LG 55LV5300 (CHASSIS:LA01U) Service Manual ▷ View online
- 9 -
ADJUSTMENT INSTRUCTION
1. Application range
This spec. sheet applies to LA01U / LA01T / LA01S Chassis
applied LED LCD TV all models manufactured in TV factory.
applied LED LCD TV all models manufactured in TV factory.
2. Specification
2.1 Because this is not a hot chassis, it is not necessary
to use an isolation transformer. However, the use of
isolation transformer will help protect test instrument.
isolation transformer will help protect test instrument.
2.2 Adjustment must be done in the correct order.
2.3 The adjustment must be performed in the
2.3 The adjustment must be performed in the
circumstance of 25±5°C of temperature and 65±10%
of relative humidity
of relative humidity
2.4 The input voltage of the receiver must keep
100~240V~, 50/60Hz.
2.5 At first Worker must turn on the SET by using Power
Only key.
2.5 The receiver must be operated for about 5 minutes
prior to the adjustment when module is in the
circumstance of over 15.
circumstance of over 15.
In case of keeping module is in the circumstance of
0°C, it should be placed in the circumstance of above
15°C for 2 hours
0°C, it should be placed in the circumstance of above
15°C for 2 hours
In case of keeping module is in the circumstance of
below -20°C, it should be placed in the circumstance
of above 15°C for 3 hours.
below -20°C, it should be placed in the circumstance
of above 15°C for 3 hours.
• Caution
When a still image is displayed for 20 minutes or longer
(especially where W/B scale is strong. Digital pattern 13ch
and/or Cross hatch pattern 09ch), there can some
afterimage in the black level area.
When a still image is displayed for 20 minutes or longer
(especially where W/B scale is strong. Digital pattern 13ch
and/or Cross hatch pattern 09ch), there can some
afterimage in the black level area.
3. Adjustment items
3.1 Board Level Adjustment
(1) ADC adjustment: Component 480i, 1080p / RGB-PC 1080p
(2) EDID downloads for HDMI and RGB-PC
(2) EDID downloads for HDMI and RGB-PC
• Remark
- Above adjustment items can be also performed in Final
Assembly if needed. Adjustment items in both PCBA and
final assembly stages can be checked by using the
INSTART Menu 1.ADJUST CHECK.
final assembly stages can be checked by using the
INSTART Menu 1.ADJUST CHECK.
3.2 Final Assembly adjustment
(1) White Balance adjustment
(2) RS-232C functionality check
(3) Factory Option setting per destination
(4) Shipment mode setting (IN-STOP)
(2) RS-232C functionality check
(3) Factory Option setting per destination
(4) Shipment mode setting (IN-STOP)
3.3 Etc
(1) Ship-out mode
(2) Service Option Default
(3) USB Download(S/W Update, Option, Service only)
(4) ISP Download (Optional)
(2) Service Option Default
(3) USB Download(S/W Update, Option, Service only)
(4) ISP Download (Optional)
4. Board Level Adjustment
4.1. ADC Adjustment
4.1.1. Overview
• ADC adjustment is needed to find the optimum black level
• ADC adjustment is needed to find the optimum black level
and gain in Analog-to-Digital device and to compensate RGB
deviation.
deviation.
4.1.2. Equipment & Condition
1) Jig (RS-232C protocol)
2) Inner Pattern
1) Jig (RS-232C protocol)
2) Inner Pattern
- Resolution : 1080p (Inner Pattern)
- Resolution : 1024*768 RGB (Inner Pattern)
- Pattern : Horizontal 100% Color Bar Pattern
- Pattern level : 0.7±0.1 Vp-p
- Resolution : 1024*768 RGB (Inner Pattern)
- Pattern : Horizontal 100% Color Bar Pattern
- Pattern level : 0.7±0.1 Vp-p
4.1.3. Adjustment
4.1.3.1 Adjustment method
• Using RS-232, adjust items listed in 3.1 in the other
• Using RS-232, adjust items listed in 3.1 in the other
shown in “4.1.3.3”
4.1.3.2 Adj. protocol
Ref.) ADC Adj. RS232C Protocol_Ver1.0
4.1.3.3. Adj. order
• aa 00 00 [Enter ADC adj. mode]
• xb 00 40 [Change input source to Component1(1080i)]
• ad 00 10 [Adjust 480i Comp1]
• xb 00 60 [Change input source to RGB(1024*768)]
• ad 00 10 [Adjust 1024*768 RGB]
• ad 00 90 End adj.
