DOWNLOAD LG 55LM660S / 55LM660T (CHASSIS:LD22E) Service Manual ↓ Size: 10.77 MB | Pages: 119 in PDF or view online for FREE

- 13 -

*  ADC  adjustment  is  not  needed  because  of  OTP(Auto ADC 

adjustment)

It is a VESA regulation. A PC or a MNT will display an optimal 

resolution  through  information  sharing  without  any  necessity 

of user input. It is a realization of "Plug and Play".

-  Since  embedded  EDID  data  is  used,  EDID  download  JIG, 

HDMI cable and D-sub cable are not need.

- Adjustment remote control

(1)  Press  "ADJ"  key  on  the Adjustment  remote  control  then 

select "10.EDID D/L", By pressing "Enter" key, enter EDID 

D/L menu.

(2)  Select  "Start"  button  by  pressing  "Enter"  key,  HDMI1/ 

HDMI2/ HDMI3/ HDMI4/ RGB are writing and display OK 

or NG.

(1) 3D EDID DATA

▪ Reference

- HDMI1 ~ HDMI4 / RGB 

-  In the data of EDID, bellows may be different by S/W or 

Input mode. 

ⓐ

. Product ID

ⓑ

. Serial No: Controlled on production line.

ⓒ

. Month, Year: Controlled on production line:

ex) Week : '01' -> '01'

Year : '2012' -> '16' fix

ⓓ

. Model Name(Hex): LGTV

ⓔ

. Checksum: Changeable by total EDID data.

ⓕ

. Vendor Specific(HDMI)

1) Deep color (module 10bit)

2) None deep color (module 8bit)

ⓖ

 Colorimetry Data Block(HDMI)

- The Model supporting XvYcc(LM7600) 

For Analog

For HDMI EDID

D-sub to D-sub

DVI-D to HDMI or HDMI to HDMI

HEX

EDID Table

DDC Function

0001

01 00

Analog/Digital

Chassis

MODEL NAME(HEX)

LD22E

00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 

INPUT

MODEL NAME(HEX)

HDMI1 78 03 0C 00 10 00 B8 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10
HDMI2 78 03 0C 00 20 00 B8 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10
HDMI3 78 03 0C 00 30 00 B8 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10
HDMI4 78 03 0C 00 40 00 B8 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

INPUT

MODEL NAME(HEX)

HDMI1 78 03 0C 00 10 00 80 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10
HDMI2 78 03 0C 00 20 00 80 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10
HDMI3 78 03 0C 00 30 00 80 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10
HDMI4 78 03 0C 00 40 00 80 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

INPUT

MODEL NAME(HEX)

HDMI1

E3 05 03 01

HDMI2

E3 05 03 01

HDMI3

E3 05 03 01

HDMI4

E3 05 03 01

ⓔ

1

ⓔ

2

10 bit/ 

Xvycc

ⓔ

2

8 bit/ 

Xvycc

ⓔ

2

10 bit/

none XvYcc

ⓔ

2

8 bit/

none XvYcc

ⓔ

3

HDMI1

43

11

49

15

4D

X

HDMI2

43

01

39

05

3D

X

HDMI3

43

F1

29

F5

2D

X

HDMI4

43

E1

19

E5

1D

X

RGB

X

X

X

X

X

5C

- 14 -

▪ W/B adj. Objective & How-it-works

(1) Objective: To reduce each Panel's W/B deviation

(2)  How-it-works : When R/G/B gain in the OSD is at 192, it 

means the panel is at its Full Dynamic Range. In order to 

prevent saturation of Full Dynamic range and data, one 

of R/G/B is fixed at 192, and the other two is lowered to 

find the desired value. 

(3) Adjustment condition : normal temperature

1) Surrounding Temperature : 25 °C ± 5 °C

2) Warm-up time: About 5 Min

3) Surrounding Humidity : 20 % ~ 80 %

(1) Color Analyzer: CA-210 (LED Module : CH 14)

(2)  Adjustment Computer(During auto adj., RS-232C protocol 

is needed)

(3) Adjustment Remote control

(4)  Video Signal Generator MSPG-925F 720p/204-Gray

(Model: 217, Pattern: 49)

-> Only when internal pattern is not available

▪ Color Analyzer Matrix should be calibrated using CS-100.

<Command Format>

- LEN: Number of Data Byte to be sent

- CMD: Command

- VAL: FOS Data value

- CS: Checksum of sent data

- A: Acknowledge

Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX]

▪ RS-232C Command used during auto-adjustment.

