DOWNLOAD LG 55LV555H (CHASSIS:LA05E) Service Manual ↓ Size: 6.08 MB | Pages: 41 in PDF or view online for FREE

- 13 -

5.1.1 Overview 

ADC adjustment is needed to find the optimum black level
and gain

5.1.2 Equipment & Condition 

1) Adjust Remocon 
2) 801GF(802B, 802F, 802R) or MSPG925FA Pattern

Generator 

- Resolution: 480i, 1024*768 
- Pattern : Horizontal 100% Color Bar Pattern 
- Pattern level: 0.7±0.1 Vp-p 
- Image 

3)  Must use standard cable 

5.1.3 Adjust method  

5.1.3.1 ADC 480i Comp1 
1) Check connected condition of Comp1 cable to the

equipment 

2) Give a 480i Mode, Horizontal 100% Color Bar Pattern to

Comp1. 

(MSPG-925FA  ->  Model: 209, Pattern: 65) 

3) Change input mode as Component1 and picture mode

as “Standard” 

4) Press the In-start Key on the ADJ remote after at least 1

min of signal reception. Then, select 7. External ADC ->
1. COMP 480i on the menu. Press enter key. The
adjustment will start automatically. 

5) If ADC calibration is successful, “ADC RGB Success” is

displayed. If ADC calibration is failure, “ADC RGB Fail”
is displayed. 

6) If ADC calibration is failure, after recheck ADC pattern or

condition retry calibration Error message refer to 

5.1.3.2 ADC 1080p Comp1 
1) Check connected condition of Comp1 cable to the

equipment 

2) Give a 1080p Mode, Horizontal 100% Color Bar Pattern

to Comp1. 

(MSPG-925FA -> Model: 225, Pattern: 65) 

3) Change input mode as Component1 and picture mode

as “Standard” 

4) Press the In-start Key on the ADJ remote after at least 1

min of signal reception. Then, select 7. External ADC ->
1. COMP 1080P on the menu. Press enter key. The
adjustment will start automatically. 

5) If ADC calibration is successful, “ADC RGB Success” is

displayed. If ADC calibration is failure, “ADC RGB Fail”
is displayed. 

6) If ADC calibration is failure, after recheck ADC pattern or

condition retry calibration Error message refer to 

5.1.3.2 ADC 1024*768 RGB 
1) Check connected condition of Component & RGB cable

to the equipment 

2) Give a 1024*768 Mode, 100% Horizontal Color Bar

Pattern to RGB port.  

(MSPG-925 Series  model:60 , pattern:65 ) 
3) Change input mode as RGB and picture mode as

“Standard” 

4) Press the In-start Key on the ADJ remote after at least 1

min of signal reception. Then, select 7. External ADC ->
1. COMP 480i on the menu. Press enter key. The
adjustment will start automatically. 

5) If ADC calibration is successful, “ADC RGB Success” is

displayed. If ADC calibration is failure, “ADC RGB Fail”
is displayed. 

6) If ADC calibration is failure, after recheck ADC pattern or

condition retry calibration Error message refer to 5) 

Reference : Download is only possible in POWER ONLY

MODE 

5.2.1 Overview  

It is a VESA regulation. A PC or a MNT will display an
optimal resolution through information sharing without any
necessity of user input. It is a realization of “Plug and Play”

5.2.2 Equipment  

• Since embedded EDID data is used, EDID download JIG,

HDMI cable and D-sub cable are not need. 

• Adjust remocon 

5.2.3 Download method   

1) Press Adj. key on the Adj. R/C, 
2) Select EDID D/L menu. 
3) By pressing Enter key, EDID download will begin 
4) If Download is successful, OK is display, but If

Download is failure, NG is displayed. 

5) If Download is failure, Re-try download. 

• Caution) When EDID Download, must remove

RGB/HDMI Cable. 

- 14 -

5.2.4 EDID DATA 

•  HDMI I [C/S: F591]    
EDID Block 0  table = 

EDID Block 1  table = 

•  HDMIII [C/S: F581]     
EDID Block 0  table = 

EDID Block 1  table = 

•  RGB   [C/S: DE]     
EDID Block 0  table = 

- 15 -

(1) Overview

• W/B adj. Objective & How-it-works

- Objective: To reduce each Panel’s W/B deviation
- How-it-works: When R/G/B gain in the OSD is at 192, it

means the panel is at its Full Dynamic
Range. In order to prevent saturation of
Full Dynamic range and data, one of
R/G/B is fixed at 192, and the other two is
lowered to find the desired value.   

- Adj. condition : normal temperature

1) Surrounding Temperature: 25±5ºC
2) Warm-up time: About 5 Min
3) Surrounding Humidity: 20% ~ 80%

(2) Equipment

1) Color Analyzer: CA-210 (NCG: CH 9 / WCG: CH12)
2) Adj. Computer(During auto adj., RS-232C protocol is

needed)

3) Adjust Remocon
4) Video Signal Generator MSPG-925F 720p/216-Gray

(Model:217, Pattern:78)

-> Only when internal pattern is not available

• Color Analyzer Matrix should be calibrated using CS-1000

(3) Equipment connection MAP

(4) Adj. Command (Protocol)

1) RS-232C Command used during auto-adj.

Ex) wb 00 00   ->  Begin white balance auto-adj.

wb 00 10   ->  Gain adj.
ja 00 ff   ->  Adj. data
jb 00 c0
...

