to 7.2Msymbols/s
- Modulation :
16QAM, 64-QAM, 128-QAM and 256-QAM
► DVB-S
- symbolrate
DVB-S2 (8PSK / QPSK) : 2 ~ 45Msymbol/s
DVB-S (QPSK) : 2 ~ 45Msymbol/s
- viterbi
DVB-S mode : 1/2, 2/3, 3/4, 5/6, 7/8
DVB-S2 mode : 1 /2, 2/3, 3/4, 3/5, 4/5, 5/6,
8/9, 9/10
4
Scart Jack (1EA)
PAL, SECAM
Scart 1 Jack is Full scart and support
RF-OUT(Analog), MNT-OUT
5
Video Input (1EA)
PAL, SECAM, NTSC
Rear Hybrid Jack Type
6
Component Input (1EA) Y/Cb/Cr, Y/ Pb/Pr
7
RGB Input (1EA)
RGB-PC
Analog (D-Sub 15Pin)
8
HDMI Input (2 or 3EA)
HDMI-PC
HDMI-DTV
HDMI1, HDMI2(DVI) , HDMI3, HDMI4
9
Audio Input (2EA)
RGB/DVI Audio, Component
L/R Input
10
SPDIF Out (1 EA)
SPDIF Out
11
USB (1EA)
For SVC, S/W Download, X-Studio, DivX
12
Ethernet LAN(1EA)
13
PCMCI (1EA)
Common Interface
- 6 -
ADJUSTMENT INSTRUCTION
1. Application Range
This spec. sheet applies to PD22B chassis applied PDP TV all
models manufactured in TV factory.
2. Specification
(1) Because this is not a hot chassis, it is not necessary to
use an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of
25 °C ± 5 °C of temperature and 65±10% of relative
humidity if there is no specific designation.
(4) The input voltage of the receiver must keep 100~240V,
50/60Hz.
(5) The receiver must be operated for about 5 minutes prior to
the adjustment when module is in the circumstance of over
15 °C
- In case of keeping module is in the circumstance of 0°C, it
should be placed in the circumstance of above 15°C for 2
hours
- In case of keeping module is in the circumstance of below
-20 °C, it should be placed in the circumstance of above 15
°C for 3 hours,.
■ After RGB Full White in HEAT-RUN Mode, the receiver must
be operated prior to the adjustment.
■ Enter into HEAT-RUN MODE
1) Press the POWER ON KEY on R/C for adjustment.
2) OSD display and screen display PATTERN MODE.
● Set is activated HEAT run without signal generator in this
mode.
● Single color pattern ( WHITE ) of HEAT RUN MODE uses to
check panel.
● Caution : If you turn on a still screen more than 20 minutes
(Especially digital pattern, cross hatch pattern), an
after image may be occur in the black level part of
the screen.
3. PCB Assembly adjustment
* Caution : Using ‘power on’ button of the control R/C power on
TV
3.1. MAC Address and ESN and Wide-vine
Key Download
* The CI+ Key download is need for only PD22A/B/C Models.
* Connect TV SET and PC which download keys Writing
program by RS232C-Cable
(1) Start Program and Click ‘start’ Button to connect TV and
PC.
(2) When download succeed, you can see “OK” on the
screen.
* Each Chassis has it’s own MAC Address/ESN/Wide-vine
key. Please be careful of download.
3.2. DFT Process
* Depend on situation, Step can be changed.
* Condition spec
3.3. Tool OPTION (MANUAL)
(1) Press ADJ key on R/C to insert Tool OPTION
(2) On the “ Tool Option ”, Insert Tool Option by a number key
(3) Press the ENTER(■)
(4) Press ENTER(■) again.
(5) Select “OK to Download” by using ◄/►(VOL +/-) and
press ►(VOL +)
Mode
Volume
Power Off
RF
0
DC On
* PD22B
Model Name
PM970
PM690
PM680
PM670
PM470
Tool
option 1
42 HD
33062
50 HD
33064
50 FHD
32808
32904
32920
32936
60 FHD
32810
32906
32922
32938
Tool
option 2
42 HD
66
50 HD
66
50 FHD
65
65
65
65
60 FHD
65
65
65
65
Tool option 3
973
973
973
973
845
Tool option 4
29166
29166
29166
29166
29166
Tool option 5
47703
47703
47703
47701
14933
Tool option 6
1561
1561
1561
1561
1561
Tool option 7
8239
9263
8239
8239
8239
In case of France, Tool Option 5 is 47959/47959/47959/47957/15189.
- 7 -
3.4. EDID
(The Extended Display Identification Data)
■ RGB [C/S: B1] : For FHD Models
EDID Block 0, Bytes 0-127 [00H-7FH]
Block Type: EDID 1.3
■ HDMI [C/S: 9804] : For FHD Models
Block Type: EDID 1.3
EDID Block 1, Bytes 128-255 [80H-FFH]
Block Type: CEA EDID Timing Extension Version 3
* CheckSum & Physical Address Table.
- Each HDMI Input has their own physical address(on
Address:9E). So, each HDMI Input has different C/S
value.
■ HDMI INPUT Physical Address Table
■ HDMI INPUT C/S Table.
- FHD
4. SET assembly adjustment method
* Caution: Each PCB assembly must be checked by check
JIG set. (Because power PCB Assembly damages
to PDP Module, especially be careful)
4.1. POWER PCB Assembly Voltage adjustment
(Va, Vs voltage adjustment)
Test equipment : D.M.M 1EA
Connection Diagram for Measuring : refer to fig.4
Adjustment method
4.1.1. Va adjustment
(1) Connect + terminal of D. M.M. to Va pin of P811, connect
-terminal to GND pin of P811.