• aa 00 00 [Enter ADC adj. mode]
• xb 00 40 [Change input source to Component1(1080i)]
• ad 00 10 [Adjust 480i Comp1]
• xb 00 60 [Change input source to RGB(1024*768)]
• ad 00 10 [Adjust 1024*768 RGB]
• ad 00 90 End adj.
Ref) ADC adj. RS232C Protocol_Ver1.0
Protocol
Command
Set ACK
Enter adj. mode
aa 00 00
a 00 OK00x
Source change
xb 00 40
xb 00 60
xb 00 60
b 00 OK40x (Adjust 480i /1080p Comp1 )
b 00 OK60x (Adjust 1920*1080 RGB)
b 00 OK60x (Adjust 1920*1080 RGB)
Begin adj.
ad 00 10
Return adj. result
OKx (Case of Success)
NGx (Case of Fail)
NGx (Case of Fail)
Read adj. data
(main)
ad 00 20
(sub )
ad 00 21
ad 00 20
(sub )
ad 00 21
(main)
000000000000000000000000007c007b006dx
(Sub)
000000070000000000000000007c00830077x
000000000000000000000000007c007b006dx
(Sub)
000000070000000000000000007c00830077x
Confirm adj.
ad 00 99
NG 03 00x (Fai l)
NG 03 01x (Fai l)
NG 03 02x (Fai l)
OK 03 03x (Success)
NG 03 01x (Fai l)
NG 03 02x (Fai l)
OK 03 03x (Success)
End adj.
aa 00 90
a 00 OK90x
- 10 -
4.2. EDID/DDC Download
4.2.1 Overview
• It is a VESA regulation. A PC or a MNT will display an
• It is a VESA regulation. A PC or a MNT will display an
optimal resolution through information sharing without any
necessity of user input. It is a realization of “Plug and Play”.
necessity of user input. It is a realization of “Plug and Play”.
4.2.2 Equipment
• Since embedded EDID data is used, EDID download JIG,
• Since embedded EDID data is used, EDID download JIG,
HDMI cable and D-sub cable are not need.
• Adjust remocon.
4.2.3 Download method
1) Press Adj. key on the Adj. R/C,
2) Select EDID D/L menu.
3) By pressing Enter key, EDID download will begin
4) If Download is successful, OK is display, but If Download is
1) Press Adj. key on the Adj. R/C,
2) Select EDID D/L menu.
3) By pressing Enter key, EDID download will begin
4) If Download is successful, OK is display, but If Download is
failure, NG is displayed.
5) If Download is failure, Re-try downloads.
* Caution) When EDID Download, must remove RGB/HDMI
Cable.