...

wb 00 1f   -> Gain adj. complete
*(wb 00 20(start), wb 00 2f(end)) -> Off-set adj.
wb 00 ff   -> End white balance auto adj.

2) Adjustment Map
Applied Model : LA02B Chassis ALL MODELS 

(5) Auto adj. method

1) Set TV in adj. mode using POWER ON key
2) Zero calibrate probe then place it on the center of the

Display

3) Connect Cable(RS-232C)
4) Select mode in adj. Program and begin adj.
5) When adj. is complete (OK Sing), check adj. status pre

mode (Warm, Medium, Cool)

6) Remove probe and RS-232C cable to complete adj.

* W/B Adj. must begin as start command “wb 00 00” , and

finish as end command “wb 00 ff”, and Adj. offset if need 

(6) Manual adj. method

1) Set TV in Adj. mode using POWER ON
2) Zero Calibrate the probe of Color Analyzer, then place

it on the center of LCD module within 10cm of the
surface..

3) Press ADJ key -> EZ adjust using adj. R/C > 6. White-

Balance then press the cursor to the right (KEY

G

).

(When KEY(

G

) is pressed 216 Gray internal pattern

will be displayed)

4) One of R Gain / G Gain / B Gain should be fixed at

192, and the rest will be lowered to meet the desired
value.

5) Adj. is performed in COOL, MEDIUM, WARM 3 modes

of color temperature.

- If internal pattern is not available, use RF input. In EZ

Adj. menu 6.White Balance, you can select one of 2
Test-pattern: ON, OFF. Default is inner(ON). By
selecting OFF, you can adjust using RF signal in 216
Gray pattern.

Co lo r An alyzer

 

Co m p ut er

 

Pat t ern Gen erat o r

 

RS -232C 

RS -232C 

RS -232C 

Probe

Signal Source

* If TV internal pattern is used, not needed

Connection Diagram of Automatic Adjustment

RS-232C COMMAND

Meaning

[CMD

ID

DATA]

wb

00

00

Begin White Balance adj.

wb

00

ff

ITEM

Command

Data Range

Default

(Hex.)

(Decimal)

Cmd 1

Cmd 2

Min

Max

Cool

R-Gain

j

g

00

C0

G-Gain

j

h

00

C0

B-Gain

j

i

00

C0

R-Cut

G-Cut

B-Cut

Medium

R-Gain

j

a

00

C0

G-Gain

j

b

00

C0

B-Gain

j

c

00

C0

R-Cut

G-Cut

B-Cut

Warm

R-Gain

j

d

00

C0

G-Gain

j

e

00

C0

B-Gain

j

f

00

C0

R-Cut

G-Cut

- 16 -

* Adj. condition and cautionary items

1) Lighting condition in surrounding area

Surrounding lighting should be lower 10 lux. Try to
isolate adj. area into dark surrounding.

2) Probe location

- LCD: Color Analyzer (CA-210) probe should be

within 10cm and perpendicular of the module
surface (80°~ 100°)

3) Aging time

- After Aging Start, Keep the Power ON status during 5

Minutes.

- In case of LCD, Back-light on should be checked

using no signal or Full-white pattern.

(7) Reference (White Balance Adj. coordinate and color

temperature)

1) W/B Equipment condition

CA210 CCFL/EEFL -> CH9, Test signal, Inner
pattern(80IRE)
LED(AUO) -> CH14, Test signal, Inner pattern(80IRE)

2) Above 5 minutes H/run in the inner pattern. (“Powre on”

key of adjust remote control)

• Edge LED W/B Table in process of time(Only LGD

module)

CA210 : CH14, Test signal : Inner pattern(80IRE)

- HDCP setting is not necessary in This Chassis.  

For downloading the MAC address which be allotted on
each LAN Card. 

5.5.1 Adjustment Method  

1)  Connecting the TV set and the PC which has MAC

Address Writing program through  The RS232C cable.  

2)  Editing the macaddress.txt 
(Inserting start MAC address at top low. )
(Inserting start MAC address at bottom low. )

Launch MAC Address Writing program and set just like

below picture.(1) 

3) Click the LOAD button for reading the MAC address.(2) 

(SAVE : Saving the current MAC Address      

CLEAR : Initializing the space which insert MAC

Address. )

4) Click  the  “ MAC Address” button to write current MAC

Address.(3) 

5)  In case of being downloaded normally, you can see the

(4) message with “ OK” in the window.  

6) In case of being downloaded normally, MAC address

increased one by one  automatically. So the next set,
just click the “ MAC Address‚  ” button after  connecting
the port. 

(Whenever be finished, the program saves the MAC
Address in “ macaddress.txt” file automatically.) 

Color

Temperature

Cool

Medium

Warm

13,000k

K

X=0.269(±0.002)
Y=0.273(±0.002)

<Test Signal>

Inner pattern

(204gray,

80IRE)

X=0.285(±0.002)
Y=0.293(±0.002)

X=0.313(±0.002)
Y=0.329(±0.002)

K

K

9,300k

6,500k

GP2

1

2

3

4

5

6

7

8

9

0-2

3-5

6-9

10-19

20-35

36-49

50-79

80-149

Over 150

279

278

277

276

274

272

271

270

269

288

286

285

283

280

277

275

274

273

295

294

293

292

290

288

287

286

285

308

306

305

303

300

297

295

294

293

319

318

317

316

314

312

311

310

309

338

336

335

333

330

327

325

324

323

Aging Time

(Min)

Cool

x

269

273

285

293

313

329

y

x

y

x

y

Medium

Warm