DOWNLOAD LG 50PS6500-ZA (CHASSIS:PD91A) Service Manual ↓ Size: 9.37 MB | Pages: 44 in PDF or view online for FREE

- 5 -

V

No

Item

Specification

Remarks

1

Market

Albania, Austria, Belgium, Bosnia, Bulgaria,

36 Country 

Coratia, Czech, Denmark, Estonia, Finland, 

France, Germany, Greece, Hungary, Ireland, 

Italy, Kazakhstan, Latvia, Lithuania, 

Luxembourg, Morocco, Netherlands, Norway, 

Poland, Portugal, Romania, Russia, Serbia, 

Slovenia, Spain, Sweden, Slovakia, 

Switzerland, Turkey, Ukraine, UK

2

Broadcasting system

1)  PAL/SECAM BG

EU (PAL Market)

2)  PAL/SECAM DK

3)  PAL 

Ⅰ/Ⅱ

4)  SECAM L/L’

5)  DVB T 

6)  DVB C

DVB C (only Sweden, Pinland)

3

Receiving system

Analog : Upper Heterodyne

Digital : COFDM, QAM

4

Scart Jack (2EA)

PAL, SECAM

Scart 1 Jack is Full scart and support 

RF-OUT(Analoge)

Scart 2 jack is Half scart and support 

MNT-OUT.

5

Video Input (1EA)

PAL, SECAM, NTSC

Side AV

6

S-Video Input (1EA)

PAL, SECAM, NTSC

Side AV

7

Component Input (1EA)

Y/Cb/Cr, Y/ Pb/Pr

8

RGB Input

RGB-PC

Analog (D-Sub 15Pin)

9

HDMI Input (4EA)

HDMI-PC

HDMI1/DVI, HDMI2, HDMI3, HDMI4

HDMI-DTV

Upper 70 tool, But under 60 tool HDMI 3EA.

10

Audio Input (3 EA)

RGB/DVI Audio, Component, AV

L/R Input

11

SPDIF Out(1 EA)

SPDIF Out

12

USB

For SVC, S/W Download, X-Studio, DivX

13

Bluetooth

Bluetooth Phone(JPEG, MP3), 

Profile : A2DP, BIP, FTP, GAVDP, HSP, OPP

Bluetooth Headset(mono, stereo)

- 6 -

This spec. sheet is applied to all of the PD91A chassis.

1.  The  module  keeping  condition:  The  normal  temperature

condition(more than 15°C)
--> Immediately the line supply.

2. The module keeping condition: 0°C

-->  The module must be kept for more than 2 hours at the

normal temperature.

3. The module keeping condition: -20°C

-->  The module must be kept for more than 3 hours at the

normal temperature.

4. The case of Gu-mi factory at the winter season.

-->    The  module  must  be  kept  for  more  than  5  minutes  at

the heating zone(40°C~45°C).

(1)  The  adjustment  is  according  to  the  order  which  is

designated  and  which  must  be  followed,  according  to  the
plan which can be changed only on agreeing.

(2) If there is no specific designation, the adjustment must be

performed  in  the  circumstance  of  25±5°C  of  temperature
and 65±10% of relative humidity.

(3)  The  input  voltage  of  the  set  must  keep  100~240V,

50/60Hz.

(4) Input signal Unit: Product Specification Standard.
(5) The set must be operated for about 5 minutes prior to the

adjustment.

O

After  turning  on  RGB  Full  Window  pattern  in  HEAT-RUN

Mode, the receiver must be operated.

O

Enter into HEAT-RUN MODE 

1) Press the ‘POWER ON’ button on R/C for adjustment.
2) Press the ‘ADJ’ button on R/C and enter EZ ADJUST

Select “7. Test Pattern” by using 

D

/

E

(CH +/-) and press

ENTER(

V

)

Select  “White”  by  using 

F

/

G

(VOL  +/-)  and  press

ENTER(

V

)

- Set heat run should be activated without a signal generator. 
- Single color patterns (RED / BLUE / GREEN) of HEAT RUN

MODE are used to check a plasma panel. 

-  Caution:  If  you  turn  on  a  still  screen  more  than  20  minutes

(Especially  digital  pattern,  cross  hatch  pattern),  an  after
image may be made in the black level part of the screen.

[Caution] 
- Use ‘power on’ button of a service R/C to power on TV set.
-  Do  not  connect  any  external  input  cable  if  there  is  no  any

specifics.