Block1
# HDMI2-EDID (C/S : 03BC)
Block0
Block0
Block1
# HDMI3-EDID (C/S : 03AC)
Block0
Block0
Block1
# RGB-EDID (C/S : 1C)
Block0
Block0
0 1 2 3 4 5 6 7 8 9 A B C D E F
_______________________________________________________
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 | 01 15 01 03 80 10 09 78 0A EE 91 A3 54 4C 99 26
20 | 0F 50 54 A1 08 00 81 80 61 40 45 40 31 40 01 01
30 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C
40 | 45 00 A0 5A 00 00 00 1E 01 1D 00 72 51 D0 1E 20
50 | 6E 28 55 00 A0 5A 00 00 00 1E 00 00 00 FD 00 39
60 | 3F 1F 52 10 00 0A 20 20 20 20 20 20 00 00 00 FC
70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 03
0 1 2 3 4 5 6 7 8 9 A B C D E F
_______________________________________________________
0 | 02 03 1C F1 47 10 22 20 05 84 03 02 23 09 07 07
10 | 67 03 0C 00 10 00 B8 2D E3 05 03 01 02 3A 80 18
20 | 71 38 2D 40 58 2C 04 05 A0 5A 00 00 00 1E 01 1D
30 | 80 18 71 1C 16 20 58 2C 25 00 A0 5A 00 00 00 9E
40 | 01 1D 00 72 51 D0 1E 20 6E 28 55 00 A0 5A 00 00
50 | 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 A0 5A
60 | 00 00 00 18 26 36 80 A0 70 38 1F 40 30 20 25 00
70 | A0 5A 00 00 00 1A 00 00 00 00 00 00 00 00 00 CC
0 1 2 3 4 5 6 7 8 9 A B C D E F
______________________________________________________
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 | 01 15 01 03 80 10 09 78 0A EE 91 A3 54 4C 99 26
20 | 0F 50 54 A1 08 00 81 80 61 40 45 40 31 40 01 01
30 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C
40 | 45 00 A0 5A 00 00 00 1E 01 1D 00 72 51 D0 1E 20
50 | 6E 28 55 00 A0 5A 00 00 00 1E 00 00 00 FD 00 39
60 | 3F 1F 52 10 00 0A 20 20 20 20 20 20 00 00 00 FC
70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 03
0 1 2 3 4 5 6 7 8 9 A B C D E F
_______________________________________________________
0 | 02 03 1C F1 47 10 22 20 05 84 03 02 23 09 07 07
10 | 67 03 0C 00 20 00 B8 2D E3 05 03 01 02 3A 80 18
20 | 71 38 2D 40 58 2C 04 05 A0 5A 00 00 00 1E 01 1D
30 | 80 18 71 1C 16 20 58 2C 25 00 A0 5A 00 00 00 9E
40 | 01 1D 00 72 51 D0 1E 20 6E 28 55 00 A0 5A 00 00
50 | 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 A0 5A
60 | 00 00 00 18 26 36 80 A0 70 38 1F 40 30 20 25 00
70 | A0 5A 00 00 00 1A 00 00 00 00 00 00 00 00 00 BC
0 1 2 3 4 5 6 7 8 9 A B C D E F
________________________________________________________
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 | 01 15 01 03 80 10 09 78 0A EE 91 A3 54 4C 99 26
20 | 0F 50 54 A1 08 00 81 80 61 40 45 40 31 40 01 01
30 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C
40 | 45 00 A0 5A 00 00 00 1E 01 1D 00 72 51 D0 1E 20
50 | 6E 28 55 00 A0 5A 00 00 00 1E 00 00 00 FD 00 39
60 | 3F 1F 52 10 00 0A 20 20 20 20 20 20 00 00 00 FC
70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 03
0 1 2 3 4 5 6 7 8 9 A B C D E F
_______________________________________________________
0 | 02 03 1C F1 47 10 22 20 05 84 03 02 23 09 07 07
10 | 67 03 0C 00 30 00 B8 2D E3 05 03 01 02 3A 80 18
20 | 71 38 2D 40 58 2C 04 05 A0 5A 00 00 00 1E 01 1D
30 | 80 18 71 1C 16 20 58 2C 25 00 A0 5A 00 00 00 9E
40 | 01 1D 00 72 51 D0 1E 20 6E 28 55 00 A0 5A 00 00
50 | 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 A0 5A
