DOWNLOAD LG 55LX6500-TD (CHASSIS:LB03R) Service Manual ↓ Size: 11.31 MB | Pages: 110 in PDF or view online for FREE

- 13 -

(1) Auto adj. method

1) Set TV in adj. mode using POWER ON key.
2) Zero calibrate probe then place it on the center of the

Display.

3) Connect Cable (RS-232C)
4) Select mode in adj. Program and begin adjustment.
5) When adj. is complete (OK Sing), check adj. status pre

mode. (Warm, Medium, Cool)

6) Remove probe and RS-232C cable to complete adj.

A

W/B Adj. must begin as start command “wb 00 00” , and
finish as end command “wb 00 ff”, and Adj. offset if need.

(2) Manual adj. method

1) Set TV in Adj. mode using POWER ON
2) Zero Calibrate the probe of Color Analyzer, then place it

on the center of LCD module within 10cm of the surface.

3) Press ADJ key -> EZ adjust using adj. R/C -> 7. White-

Balance then press the cursor to the right (KEY 

G

).

(When KEY(

G

) is pressed 216 Gray internal pattern will

be displayed)

4) One of R Gain / G Gain / B Gain should be fixed at 192,

and the rest will be lowered to meet the desired value.

5) Adj. is performed in COOL, MEDIUM, WARM 3 modes

of color temperature.

A

If internal pattern is not available, use RF input. In EZ
Adj. menu 7.White Balance, you can select one of 2
Test-pattern: ON, OFF. Default is inner(ON). By
selecting OFF, you can adjust using RF signal in 216
Gray pattern.

A

Adj. condition and cautionary items

1) Lighting condition in surrounding area

Surrounding lighting should be lower 10 lux. Try to
isolate adj. area into dark surrounding.

2) Probe location

: Color Analyzer (CA-210) probe should be within 10
cm and perpendicular of the module surface (80° ~
100°)

3) Aging time

- After Aging Start, Keep the Power ON status during

5 Minutes.

- In case of LCD, Back-light on should be checked

using no signal or Full-white pattern.

A

Luminance : 216 Gray

A

Standard color coordinate and temperature using CS-1000
(over 26 inch)

A

Standard color coordinate and temperature using CA-210
(CH 14)

A

10 Point White Balance

A

Color coordinate Variation by Aging time.

Step 1) Turn on TV
Step 2) Press EYE key of Adj. R/C
Step 3) Cover the Eye Q II sensor on the front of the using

your hand and wait for 6 seconds

Step 4) Confirm that R/G/B value is lower than 10 of the “Raw

Data (Sensor data, Back light)”. If after 6 seconds,
R/G/B value is not lower than 10, replace Eye Q II
sensor.

Step 5) Remove your hand from the Eye Q II sensor and wait

for 6 seconds.

Step 6) Confirm that “ok” pop up. If change is not seen,

replace Eye Q II sensor.

Mode

Color Coordination

Temp

∆UV

x

y

COOL

0.269

0.273

13000 K

0.0000

MEDIUM

0.285

0.293

9300 K

0.0000

WARM

0.313

0.329

6500 K

0.0000

Mode

Color Coordination

Temp

∆UV

x

y

COOL

0.269 ± 0.002

0.273 ± 0.002 13000 K

0.0000

MEDIUM

0.285 ± 0.002

0.293 ± 0.002

9300 K

0.0000

WARM

0.313 ± 0.002

0.329 ± 0.002

6500 K

0.0000

Edge

Aging Time

Cool

Medium

Warm

LED

(Min.)

X

Y

X

Y

X

Y

269

273

285

293

313

329

1

0-2

280

291

296

311

319

340

2

3-5

278

288

294

308

317

338

3

6-9

276

285

292

305

315

335

4

10-15

274

282

290

302

313

332

5

20-35

273

279

289

299

312

329

6

36-49

270

276

287

296

310

326

7

50-79

269

273

286

293

308

323

8

Over 80

269

273

285

293

308

323

On / Off

On / Off

Pattern

Outer(default)

IRE

100

Luminance

130

Red(130.0 nit)

0

Green(130.0 nit)

0

Blue(130.0 nit)

0

- 14 -

- Auto checking

• Auto checking is doing in “Power Only”.
• Checking the result of searched (check that is in list or not)
• Go out of checking mode pushing button “Exit”.