(2) After turning VR502,voltage of D.M.M adjustment as same
as Va voltage which on label of panel right/top (deviation;
±0.5V)
4.1.2. Vs adjustment
(1) Connect + terminal of D. M..M. to Vs pin of P811, connect
-terminal to GND pin of P811.
(2) After turning VR901, voltage of D.M.M adjustment as
same as Vs voltage which on label of panel right/top (
deviation ; ±0.5V)
4.2. Adjustment of White Balance
- Required Equipment
● Remote controller for adjustment
● Color Analyzer ( CS-1000, CA-210 or same product
: CH 10 (PDP)
* Please adjust CA-210 by CS-1000 before measuring
● Auto W/B adjustment instrument(only for Auto
adjustment)
● 9 Pin D-Sub Jack(RS232C) is connected to the AUTO
W/B EQUIPMENT
Before Adjust of White Balance, Please press
POWER ONLY key
- Adjust Process will start by execute RS232C Command.
● Color temperature standards according to CSM and Module
● CS-1000/CA-100+/CA-210(CH 10) White balance adjust-
ment coordinates and color temperature.
Address
HDMI1
HDMI2
HDMI3
HDMI4
9E
10
20
30
40
HDMI1
HDMI2
HDMI3
HDMI4
CheckSum
9804
98F4
98E4
98D4
CSM
PLASMA
Cool
11000K
Medium
9300K
Warm
6500K
CSM
Color Coordination
Temp
± Color
Coordination
x
y
COOL
0.276
0.283
11000K
0.002
MEDIUM
0.285
0.293
9300K
0.002
WARM
0.313
0.329
6500K
0.002
- 8 -
* Manual W/B process (using adjusts Remote control)
- Please Adjust in AV 1 MODE, Turn off Energy Saving Mode.
1) Enter ‘PICTURE RESET’ on Picture Mode, and then
turn off Fresh Contrast and Fresh colour in Advanced
Control
2) After enter Service Mode by pushing “ADJ” key,
3) Enter White Pattern off of service mode, and change off
-> on.
4) Enter “W/B ADJUST” by pushing “►” key at “3. W/B
ADJUST”.
* Gain Max Value is 192. So, Never make any Gain Value
over 192 and please fix one Value on 192, between R, G
and B.
* Auto-control interface and directions
(1) Adjust in the place where the influx of light like floodlight
around is blocked. (Illumination is less than 10ux).
(2) Measure and adjust after sticking the Color Analyzer (CA-
100+, CA210) to the side of the module.
(3) Aging time
- After aging start, keep the Power on (no suspension of
power supply) and heat-run over 5 minutes
* Auto adjustment Map (RS232C)
4.3. Serial number download & Model name D/L.
(1) Press "Power on" button of a service R/C.(Baud rate :
115200 bps)
(2) Connect RS232-C Signal Cable and start ‘Option Check
Program Ver3.8’
(3) Scan serial Number and press ‘F5’ button.
(4) Check ‘OK’ on program 1) program.
(5) Press ‘In start’ button on SVC R/C, check Serial Number
and Model Name.
4.4. Check Tool Option and write Country
Group & Area Code(Option) D/L
- Refer to Table 3.3 insert tool option.
No
Index
CMD1
CMD2
Set ID
Data
1
Start
w
b
0
00
2
Gain Start
w
b
0
10
3
Gain End
w
b
0
1F
4
Offset Start
w
b
0
20
5
Offset End
w
b
0
2F
6
End
w
b
0
FF
7
Medium R
j
a
0
00~FF
8
Medium G
j
b
0
00~FF
9
Medium B
j
c
0
00~FF
10
Warm R
j
d
0
00~FF
11
Warm G
j
e
0
00~FF
12
Warm B
j
f
0
00~FF
13
Cool R
j
g
0
00~FF
14
Cool G
j
h
0
00~FF
15
Cool B
j
i
0
00~FF
16
Cool R,G,B
j
j
0
00~FF
17
Medium
j
k
0
00~FF
18
Warm
j
l
0
00~FF
Min
Typ
Max
R-GAIN
0
192
192
G-GAIN
0
192
192
B-GAIN
0
192
192
Country Group
Market
Area Option
AJ
Myanmar
Etc.
257
Australia, New Zealand
Singapore, Malaysia
263
Indonesia
262
Vietnam
261
Thailand
16647
Sri Lanka
17671
India
18183
JA
Irap, Lybia, Yemen,
Syria, Sudan, West Afria
Ect.
257
Tunisia, Kuwait, Oman,
Kenya, Uganda
Palestine(SBITANY)
259
Qatar
Nigeria
260
U.A.E
Saudi Arabia
Barhrain
261
Egypt, Iran, Jordan
Lebanon
263
Pakistan
16642
IL
Israel(H.Y.E)
259
Chassis Name
PD22A
Suffix
EB, PF, EU PD, RU, DR, DK
PI
Area Option
130
386
418
Nordic UI
0~1
0
0
0
Use HW Option
0~1
1
1
1
T2
0~1
0
0
0
C2
0~1
0
0
0
Satellite
0~1
0
0
0
MHP
0~1
0
0
1
HBBTV
0~1
2
2
2
Isolator
0~1
0
1
1
Click on the first or last page to see other 60PM6700-ZA (CHASSIS:PD22B) service manuals if exist.