Caution:  S/W  version  of  USB  file  (xxx.epk)  must  be  bigger  than

one which is downloaded previously.

(1) Insert the USB stick to the USB socket 
(2)  A  downloaded  file  in  USB  stick  will  be  detected

automatically.

(3)  If  S/W  version  of  USB  file  (xxx.epk)  is  bigger  than  one

which  is  downloaded  previously,  the  message,  “Copying
files from memory”, will appear. 

(4)  If  an  update  procedure  was  completed,  TV  set  will  be

turned off and on automatically.

(5) If TV set is turned on, check an updated version.

* If a downloaded version is more bigger than one of which

TV  set  had,  TV  set  can  lost  channel  data.  In  this  case,
you have to scan channels again. 

(1) Push “IN-START” button on a service R/C.
(2) Select “Tool Option 1” and Push “OK” button.
(3) Put the number of a below table in order of a suffix of the

“Tool Option(X)”. 
(Each model has a different number.)

Model           Tool Option1  Tool Option2  Tool Option3 Tool Option4

50PS7000-ZA

37184

3126

55792

3328

50PS8000-ZA

37248

3126

55792

11520

60PS7000-ZA

49472

3126

55792

3328

60PS8000-ZA

49536

3126

55792

11520

42PQ3500-ZB

25088

2102

51692

3328

42PQ6500-ZA

25152

2102

51692

3328

50PQ3500-ZB

37376

2102

51692

3328

50PS6500-ZC

37504

2102

51692

3328

(1) Input the component (480i/Horizontal Color Bar) signal to a

TV set.
1) Input Signal Timing : Component 480i 

(Other  external  connection  is  unnecessary  except  the
component before executing ADC calibration.)

2) Input Signal Pattern

@ MODEL: 209 in Pattern Generator(480i Mode)
@  PATTERN  :  65  in  Pattern  Generator(MSPG-925

SERISE) 

(2) Push “ADJ” button on a service R/C.
(3) Enter internal ADC mode by selecting ‘5. ADC Calibration’.
(4)  If  you  select  ‘Start’  on  a  dialog  box  of  the  screen,  ADC

calibration will be begun.

Caution:  Don’t  connect  any  external  input  cable  except  the

component  input(480i/Horizontal_Color_Bar)  to  adjust
ADC calibration

O

Auto ADC Calibration Map(RS-232C)

# Adjust Sequence

- aa 00 00  [Enter Adjust Mode]
- xb 00 40  [Component1 Input (480i)]
- ad 00 10  [Adjust 480i Comp1]
- xb 00 60  [RGB Input (1024*768)]
- ad 00 10  [Adjust 1024*768 RGB]
- aa 00 90  End Adjust mode

(1) Push “ADJ” button on a service R/C.
(2)  Enter  EDID  auto  download  mode  by  selecting  ‘8.  EDID

D/L’.

(3)  If  you  select  ‘Start’  on  a  dialog  box  of  the  screen,  EDID

download will be begun automatically.

(4) Press ‘EXIT’ button on a service R/C.
(5) EDID Data

1) HDMI (FHD M

256 bytes)

2) RGB (FHD M

128 bytes)

O

EDID Data detailing (

ⓐ, ⓑ, ⓒ, ⓓ, ⓔ, ⓕ)

- 7 -

<Horizontal Color Bar pattern>

NO

Item

CMD1

A

A

0

0

0

1

D

A

CMD2 Data0

Enter  

Adjust MODE

Adjust 

‘Mode In’

When transfer the ‘Made

In’, Carry the command.

Automatically adjustment

(The use of a internal

pattern)

