DOWNLOAD LG 55LM9600 (CHASSIS:LT23E) Service Manual ↓ Size: 6.24 MB | Pages: 62 in PDF or view online for FREE

Model
55LM9600 (CHASSIS:LT23E)
Pages
62
Size
6.24 MB
Type
PDF
Document
Service Manual
Brand
Device
TV / LCD
File
55lm9600-chassis-lt23e.pdf
Date

LG 55LM9600 (CHASSIS:LT23E) Service Manual ▷ View online

- 11 -
4.4. Input tool option.
Adjust tool option refer to the BOM.
▪ Tool Option Input : PCBA Check Process
▪ Area Option Input : Set Assembly Process
*** Tool Option table
MODEL
55LM9600
47LM9600
47LM8600
72LM9500
Tool Option1
33001
32999
32983
33148
Tool Option2
46421
46421
42325
50517
Tool Option3
21325
21325
21357
21325
Tool Option4
21039
21039
12845
21039
Tool Option5
23063
23063
23063
6677
Tool Option6
1321
1321
1321
1321
Tool Option7
63019
63019
62763
63019
After Input Tool Option and AC off
Before  PCBA  check,  you  have  to  change  the  Tool  option  and 
have to AC off/on (Plug out and in)
(If missing this process, set can operate abnormally)
4.4.1. Profile 
Must be changed the option value because being different with 
some setting value depend on module maker, inch and market
 
