LG 60PH660V-ZA / 60PH6708-ZD / 60PH670V-ZD / 60PH672V-ZC (CHASSIS:PD32C) Service Manual ▷ View online
- 4 -
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
1. Application range
This spec sheet is applied all of the PDP TV with PD32C chassis.
2. Requirement for Test
Each part is tested as below without special appointment.
(1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F), CST: 40 °C ± 5 °C
(2) Relative Humidity: 65 % ± 10 %
(3) Power Voltage
: Standard input voltage (AC 100-240 V~, 50/60 Hz)
* Standard Voltage of each products is marked by models.
(4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with
BOM.
(5) The receiver must be operated for about 5 minutes prior to the adjustment.
3. Test method
(1) Performance: LGE TV test method followed
(2) Demanded other specification
- Safety : CE, IEC specification
- EMC : CE, IEC
4. Module General Specification
- 60" 3D FHD
No
Item
Specification
Remark
1
Display Screen Device
152 cm (60 inch) wide Color Display Module
PDP
2
Aspect Ratio
16:9
3
PDP Module
PDP60R5####,
RGB Closed (Well) Type, Glass Filter (43%)
Pixel Format: 1920 horiz. By 1080 ver.
4
Operating Environment 5) Temp. : 0 ~ 40 deg
6) Humidity : 20 ~ 80%
LGE SPEC
5
Storage Environment
7) Temp. : -20 ~ 60 deg
8) Humidity : 10 ~ 90 %
6
Input Voltage
AC220 ~ 240V, 50/60Hz
Maker LG
- 5 -
5. Model General Specification
No
Item
Specification
Remark
1
Market
Albania, Austria, Belgium, Bosnia, Bulgaria,
Coratia, Czech, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Ireland, Italy,
Kazakhstan, Latvia, Lithuania, Luxembourg,
Morocco, Netherlands, Norway, Poland, Portugal,
Romania, Russia, Serbia, Slovenia, Spain,
Sweden, Slovakia, Switzerland, Turkey, Ukraine, UK
36 Country
2
Broadcasting system
1) PAL/SECAM BG
2) PAL/SECAM DK
3) PAL I / II
4) SECAM L/L’
5) DVB T / T2
6) DVB C
7) DVB S/S2
EU (PAL Market)
Supporting T2/C/S is for **PH***V(U)
Supporting T/C/S is for **PH***S (R)
& **PH***8
3
Receiving system
Analog : Upper Heterodyne
Digital : COFDM
► DVB-T
- Guard Interval(Bitrate_Mbit/s)
1/4, 1/8, 1/16, 1/32
- Modulation : Code Rate
QPSK : 1/2, 2/3, 3/4, 5/6, 7/8
16-QAM : 1/2, 2/3, 3/4, 5/6, 7/8
64-QAM : 1/2, 2/3, 3/4, 5/6, 7/8
► DVB-C
- Symbolrate :
4.0Msymbols/s to 7.2Msymbols/s
- Modulation :
16QAM, 64-QAM, 128-QAM and 256-QAM
► DVB-S
- symbolrate
DVB-S2 (8PSK / QPSK) : 2 ~ 45Msymbol/s
DVB-S (QPSK) : 2 ~ 45Msymbol/s
- viterbi
DVB-S mode : 1/2, 2/3, 3/4, 5/6, 7/8
DVB-S2 mode : 1 /2, 2/3, 3/4, 3/5, 4/5, 5/6,
8/9, 9/10
4
Scart Jack (1EA)
PAL, SECAM
Scart 1 Jack is Full scart and support
RF-OUT(Analog), MNT-OUT
5
Video Input (1EA)
PAL, SECAM, NTSC
Rear Hybrid Jack Type
6
Component Input (1EA) Y/Cb/Cr, Y/ Pb/Pr
7
HDMI Input (3EA)
HDMI-PC
HDMI-DTV
HDMI-MHL
HDMI1(ARC), HDMI2(DVI) ,
Side HDMI3(MHL)
8
Audio Input (1EA)
Component + AV(Hybrid)
L/R Input
9
SPDIF Out (1 EA)
SPDIF Out
10
USB(3EA-FHD /
2 EA-HD )
For SVC, S/W Download, X-Studio, DivX
11
Ethernet LAN(1EA)
12
PCMCI (1EA)
Common Interface
- 6 -
ADJUSTMENT INSTRUCTION
1. Application Range
This spec. sheet applies to PD32C chassis applied PDP TV
all models manufactured in TV factory.
2. Specification
(1) Because this is not a hot chassis, it is not necessary to
use an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of
25 °C ± 5 °C of temperature and 65±10% of relative
humidity if there is no specific designation.
(4) The input voltage of the receiver must keep 100~240V,
50/60Hz.