- Manual checking

• Push the button “Power Only” and “Exit”.
• Push the button hot key “Bluetooth”.
• Checking the result of searched (check that is in list or not)
• Go out of checking mode pushing button “Exit.

• Dimming checking is doing in “Power Only” using adjusts

Remote control.

• Push the button “Tilt”.
• Checking the function of Dimming refer to the picture at below.
• Push the button “Exit”.

* Edge LED models with local dimming

Press “TILT” key of the Adj. Remote control and check moving
patterns. The black bar patterns moves from left to right.
If local dimming function does not work. a whole screen

shows full white.

- Check that Power Cord is fully inserted to the SET.

(If loose, re-insert)

- Unit fully inserted Power cord, Antenna cable and A/V

arrive to the auto-check process. 

- Connect D-terminal to AV JACK TESTER
- Auto CONTROLLER(GWS103-4) ON
- Perform GND TEST
- If NG, Buzzer will sound to inform the operator.
- If OK, changeover to I/P check automatically.

(Remove CORD, A/V form AV JACK BOX)

- Perform I/P test
- If NG, Buzzer will sound to inform the operator.
- If OK, Good lamp will lit up and the stopper will allow the

pallet to move on to next process.

• TEST voltage

- GND: 1.5 KV / min at 100 mA
- SIGNAL: 3 KV / min at 100 mA

• TEST time: 1 second
• TEST POINT

- GND TEST = POWER CORD GND & SIGNAL CABLE

METAL GND

NEUTRAL

• LEAKAGE CURRENT: At 0.5 mArms

Measurement condition:
1. RF input: Mono, 1 KHz sine wave signal, 100 % Modulation
2. CVBS, Component: 1 KHz sine wave signal 0.4 Vrms
3. RGB PC: 1 KHz sine wave signal 0.7 Vrms

Local Dimming Demo (Edge LED Model)

Local Dimming Demo (IOP Model)

No.

Item

Min.

Typ.

Max.

Unit

1. 

Audio practical max

9.0

10.0

12.0

W

EQ Off

Output, L/R

AVL Off

(Distortion=10 %

8.5

8.9

9.8

Vrms

Clear Voice Off

max Output)

2. 

Speaker (8 Ω

10.0

15.0

W

EQ On

Impedance)

AVL On

Clear Voice On

- 15 -

1) Put the USB Stick to the USB socket 
2) Automatically detecting update file in USB Stick

- If your downloaded program version in USB Stick is Low,

it didn’t work. But your downloaded version is High, USB
data is automatically detecting

3) Show the message “Copying files from memory”

4) Updating is starting.

5) Updating Completed, The TV will restart automatically
6) If your TV is turned on, check your updated version and

Tool option. (explain the Tool option, next stage)

* If downloading version is more high than your TV have, TV

can lost all channel data. In this case, you have to channel
recover. if all channel data is cleared, you didn’t have a
DTV/ATV test on production line.

* After downloading, have to adjust TOOL OPTION again.

1) Push "IN-START" key in service remote control.
2) Select "Tool Option 1" and Push “OK” button.
3) Push in the number. (Each model has their number.)

(Pattern Generator MSPG-3233, HDMI mode No. 371, pattern
No. 81)
1) Please input 3D test pattern like below

2) Enter 3D mode, then select side by side

(If you don’t wear a 3D Glasses, you will see the picture
like below)

3) Put on the 3D Glasses, And block the right side of Glasses 

(LEFT:OPEN[TEST], RIGHT:CLOSED)
And check the middle sides of picture, RED -> normal,
others -> abnormal

4) Put on the 3D Glasses, And block the right side of Glasses 

(LEFT:CLOSED, RIGHT:OPEN[TEST])
And check the middle sides of picture, BLUE -> normal,
others -> abnormal

- 16 -

300

500

120

200

LV1

LV2

840

820

820

520

880

830

530

540

541

850

710

800

A13

A10

A21

A9

A5

A2

810

400

570

910

900

920

580

310

510

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These
parts are identified by       in the Schematic Diagram and EXPLODED VIEW. 
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. 
Do not modify the original design without permission of manufacturer.