4.4.2. Equipment  
Adjustment remote control
4.4.3. Adjustment method     
The input methods are same as other chassis.(Use ADJ Key 
on the Adjust Remocon.)
(If not changed the option, the input menu can differ the model 
spec.)
Refer  to  Job  Expression  of  each  main  chassis  ass’y 
(EBTxxxxxxxx) for Option value  
Caution :  Don’t  Press  “IN-STOP”  key  after  completing  the 
function inspection.
4.5. EDID D/L method
Recommend that don’t connect HDMI and RGB(D-SUB) cable 
when downloading the EDID.
If not possible, recommend that connect the MSPG equipment.
There are two methods of downloading the edid data
It is a VESA regulation. A PC or a MNT will display an optimal 
resolution through information
Sharing without any necessity of user input. It is a realization 
of “Plug and Play”
4.5.1. 1st Method    
EDID datas are automatically downloaded when adjusting the 
Tool Options.
Automatically  downloaded  when  pushing  the  enter  key  after 
adjusting the tool option5.
It takes about 2seconds
4.5.2. 2nd Method
● Caution : Must be checked that the tool option is right or not. 
                    If tool option is wrong, hdmi edid data could not be 
downloaded well. 
1)  Press the ADJ key
2)   Move  to  the  10.  EDID  D/L  and  Press  the  right  direction 
key(►)
3)  Press the right direction key(►) at Start.
4)   After about a few seconds, appear “Waiting..” => “OK”, then 
compele.
4.5.3. RS-232C command Method
1) Command : AE 00 10
● Caution :  Don’t connect HDMI and RGB(D-SUB) cable when 
downloading the EDID.
                    If  the  cables  are  connected,  Downloading  of  edid 
could be failed
- 12 -
4.5.4. EDID data 
4.5.4.1. HDMI(FHD 3D_Deep color support)
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 01 16 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26
20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80
30 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C
40 45 00 A0 5A 00 00 00 1E 66 21 50 B0 51 00 1B 30
50 40 70 36 00 A0 5A 00 00 00 1E 00 00 00 FD 00 3A
60 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 43
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
02 03 37 F1 4E 10 9F 04 13 05 14 03 02 12 20 21
10 22 15 01 26 15 07 50 09 57 07 78 03 0C 00 10 00
20 B8 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16
30 10 28 10 E3 05 03 01 02 3A 80 18 71 38 2D 40 58
40 2C 45 00 A0 5A 00 00 00 1E 01 1D 80 18 71 1C 16
50 20 58 2C 25 00 A0 5A 00 00 00 9E 01 1D 00 72 51
60 D0 1E 20 6E 28 55 00 A0 5A 00 00 00 1E 00 00 00
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 11
(1) HDMI 1 Check sum : 0x43, 0X11 (CEA Block 0x1E :10)
(2) HDMI 2 Check sum : 0x43, 0X01 (CEA Block 0x1E :20)
(3) HDMI 3 Check sum : 0x43, 0XF1 (CEA Block 0x1E :30)
(4) HDMI 4 Check sum : 0x43, 0XE1 (CEA Block 0x1E :40)
4.5.4.2. RGB(Check sum : 5C)
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 01 16 01 03 68 A0 5A 78 0A EE 91 A3 54 4C 99 26
20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80
30 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C
40 45 00 A0 5A 00 00 00 1E 66 21 50 B0 51 00 1B 30
50 40 70 36 00 A0 5A 00 00 00 1E 00 00 00 FD 00 3A
60 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 00 5C
4.6. ADC Calibration : Comp 480i/Comp 1080p/RGB 
  If Adjust ADC  is  “OTP”,  It  doesn’t  need ADC  adjustment. 
(GP3-BCM)
4.6.2. Automatic ADC Calibration
4.6.2.1. Process
ADC adjustment is needed to find the optimum black level and 
gain  in Analog  to  Digital  device  and  to  compensate  RGB 
deviation
4.6.2.2. Equipment & Condition
1) Jig(RS-232C protocol)
2) Inner Pattern
    - Resolution : 1080P(inner pattern)
    - Resolution : 1024 * 768 RGB(Inner pattern)
    - Pattern : Horizontal 100% Color Bar Pattern
    - Pattern level : 0.7± 0.1 Vp-p
4.6.2.3. Adjustment Process
4.6.2.3.1. Adj protocol
Protocol
Command
Set ACK
Enter adj. mode
aa 00 00
a 00 OK00x
Source change
xb 00 40
xb 00 60 
b 00 OK40x (Adjust 480i Comp1 )
b 00 OK60x (Adjust 1024*768 RGB)
Begin adj.
ad 00 10
Return adj. result
OKx (Case of Success)
NGx (Case of Fail)
Read adj. data
(main)
ad 00 20 
(sub )
ad 00 21
(main)
000000000000000000000000007c007b006dx
(Sub)
000000070000000000000000007c00830077x
Confirm adj.
ad 00 99
NG 03 00x (Fail)
NG 03 01x (Fail)
NG 03 02x (Fail)
OK 03 03x (Success)
End adj.
aa 00 90
a 00 OK90x
4.6.2.3.2. Adj order
(1) aa 00 00 [Enter ADC adj. model]
(2) xb 00 40 [Change input source to Component(480i)]
(3) ad 00 10 [Adjust 480i Component1]
(4) xb 00 60 [Change input source to RGB(1024*768)]
(5) ad 00 10 [Adjust 1024*768 RGB]
(6) ad 00 90 [End adj]
(Ref) ADC adj RS232C Protocol_Ver1.0
- 13 -
4.7. Check SW Version 
4.7.1. Method
1) Push In-star key on Adjust remote-controller.
2) SW Version check(ex. 47LW9500-DA)
5. SET assembly adjustment method
5.1. Input Area-Option
(1) Profile :  Must  be  changed  the Area  option  value  because 
being  different  of  each  Country’s  Language  and 
signal Condition. 
(2) Equipment : adjustment remote control.
(3) Adjustment method
-  The input methods are same as other chassis.(Use IN-START 
Key on the Adjust Remocon.)
   Refer  to  Job  Expression  of  each  main  chassis  ass’y 
(EBTxxxxxxxx) for Option value
5.2. Adjustment of White Balance
●  In case of keeping module is in the circumstance of 0°C, it 
should  be  placed  in  the  circumstance  of  above  15°C  for  2 
hours 
●  In case  of keeping  module  is  in  the circumstance  of below 
-20°C, it should be placed in the circumstance of above 15°C 
for 3 hours.
▪ Purpose :  Adjust the color temperature to reduce the deviation 
of the module color temperature.
▪ Principle :  To adjust the white balance without the saturation, 
Fix the one of R/G/B gain to 192 (default data) and 
decrease the others.
▪ Adjustment mode : Three modes – Cool / Medium / Warm
 Required Equipment
▪ Remote controller for adjustment 
▪  Color Analyzer : CA100+ or CA-210 or same product (should 
be used in the calibrated ch by CS-1000)
- LCD TV : CH-9
- PDP TV : CH-10
- White LED TV : CH-14
- RGB LED(MNT) : CH-16
▪  Auto W/B adjustment instrument(only for Auto adjustment)
5.2.1. Adjustment of White Balance : 
          (For Automatic Adjustment)
Connecting  diagram  of  equipment  for  measuring  (For 
Automatic Adjustment)
1) Set TV in adj. mode using POWER ON key
2)  Zero  calibrate  probe  then  place  it  on  the  center  of  the 
Display
3) Connect Cable(RS-232C)
4) Select mode in adj. Program and begin adj.
5)  When  adj.  is  complete  (OK  Sing),  check  adj.  status  pre 
mode(Warm, Medium, Cool)
6) Remove probe and RS-232C cable to complete adj.
▪  W/B Adj.  must  begin  as  start  command  “wb  00  00”  ,  and 
finish as end command “wb 00 ff”, and Adj. offset if need
  Luminance  min  value  is  150cd  in  the  Cool/Medium/Warm 
mode( For LCD)
- 14 -
5.2.2. Adjustment of White Balance (for Manual adjustment)
▪  Color  analyzer(CA100+,  CA210)  should  be  used  in  the 
calibrated ch by CS-1000
▪  Operate the zero-calibration of the CA100+ or CA-210, then 
stick sensor to the module when adjusting.
▪  For  manual  adjustment,  it  is  also  possible  by  the  following 
sequence.
1)   Select white pattern of heat-run by pressing “POWER ON” 
key on remote control for adjustment then operate heat run 
longer than 15 minutes. 
    (If  not  executed  this  step,  the  condition  for  W/B  may  be 
different.)
2) Push “Exit” key.
3)  Change to the AV mode by remote control.
4)  Input external pattern (80% white pattern)
5)  Push the ADJ key => Enter “0000” (Password)
6)  Select “3. W/B ADJUST”
7)  Enter the W/B ADJUST Mode
8)   Stick the sensor to the center of the screen and select each 
items (Red/Green/Blue Gain and Offset) using ▲/▼(CH +/-) 
key on R/C..
9)  Adjust R/ G/ B Gain using ◄/►(VOL +/-) key on R/C.
10)  Adjust  three  modes  all  (Cool  /  Medium  /  Warm)  :  Fix  the 
one of R/G/B gain and change the others
11) When adjustment is completed,  Enter “COPY ALL” 
12) Exit adjustment mode using EXIT key on R/C.
 CASE
First adjust the coordinate far away from the target value(x, y).
(1) x, y >target
    i) Decrease the R, G. 
(2) x, y < target
    i) First decrease the B gain, 
    ii) Decrease the one of the others.
(3)  x >target ,  y< target
    i) First decrease B, so make y a little more than the target.
    ii) Adjust x value by decreasing the R
(4)  x < target ,  y >target
    i) First decrease B, so make x a little more than the target.
    ii) Adjust x value by decreasing the G
●  Standard color coordinate and temperature when using the 
CA100+ or CA210 equipment
Change reason :  When  vivid  mode,  more  detail  than  other 
company set.
●  In case of Edge LED module, the color coordinates is changing 
by aging, so you have to use the below table.
The Time Table of color coordinates by SET Aging Time
(1) Edge LED Models(47LM8600-DA)
GP3
Aging 
time
(Min)
Cool
Medium
Warm
x
y
x
y
x
y
269
273
285
293
313
329
1
0 ~ 2
293
305
309
323
330
348
2
3 ~ 5
292
303
308
321
330
347
3
6 ~ 9
291
302
307
320
329
346
4
10 ~19
288
298
304
316
326
342
5
20 ~ 35
286
295
302
313
324
339
6
36 ~ 49
285
293
301
311
322
337
7
50 ~ 79
283
291
299
309
321
335
8
80 ~ 149
282
289
298
308
320
334
9
Over 150
281
287
298
306
319
332
 