60 | 00 00 00 18 26 36 80 A0 70 38 1F 40 30 20 25 00
70 | A0 5A 00 00 00 1A 00 00 00 00 00 00 00 00 00 AC
0 1 2 3 4 5 6 7 8 9 A B C D E F
_______________________________________________________
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 | 01 15 01 03 68 10 09 78 0A EE 91 A3 54 4C 99 26
20 | 0F 50 54 A1 08 00 81 80 61 40 45 40 31 40 01 01
30 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C
40 | 45 00 A0 5A 00 00 00 1E 01 1D 00 72 51 D0 1E 20
50 | 6E 28 55 00 A0 5A 00 00 00 1E 00 00 00 FD 00 3A
50 | 6E 28 55 00 A0 5A 00 00 00 1E 00 00 00 FD 00 3A
60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC
70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 00 1C
- 11 -
5. Final Assembly Adjustment
5.1. White Balance Adjustment
5.1.1. Overview
5.1.1.1. W/B adj. Objective & How-it-works
(1) Objective: To reduce each Panel’s W/B deviation
(2) How-it-works: When R/G/B gain in the OSD is at 192, it
5.1.1.1. W/B adj. Objective & How-it-works
(1) Objective: To reduce each Panel’s W/B deviation
(2) How-it-works: When R/G/B gain in the OSD is at 192, it
means the panel is at its Full Dynamic Range. In order to
prevent saturation of Full Dynamic range and data, one of
R/G/B is fixed at 192, and the other two is lowered to find
the desired value.
prevent saturation of Full Dynamic range and data, one of
R/G/B is fixed at 192, and the other two is lowered to find
the desired value.
(3) Adj. condition: normal temperature
1) Surrounding Temperature: 25±5°C
2) Warm-up time: About 5 Min
3) Surrounding Humidity: 20% ~ 80%
1) Surrounding Temperature: 25±5°C
2) Warm-up time: About 5 Min
3) Surrounding Humidity: 20% ~ 80%
5.1.2. Equipment
(1) Color Analyzer: CA-210 (NCG: CH 9 / WCG: CH12 / LED:
(1) Color Analyzer: CA-210 (NCG: CH 9 / WCG: CH12 / LED:
CH14)
(2) Adj. Computer (During auto adj., RS-232C protocol is
needed)
(3) Adjust Remocon
(4) Video Signal Generator MSPG-925F 720p/204-Gray
(4) Video Signal Generator MSPG-925F 720p/204-Gray
(Model: 217, Pattern: 49)
• Color Analyzer Matrix should be calibrated using CS-1000
5.1.3. Equipment connection
5.1.4. Adjustment Command (Protocol)
(1) RS-232C Command used during auto-adj.
(1) RS-232C Command used during auto-adj.
Ex) wb 00 00 -> Begin white balance auto-adj.
wb 00 10 -> Gain adj.
ja 00 ff -> Adj. data
jb 00 c0
...
...
ja 00 ff -> Adj. data
jb 00 c0
...
...
wb 00 1f -> Gain adj. complete
*(wb 00 20(start), wb 00 2f(end)) -> Off-set adj.
wb 00 ff ->End white balance auto adj.
(2) Adj. Map
Applied Model :
32/37/42/47/55LV3500-UA , 32/26/22/19LV2500-UA ,
32/42/47LV3500-NA, 42/47LV4500-NA, 42/47/55LW4500-NA
Applied Model :
32/37/42/47/55LV3500-UA , 32/26/22/19LV2500-UA ,
32/42/47LV3500-NA, 42/47LV4500-NA, 42/47/55LW4500-NA
5.1.5. Adjustment method
5.1.5.1 Auto WB calibration
1) Set TV in adj. mode using POWER ONLY (P-ONLY) key
2) Zero calibrate probe then place it on the center of the
5.1.5.1 Auto WB calibration
1) Set TV in adj. mode using POWER ONLY (P-ONLY) key
2) Zero calibrate probe then place it on the center of the
Display
3) Connect Cable(RS-232C)
4) Select mode in adj. Program and begin adj.