Ex)  wb 00 00   ->  Begin white balance auto-adj.

 

wb 00 10   ->  Gain adj.

 

ja 00 ff   ->  Adj. data

 

jb 00 c0

 

...

 

...

 

wb 00 1f   → Gain adj. completed

    *(wb 00 20(Start), wb 00 2f(end)) → Off-set adj.

 

wb 00 ff   → End white balance auto-adj.

▪ Adj. Map

(1) Auto adj. method

1) Set TV in adj. mode using P-Only key.

2)  Zero  calibrate  probe  then  place  it  on  the  center  of  the 

Display.

3) Connect Cable.(RS-232C to USB)

4) Select mode in adj. Program and begin adj.

5)  When adj. is complete (OK Sign), check adj. status pre 

mode. (Warm, Medium, Cool)

6) Remove probe and RS-232C cable to complete adj.

▪  W/B Adj. must begin as start command “wb 00 00” , and 

finish as end command “wb 00 ff”, and Adj. offset if need.

(2) Manual adjustment. method

1) Set TV in Adj. mode using P-Only key.

2)  Zero Calibrate the probe of Color Analyzer, then place it 

on the center of LCD module within 10 cm of the surface.

3)  Press ADJ key → EZ adjust using adj. R/C → 7. White-

Balance then press the cursor to the right(key ►).

(When right key(►) is pressed 216 Gray internal pattern 

will be displayed)

4)  One of R Gain / G Gain / B Gain should be fixed at 192, 

and the rest will be lowered to meet the desired value.

5)  Adjustment  is  performed  in  COOL,  MEDIUM,  WARM  3 

modes of color temperature.

 ▪  If  internal  pattern  is  not  available,  use  RF  input.  In  EZ 

Adj.  menu  7.White  Balance,  you  can  select  one  of  2 

Test-pattern: ON, OFF. Default is inner(ON). By selecting 

OFF, you can adjust using RF signal in 216 Gray pattern.

START 6E A 50 A LEN A 03 A CMD

A

00

A VAL A

CS STOP

Color Analyzer

 

Computer 

Pattern Generator

 

RS-232C 

RS-232C 

RS-232C 

Probe

Signal Source

* If TV internal pattern is used, not needed

RS-232C COMMAND

[CMD 

ID 

DATA]

Explantion

wb

00

00

Begin White Balance adjustment

wb

00

10

Gain adjustment(internal white pattern)

wb

00

1f

Gain adjustment completed

wb

00

20

Offset adjustment(internal white pattern)

wb

00

2f

Offset adjustment completed

wb

00

ff

End White Balance adjustment

(internal pattern disappears )

Adj. item

Command

(lower caseASCII)

Data Range

(Hex.)

Default

(Decimal)

CMD1

CMD2

MIN

MAX

Cool

R Gain

j

g

00

C0

G Gain

j

h

00

C0

B Gain

j

i

00

C0

R Cut
G Cut
B Cut

Medium

R Gain

j

a

00

C0

G Gain

j

b

00

C0

B Gain

j

c

00

C0

R Cut
G Cut
B Cut

Warm

R Gain

j

d

00

C0

G Gain

j

e

00

C0

B Gain

j

f

00

C0

R Cut
G Cut

- 15 -

▪ Adjustment condition and cautionary items

1) Lighting condition in surrounding area

Surrounding  lighting  should  be  lower  10  lux.  Try  to 

isolate adj. area into dark surrounding.

2) Probe location

:  Color Analyzer(CA-210) probe should be within 10 cm 

and perpendicular of the module surface.(80° ~ 100°)

3) Aging time

-  After Aging Start, Keep the Power ON status during 5 

Minutes.

-  In  case  of  LCD,  Back-light  on  should  be  checked 

using no signal or Full-white pattern.

▪ Luminance : 204 Gray

▪  Standard  color  coordinate  and  temperature  using  CS-1000 

(over 26 inch)

▪ Standard color coordinate and temperature using CA-210(CH 14)

-  EDGE  LED  module  change  color  coordinate  because  of 

aging time.

-  Apply  under  the  color  coordinate  table,  for  compensated 

aging time.

- ALEF(LM76 series)

(1) Turn on TV.

(2) Press EYE key of Adjustment remote control.

(3)  Cover the Eye Q II sensor on the front of the using your 

hand and wait for 6 seconds.

