DOWNLOAD LG 55LX950N-ZA (CHASSIS:LD03R) Service Manual ↓ Size: 5.55 MB | Pages: 54 in PDF or view online for FREE

- 13 -

(1) Auto adj. method

1) Set TV in adj. mode using POWER ON key.
2) Zero calibrate probe then place it on the center of the

Display.

3) Connect Cable (RS-232C)
4) Select mode in adj. Program and begin adjustment.
5) When adj. is complete (OK Sing), check adj. status pre

mode. (Warm, Medium, Cool)

6) Remove probe and RS-232C cable to complete adj.

A

W/B Adj. must begin as start command “wb 00 00” , and
finish as end command “wb 00 ff”, and Adj. offset if need.

(2) Manual adj. method

1) Set TV in Adj. mode using POWER ON
2) Zero Calibrate the probe of Color Analyzer, then place it

on the center of LCD module within 10cm of the surface.

3) Press ADJ key -> EZ adjust using adj. R/C -> 7. White-

Balance then press the cursor to the right (KEY 

G

).

(When KEY(

G

) is pressed 216 Gray internal pattern will

be displayed)

4) One of R Gain / G Gain / B Gain should be fixed at 192,

and the rest will be lowered to meet the desired value.

5) Adj. is performed in COOL, MEDIUM, WARM 3 modes

of color temperature.

A

If internal pattern is not available, use RF input. In EZ
Adj. menu 7.White Balance, you can select one of 2
Test-pattern: ON, OFF. Default is inner(ON). By
selecting OFF, you can adjust using RF signal in 216
Gray pattern.

A

Adj. condition and cautionary items

1) Lighting condition in surrounding area

Surrounding lighting should be lower 10 lux. Try to
isolate adj. area into dark surrounding.

2) Probe location

: Color Analyzer (CA-210) probe should be within
10cm and perpendicular of the module surface (80°~
100°)

3) Aging time

- After Aging Start, Keep the Power ON status during

5 Minutes.

- In case of LCD, Back-light on should be checked

using no signal or Full-white pattern.

A

Luminance : 216 Gray

A

Standard color coordinate and temperature using CS-1000
(over 26 inch)

A

Standard color coordinate and temperature using CA-
210(CH 9)

- In case of THX adjustment, it is automatically adjusted in

Warm mode of 5 point.

1) Adjustment of 100 IRE White Balance
2) Backlight adjustment to MAX 120 cd
3) Adjustment of Gamma2.2 each case of IRE(80, 60, 40, 20),

using 2) value.

4) In case of 10 IRE : R gain=0, G gain=0, B gain=0
5) Finish 5 point gamma & W/B adjustment.

A

IOP & Edge LED module change color coordinate because
of aging time.

A

apply under the color coordinate table, for compensated
aging time.

- IOP LED(LX95)

Mode

Color Coordination

Temp

∆UV

x

y

COOL

0.269

0.273

13000 K

0.0000

MEDIUM

0.285

0.293

9300 K

0.0000

WARM

0.313

0.329

6500 K

0.0000

Mode

Color Coordination

Temp

∆UV

x

y

COOL

0.269 ± 0.002

0.273 ± 0.002 13000 K

0.0000

MEDIUM

0.285 ± 0.002

0.293 ± 0.002

9300 K

0.0000

WARM

0.313 ± 0.002

0.329 ± 0.002

6500 K

0.0000

GP2

Aging Time

Cool

Medium

Warm

(Min.)

X

Y

X

Y

X

Y

269

273

285

293

313

329

1

0-2

287

301

303

321

326

351

2

3-5

286

299

302

319

325

349

3

6-9

285

297

301

317

324

347

4

10-19

283

295

299

315

322

345

5

20-35

281

291

297

311

320

341

6

36-49

277

285

293

305

316

335

7

50-79

273

281

289

301

312

331

8

80-149

271

277

287

297

310

327

9

OVER 150

269

273

285

293

308

323

- 14 -

Step 1) Connect set and Dongle of Wireless to Cable of HDMI

& TTA 20Pin

Step 2) At OSD of SET, check the message like Fig.3
Step 3) Detach Cable of Wireless Dongle

Step 1) Turn on TV
Step 2) Press EYE key of Adj. R/C
Step 3) Cover the Eye Q II sensor on the front of the using

your hand and wait for 6 seconds

Step 4) Confirm that R/G/B value is lower than 10 of the “Raw

Data (Sensor data, Back light)”. If after 6 seconds,
R/G/B value is not lower than 10, replace Eye Q II
sensor.

Step 5) Remove your hand from the Eye Q II sensor and wait

for 6 seconds.

Step 6) Confirm that “ok” pop up. If change is not seen,

replace Eye Q II sensor.