5) When adj. is complete (OK Sing), check adj. status pre
4) Select mode in adj. Program and begin adj.
5) When adj. is complete (OK Sing), check adj. status pre
mode (Cool, Medium, Warm)
6) Remove probe and RS-232C cable to complete adj.
• W/B Adj. must begin as start command “wb 00 00” , and
finish as end command “wb 00 ff”, and Adj. offset if need
finish as end command “wb 00 ff”, and Adj. offset if need
5.1.5.2 Manual adj. method
1) Set TV in Adj. mode using POWER ON
2) Zero Calibrate the probe of Color Analyzer, then place it on
1) Set TV in Adj. mode using POWER ON
2) Zero Calibrate the probe of Color Analyzer, then place it on
the center of LCD module within 10cm of the surface..
3) Press ADJ key -> EZ adjust using adj. R/C 6. White-
Balance then press the cursor to the right (KEY
G
). (When
KEY(
G
) is pressed 204 Gray(80IRE) internal pattern will be
displayed)
4) One of R Gain / G Gain / B Gain should be fixed at 192,
and the rest will be lowered to meet the desired value.
5) Adj. is performed in COOL, MEDIUM, WARM 3 modes of
color temperature.
• If internal pattern is not available, use RF input. In EZ Adj.
menu 6.White Balance, you can select one of 2 Test-pattern:
ON, OFF. Default is inner(ON). By selecting OFF, you can
adjust using RF signal in 204 Gray pattern.
ON, OFF. Default is inner(ON). By selecting OFF, you can
adjust using RF signal in 204 Gray pattern.
Co lo r An alyzer
Co m p ut er
Pat t ern Gen erat o r
RS -232C
RS -232C
RS -232C
Probe
Signal Source
* If TV internal pattern is used, not needed
Connection Diagram of Automatic Adjustment
RS-232C COMMAND
[CMD ID
DATA]
Explanation
Wb
00
00
Begin White Balance adj.
Wb
00
ff
End White Balance adj. (internal pattern disappears )
Adj.
item Command
(lower case ASCII)
Data Range
(Hex.)
(Hex.)
Default
(Decimal)
(Decimal)
CMD1 CMD2 MIN MAX
R Gain
j
g
00
C0
172
G Gain
j
h
00
i
00
C0 172
B Gain
j
C0
192
R Cut
64
G
Cut
64
Cool
B
Cut
64
Medium
j a 00
C0
192
G Gain
j
b
00
C0
192
B Gain
R Gain
j c 00
C0
192
R
Cut
64
G
Cut
64
B
Cut
64
R Gain
j
d
00
C0
192
G Gain
j
e
00
C0
192
B Gain
j
f
00
C0
172
R
Cut
64
G
Cut
64
Warm
B
Cut
64
- 12 -
• Adj. condition and cautionary items
1) Lighting condition in surrounding area
1) Lighting condition in surrounding area
Surrounding lighting should be lower 10 lux. Try to isolate
adj. area into dark surrounding.
adj. area into dark surrounding.
2) Probe location : Color Analyzer (CA-210) probe should be
within 10cm and perpendicular of the module surface (80°~
100°)
100°)
3) Aging time
- After Aging Start, Keep the Power ON status during 5
- After Aging Start, Keep the Power ON status during 5
Minutes.
- In case of LCD, Back-light on should be checked using no
signal or Full-white pattern.
5.1.6 Reference (White Balance Adj. coordinate and color
temperature)
(1) Luminance: 204 Gray, 80IRE
(2) Standard color coordinate and temperature using CS-1000
(2) Standard color coordinate and temperature using CS-1000
(over 26 inch)
• Standard color coordinate and temperature using CA-
210(CH 9)
• Standard color coordinate and temperature using CA-
210(CH 14) – by aging time
Edge LED models (applied only LGD Module)
5.2 HDCP (High-Bandwidth Digital
Contents Protection) SETTING
5.3 Option selection per country
America due to rating
• Applied model: LA01U Chassis applied None USA
model(CANADA, MEXICO)
5.3.2 Method
(1) Press ADJ key on the Adj. R/C, and then select Country
(1) Press ADJ key on the Adj. R/C, and then select Country
Group Menu
(2) Depending on destination, select KR or US, then on the
lower Country option, select US, CA, MX. Selection is
done using +, - KEY
done using +, - KEY
5.4 Tool Option selection
• Method: Press Adj. key on the Adj. R/C, then select Tool
option.