ADC

Adjust

ADC Adjust

00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F

00 00 FF FF FF FF FF FF 00 1E 6D

ⓐ

ⓑ

10

ⓒ

01 03 80 46 27 78 EA D9 B0 A3 57 49 9C 25

20 11 49 4B A1 08 00 31 40 45 40 61 40 81 80 90 40

30 D1 C0 01 01 01 01 1A 36 80 A0 70 38 1F 40 30 20

40 35 00 E8 26 32 00 00 1A 1B 21 50 A0 51 00 1E 30

50 48 88 35 00 BC 86 21 00 00 1C 00 00 00 FD 00 38

60 3E 1C 53 12 00 0A 20 20 20 20 20 20            

ⓓ

70

ⓓ

01

ⓔ

00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F

00 00 FF FF FF FF FF FF 00 1E 6D

ⓐ

ⓑ

10

ⓒ

01 03 01 46 27 78 EA D9 B0 A3 57 49 9C 25

20 11 49 4B A1 08 00 31 40 45 40 61 40 81 80 90 40

30 D1 C0 01 01 01 01 1A 36 80 A0 70 38 1F 40 30 20

40 35 00 E8 26 32 00 00 1A 1B 21 50 A0 51 00 1E 30

50 48 88 35 00 BC 86 21 00 00 1C 00 00 00 FD 00 38

60 3E 1C 53 12 00 0A 20 20 20 20 20 20            

ⓓ

70

ⓓ

00

ⓔ

00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F

00 02 03 29 F1 51 81 02 03 06 07 15 16 11 12 13 04

10 14 05 20 22 1F 10 26 15 07 50 09 7F 07 67 03 0C

20 00

ⓕ 00 B8 2D E3 05 03 01 01 1D 00 80 51 D0 1C

30 20 40 80 35 00 BC 88 21 00 00 1E 4E 1F 00 80 51

40 00 1E 30 40 80 37 00 BC 88 21 00 00 18 02 3A 80

50 18 71 38 2D 40 58 2C 45 00 06 44 21 00 00 1E 01

60 1D 80 18 71 1C 16 20 58 2C 25 00 C4 8E 21 00 00

70 9E 00 00 00 00 00 00 00 00 00 00 00 00 00 00

ⓔ

ⓐ Product ID 

ⓑ Serial No

=> Controlled on production line

ⓒ Month, Year

=> Controlled on production line:  

ⓓ Model Name

ⓔ Checksum

=> Changeable by total EDID data

ⓕ HDMI Port No.

O

Auto EDID Download Map(RS-232C)

You must adjust DTV 29 Channel and insert PCMCIA CARD
to socket.
- If PCMCIA CARD works normally, video signals will appear

on screen.
But  it  works  abnormally,  “No  CA  module”  will  appear  on
screen.

[ Caution: Set up “RF mode” before launching products.

Caution: Both Vs and Va voltage adjustment are necessary.

50PS7000-ZA, 60PS7000-ZA, 50PS8000-ZA, 60PS8000-ZA

(1) Connect positive(+) terminal of DMM to Vs/Va pin, connect

negative(-) terminal to GND.

(2)  Turning  ‘Vs/Va  Adjust’  and  adjust  Vs/Va  voltages  to  a

value  which  is  written  on  a  right/top  label  of  a  module.
(deviation ; ±0.5V)

[Caution]

- Each Power Supply Unit PCB assembly must be checked by

check JIG set. (Because power PCB Ass’y damages to PDP
Module, especially be careful)

- Set up “RF mode(noise)” before a voltage adjustment.
- Test equipment: DMM 1EA

Caution:  Press  the  POWER  ON  KEY  on  R/C  before  W/B
adjustment.

O

Test Equipment

Color Analyzer (CS-1000, CA-100+(CH.10), CA-210(CH.10))

O

Please  adjust  CA-100+  /  CA-210  by  CS-1000  before

measuring
You  should  use  Channel  10  which  is  Matrix  compensated
(White, Red, Green, Blue revised) by CS-1000 and adjust

in accordance with White balance adjustment coordinate.

°°°°

- 8 -

NO

Item

CMD1

A

A

0

0

10

00

E

A

CMD2 Data0

Enter  

download

MODE

Download

‘Mode In’

When transfer the ‘Made

In’, Carry the command.

Automatically download

(The use of a internal

Data)

Download

EDID data and

Model option

download

6500K

Warm

9300K

Medium

11000K

Cool

PLASMA

CSM

MODEL

EDID MODEL

PRODUCT_ID

FUNCTION

42PQ60D-GA

LG TV

0001(0x01, 0x00)

Digital

42PQ60D-GA

LG TV

0001(0x01, 0x00)

Analog

50PQ60D-GA

LG TV

0001(0x01, 0x00)

Digital

50PQ60D-GA

LG TV

0001(0x01, 0x00)

Analog

50PS80FD-GA

LG TV

0001(0x01, 0x00)

Digital

50PS80FD-GA

LG TV

0001(0x01, 0x00)

Analog