(5) The receiver must be operated for about 5 minutes prior to
the adjustment when module is in the circumstance of over
15 °C
- In case of keeping module is in the circumstance of 0°C, it
should be placed in the circumstance of above 15°C for 2
hours
- In case of keeping module is in the circumstance of below
-20 °C, it should be placed in the circumstance of above 15
°C for 3 hours,.
■ After RGB Full White in HEAT-RUN Mode, the receiver must
be operated prior to the adjustment.
■ Enter into HEAT-RUN MODE
1) Press the POWER ON KEY on R/C for adjustment.
2) OSD display and screen display PATTERN MODE.
● Set is activated HEAT run without signal generator in this
mode.
● Single color pattern ( WHITE ) of HEAT RUN MODE uses to
check panel.
● Caution : If you turn on a still screen more than 20 minutes
(Especially digital pattern, cross hatch pattern), an
after image may be occur in the black level part of
the screen.
3. PCB Assembly adjustment
* Caution : Using ‘power on’ button of the control R/C power on
TV
3.1. Download MAC Address, CI+ Key and
widevine, ESN Key
* The CI+ Key download is need for only PD32A/B/C Models.
* Connect TV SET and PC which download keys Writing
program by RS232C-Cable
(1) Start Program and Click ‘start’ Button to connect TV and
PC.
(2) When download succeed, you can see “OK” on the
screen.
* Each Chassis has it’s own MAC Address. Please be careful
of download.
3.2. DFT Process
* Depend on situation, Step can be changed.
* Condition spec
3.3. Tool OPTION (MANUAL)
(1) Insert Access USB Memory Stick
(2) Press ADJ key on R/C to insert Tool OPTION
(3) On the “ Tool Option ”, Insert Tool Option by a number key
(4) Press the ENTER(■)
(5) Press ENTER(■) again.
(6) Select “OK to Download” by using ◄/►(VOL +/-) and
press ►(VOL +)
Model Name
PH6608 PH670V/672V PH660V
Tool
option 1
42
N/A
N/A
N/A
50
32854
32806
32854
60
32856
32808
32856
Tool
option 2
42 HD
N/A
N/A
N/A
50 HD
N/A
N/A
N/A
50 FHD
12306
12306
12306
60 FHD
12306
12306
12306
Tool option 3
162
162
162
Tool option 4
61754
61897
61897
Tool option 5
6341
6294
6341
Tool option 6
1609
1609
1609
Tool option 7
13455
13455
13455
Mode
Volume
Power Off
RF
0
DC On
- 7 -
3.4. EDID
(The Extended Display Identification Data)
■ HDMI [C/S: 9771] : For FHD Models
* CheckSum & Physical Address Table.
- Each HDMI Input has their own physical address(on
Address:9E). So, each HDMI Input has different C/S
value.
■ HDMI INPUT Physical Address Table
■ HDMI INPUT C/S Table.
- FHD
4. SET assembly adjustment method
* Caution: Each PCB assembly must be checked by check
JIG set. (Because power PCB Assembly damages
to PDP Module, especially be careful)
4.1. POWER PCB Assembly Voltage adjustment
(Va, Vs voltage adjustment)
Test equipment : D.M.M 1EA
Connection Diagram for Measuring : refer to fig.4
Adjustment method
4.1.1. Va adjustment
(1) Connect + terminal of D. M.M. to Va pin of P811, connect
-terminal to GND pin of P811.
(2) After turning VR502,voltage of D.M.M adjustment as same
as Va voltage which on label of panel right/top (deviation;
±0.5V)
4.1.2. Vs adjustment
(1) Connect + terminal of D. M..M. to Vs pin of P811, connect
-terminal to GND pin of P811.
(2) After turning VR901, voltage of D.M.M adjustment as
same as Vs voltage which on label of panel right/top (
deviation ; ±0.5V)
4.2. Adjustment of White Balance
- Required Equipment
● Remote controller for adjustment
● Color Analyzer ( CS-1000, CA-210 or same product
: CH 10 (PDP)
* Please adjust CA-210 by CS-1000 before measuring
● Auto W/B adjustment instrument(only for Auto
adjustment)
● 9 Pin D-Sub Jack(RS232C) is connected to the AUTO
W/B EQUIPMENT
Before Adjust of White Balance, Please press
POWER ONLY key
- Adjust Process will start by execute RS232C Command.
● Color temperature standards according to CSM and Module
● CS-1000/CA-100+/CA-210(CH 10) White balance adjust-
ment coordinates and color temperature.
Physical Address
Address
HDMI1
HDMI2
HDMI3
A1
10
20
30
HDMI1
HDMI2
HDMI3
CheckSum
9771
9761
9751
CSM
PLASMA
Cool
11000K
Medium
9300K
Warm
6500K
CSM
Color Coordination
Temp
± Color
Coordination
x
y
COOL
0.276
0.283
11000K
0.002
MEDIUM
0.285
0.293
9300K
0.002
WARM
0.313
0.329
6500K
0.002