Step 1) Turn on TV.
Step 2) At the Local Dimming mode, module Edge Backlight

moving right to left Back light of IOP module moving.

Step 3) Confirm the Local Dimming mode.
Step 4) Press “exit” key

(47/55LX9500 only)
- Equipment : RF Remote control for test, IR-KEY-Code

Remote control for test

- You must confirm the battery power of RF-Remote control

before test(recommend that change the battery per every lot) 

- Sequence (test)

1) if you select the ‘start key(Mute)’ on the controller, you can

pairing with the TV SET.

2) You can check the cursor on the TV Screen, when select

the ‘OK Key’ on the controller 

3) You must remove the pairing with the TV Set by select

‘Vol+(STOP) Key’ on the controller

(Pattern Generator MSHG-600, MSPG-6100 [Support HDMI 1.4])
* HDMI mode No. 872, pattern No. 83)
1) Please input 3D test pattern like below

2) When 3D OSD appear automatically, then select OK button.

Fig . 1 

< Do ng le>

 

Fig . 3  Connect the Dongle

( Do ng le Co nnec t io n Disp lay)

 

Fig . 2 

< Wireless Read y Set >

 

Connect

Local Dimming Demo (Edge LED Model)

Local Dimming Demo (IOP Model)

- 15 -

3) Don’t wear a 3D Glasses, Check the picture like below.

(1) Start 3D pattern inspection
(2) If IR emitter emitter signal is correctly received to IR

receiver, the lamp of IR tester turn on

(1) Overview

- Option selection is only done for models in Non-EU.
- Applied model: LD03D/03E Chassis applied EU model.

(2) Method

1) Press ADJ key on the Adj. Remote Control, then select

Country Group Menu.

2) Depending on destination, select Country Group Code

04 or Country Group EU then on the lower Country
option, select US, CA, MX. Selection is done using +, -
or 

GF

KEY.

- Method : Press Adj. key on the Adj. Remote Control, then

select Tool option.

After final inspection, press IN-STOP key of the Adj. R/C and
check that the unit goes to Stand-by mode.

- Check that Power Cord is fully inserted to the SET.

(If loose, re-insert)

- Unit fully inserted Power cord, Antenna cable and A/V

arrive to the auto-check process. 

- Connect D-terminal to AV JACK TESTER
- Auto CONTROLLER(GWS103-4) ON
- Perform GND TEST
- If NG, Buzzer will sound to inform the operator.
- If OK, changeover to I/P check automatically.

(Remove CORD, A/V form AV JACK BOX)

- Perform I/P test
- If NG, Buzzer will sound to inform the operator.
- If OK, Good lamp will lit up and the stopper will allow the

pallet to move on to next process.

• TEST voltage

- GND: 1.5KV/min at 100mA
- SIGNAL: 3KV/min at 100mA

• TEST time: 1 second
• TEST POINT

- GND TEST = POWER CORD GND & SIGNAL CABLE

METAL GND

NEUTRAL

• LEAKAGE CURRENT: At 0.5mArms

Measurement condition:
1. RF input: Mono, 1KHz sine wave signal, 100% Modulation
2. CVBS, Component: 1KHz sine wave signal 0.4Vrms
3. RGB PC: 1KHz sine wave signal 0.7Vrms

<IR Tester Lamp turned off(NG)>

<IR Emitter inspection>

<IR Tester Lamp turned on(OK)>

No.

Item

Min. Typ. Max. Unit

1.  Audio practical max

4.5

5

6

W

EQ Off

Output, L/R

AVL Off

(Distortion=10 %

6.33 6.93 Vrms Clear Voice Off

max Output)

2. Speaker 

(8 

Ω

5

7

W

EQ On

Impedance)

AVL On

Clear Voice On

Mode

Tool 1

Tool 2

Tool 3

Tool 4

Tool 5

55LX9500

46080

31795

54588

22956

2995

- 16 -

1) Put the USB Stick to the USB socket 
2) Automatically detecting update file in USB Stick

- If your downloaded program version in USB Stick is Low,

it didn’t work. But your downloaded version is High, USB
data is automatically detecting

3) Show the message “Copying files from memory”

4) Updating is starting.

5) Updating Completed, The TV will restart automatically
6) If your TV is turned on, check your updated version and

Tool option. (explain the Tool option, next stage)

* If downloading version is more high than your TV have,

TV can lost all channel data. In this case, you have to
channel recover. if all channel data is cleared, you didn’t
have a DTV/ATV test on production line.

* After downloading, have to adjust TOOL OPTION again.

1) Push "IN-START" key in service remote control.
2) Select "Tool Option 1" and Push “OK” button.
3) Push in the number. (Each model has their number.)