(4)  Confirm  that  R/G/B  value  is  lower  than  10  of  the  "Raw 

Data (Sensor data, Back light)". If after 6 seconds, R/G/B 

value is not lower than 10, replace Eye Q II sensor.

(5)  Remove your hand from the Eye Q II sensor and wait for 6 

seconds.

(6)  Confirm  that  "ok"  pop  up.  If  change  is  not  seen,  replace 

Eye Q II sensor.

Step 1) Turn on TV.

Step 2) Press “TILT” key on the Adj. R/C.

Step 3)  At  the  Local  Dimming  mode,  module  Edge  Backlight 

moving right to left Back light of IOP module moving.

Step 4) Confirm the Local Dimming mode.

Step 5) Press "exit" key.

(1)  Equipment  :  RF  Remote  control  for  test,  IR-KEY-Code 

Remote control for test

(2)  You  must  confirm  the  battery  power  of  RF-Remote  control 

before test(recommend that change the battery per every lot)

(3) Sequence (test)

1)  if  you  select  the  "Start(Wheel)"  key  on  the Adjustment 

remote control, you can pairing with the TV SET.

2)  You can check the cursor on the TV Screen, when select 

the "Wheel" key on the Adjustment remote control.

3)  You must remove the pairing with the TV Set by select 

"Mute" key on the Adjustment remote control

Mode

Coordinate

Temp

∆uv

x

y

Cool

0.269

0.273

13000 K

0.0000 

Medium

0.285

0.293

9300 K

0.0000 

Warm

0.313

0.329

6500 K

0.0000 

Mode

Coordinate

Temp

∆uv

x

y

Cool

0.269 ± 0.002

0.273 ± 0.002 13000 K 0.0000 

Medium 0.285 ± 0.002

0.293 ± 0.002

9300 K 0.0000 

Warm

0.313 ± 0.002

0.329 ± 0.002

6500 K 0.0000 

GP4

Aging 

time

(Min)

Cool

Medium

Warm

X

y

x

y

x

y

269

273

285

293

313

329

1

0-2

283

293

299

313

320

339

2

3-5

282

291

298

311

319

337

3

6-9

281

290

297

310

318

336

4

10-19

279

289

295

309

316

335

5

20-35

277

284

293

304

314

330

6

36-49

274

279

290

299

311

325

7

50-79

271

277

287

297

308

323

8

80-119

270

274

286

294

307

320

9

Over 120

269

273

285

293

306

319

- 16 -

(Pattern Generator MSHG-600, MSPG-6100[Support HDMI1.4])

* HDMI mode NO. 872 , pattern No.83

(1)  Please input 3D test pattern like below.

(2) When 3D OSD appear automatically, then select OK key.

(3) Don't wear a 3D Glasses, check the picture like below.

Step 1) Turn on TV

Step 2) Select Network Connection option in Network Menu.

Step 3) Select Start Connection button in Network Connection.

Step 4)  If the system finds any AP like blow PIC, it is working 

well.

(only for DVB-S/S2 model)

▪ Test method

(1) Set TV in Adj. mode using POWER ON.

(2) Connect cable between satellite ANT and test JIG.

(3)  Press Yellow key(ETC+SWAP) in Adj Remote control to 

make LNB on.

(4) Check LED light ‘ON’ at 18 V menu.

(5) Check LED light ‘ON’ at 22 KHz tone menu.

(6)  Press Blue key(ETC+PIP INPUT) in Adj Remote control 

to make LNB off.

(7) Check LED light ‘OFF’ at 18 V menu.

(8) Check LED light ‘OFF’ at 22 KHz tone menu.

▪ Test result

(1)  After  press  LNB  On  key,  ‘18  V  LED’  and  ‘22  KHz  tone 

LED’ should be ON. 

(2)  After press LNB OFF key, ‘18 V LED’ and ‘22 KHz tone 

LED’ should be OFF. 

-  Option selection is only done for models in Non-EU 

(1)  Press ADJ key on the Adj. R/C, then select Country Group 

Meun

(2)  Depending on destination, select Country Group Code 04 

or  Country  Group  EU  then  on  the  lower  Country  option, 

select  US,  CA,  MX.  Selection  is  done  using  +,  -  or  ►◄ 

key.

▪  Method : Press "ADJ" key on the Adjustment remote control, 

then select Tool option.

▪  After final inspection, press "IN-STOP" key of the Adjustment 

remote control and check that the unit goes to Stand-by mode.