(2) ALEF (47LM9600-DA)
GP3
Aging 
time
(Min)
Cool
Medium
Warm
x
y
x
y
x
y
269
273
285
293
313
329
1
0 ~ 2
283
293
299
313
320
339
2
3 ~ 5
282
291
298
311
319
337
3
6 ~ 9
281
290
297
310
318
336
4
10 ~19
279
289
295
309
316
335
5
20 ~ 35
277
284
293
304
314
330
6
36 ~ 49
274
279
290
299
311
325
7
50 ~ 79
271
277
287
297
308
323
8
80 ~ 119
270
274
286
294
307
320
9
Over 120
269
273
285
293
306
319
(3) ALEF (55LM9600-DA)
GP3
Aging 
time
(Min)
Cool
Medium
Warm
x
y
x
y
x
y
269
273
285
293
313
329
1
20
282
298
298
318
319
344
2
21 ~ 25
280
296
296
316
317
342
3
26 ~ 30
279
294
295
314
316
340
4
31 ~ 35
277
292
293
312
314
338
5
36 ~ 40
276
290
292
310
313
336
6
41 ~ 50
275
288
291
308
312
334
7
51 ~ 80
272
284
288
304
309
330
8
81 ~ 119
271
282
287
302
308
328
9
Over 120
270
281
286
301
307
327
Color coordinate 
Mode  
X
 
Temp
 △uv
Cool 
0.269±0.002
 
0.273±0.002  13000K 
0.0000  
Medium  0.285±0.002
 
0.293±0.002  9,300 K  0.000 
Warm 
0.313±0.002
 
0.329±0.002  6,500K  0.003 
Page of 62
Display

Click on the first or last page to see other 55LM9600 (CHASSIS:LT23E) service manuals if exist.