Mode
Color Coordination
Temp
∆
UV
x
y
COOL
0.269
0.273
13000K
0.0000
MEDIUM
0.285
0.293
9300K
0.0000
WARM
0.313
0.329
6500K
0.0000
Mode
Color Coordination
Temp
∆
UV
x
y
COOL
0.269±0.002
0.273±0.002
13000K
0.0000
MEDIUM
0.285±0.002
0.293±0.002
9300K
0.0000
WARM
0.313+0.002
0.329±0.002
6500K
0.0000
Cool
Medium
Warm
x
y
x
y
x
y
GP2G
Aging time
(Min)
269
273
285
293
313
329
1 0-2 276
285
2 3-5 274
282
3 6-9 273
280
4 10-19 272
278
5 20-35 271
276
6 36-49 269
274
7 50-79 269
273
8 Over
80 269
273
292
305
315 334
290
302
313 332
289
300
312 330
288
298
311 328
287
296
310 326
286
294
309 324
286
293
308 323
285
293
308 323
Model
Tool 1
Tool 2
Tool 3
Tool 4
Tool 5
Menu
32LV3500(20)-UA(B) 18280
19478
55337
2844 16738 AUO
37LV3500-UA 22376
19478
55338
2844
16738
AUO
42LV3500(20)-UA(B) 26472
19478
55338
2844 16736 AUO
42LV3500-UA
26468 19478 55337
2844 16425 CMI
47LV3500-UA
34656 19478 55337
2844 16640 LGD
55LV3500-UA
46944 19478 55338
2844 24832 LGD
32LV2500-UA
18213 18954 55332
2829 16425 CMI
32LV2500-UA
18216 19478 55337
2844 16738 AUO
42LV4500-NA 26406
19478
55337
2840
24576
LGD
47LV4500-NA 34688
19478
55337
2840
24576
LGD
42LW4500-NA 26528
19478
55337
2968
8192
LGD
47LW4500-NA 34720
19478
55337
2968
8192
LGD
55LW4500-NA 47008
19478
55337
2968
8192
LGD
47LV3500(1,20)-NA(B,C) 34656 19478 55337
2840 16384 LGD
42LV3500(1,20)-NA(B,C) 26464 19478 55337
2840 16416 LGD
32LV3500-NA
18272 19478 55337
2840 16418 LGD
26LV2500-UA 14120
18954
55338
2844
16640
AUO
22LV2500(20)-UA(C) 10024
18954
55337
2844 16640 AUO
19LV2500(20)-UA(C) 5928
18954
55337
2844 16640
AUO
37LV3500-UA
22368 19478 55337
2844 16674 LGD
55LV3500(1,20)-NA(B,C) 46944 19478 55337
2840 24576 LGD
32LV3500(20)-UA(B) 18272
19478
55339
2844 16418 LGD
42LV3500(20)-UA(B) 26464
19478
55339
2844 16672 LGD
32LV3500(1,20)-NA(B,C) 18288 19478 55337
2840 16416 IPS-A
42LV3400-NA 26592 9226
53289
2840 16416
LGD
32LV3400-NA 18400 9226
53289
2332 16418
LGD
32LV2500-UA
18208 19478 55337
2844 16674 LGD
26LV2500(20)-UA(C) 14112 18954 55337
2844 16640 LGD
Click on the first or last page to see other 55LV5300 (CHASSIS:LA01U) service manuals if exist.