LG 50PJ560R-TA (CHASSIS:PP01C) Service Manual ▷ View online
4. PCB Assembly Adjustment Method
4-1. Option Adjustment Following BOM
Tool Option
Area Option
Option 1
Option 2
Option 3(Available for EU & Non EU model)
Area Option
Option 1
Option 2
Option 3(Available for EU & Non EU model)
* Profile: Must be changed the option value because being
different with some setting value depend on module,
inch and market
inch and market
* Equipment : Adjustment Remote Controller
(1) Push the IN-START key in the Adjust R/C.
(2) Enter Password number. The value of Password is “0 0 0
(2) Enter Password number. The value of Password is “0 0 0
0”.
(3) Input the Option Number that was specified in the BOM,
into the Shipping area.
(4) Select “Tool Option” by using
D
/
E
(CH+/-) key, and press
the number key(0~9) consecutively
ex) If the value of Tool Option1 is 4, input the data using
number key “4” (Fig. 3)
(5) if it is EU model ( such as 42/50PJ**R-ZA ), select “Area
option” by using
D
/
E
(CH+/-) key , and press the number
key(0~9) consecutively.
ex) If the value of Area Option is 40, input the data using
number key “40” (Fig. 3)
Caution
- Don’t Push “IN-STOP” key after PCB assembly
adjustment.
* PP01A/B/C Tool option
(6) EDID D/L Method
After software D/L or PCBA manufacturing, you can
download EDID Data.
When you adjust Tool Option, H6 Model EDID download
process is executed automatically
download EDID Data.
When you adjust Tool Option, H6 Model EDID download
process is executed automatically
* If the model don’t have HDMI 3, HDMI 3 will be disappeared
at OSD Window.
Caution
- When you adjust tool option, don’t connect HDMI or D-
sub cable.
- If you connect some cable, EDID D/L process will be
failed.
(7) Adjustment method
Before PCBA check, have to change the Tool option and
Area option
Area option
[ About PDP
After done all adjustments, Press IN-START button and
compare Tool option and Area option value with its BOM, if
it is correctly same then Change “RF mode” and then
unplug the AC cable.
compare Tool option and Area option value with its BOM, if
it is correctly same then Change “RF mode” and then
unplug the AC cable.
If it is not same, then correct it same with BOM and unplug
AC cable.
AC cable.
For correct it to the model’s module from factory JIG
model.
model.
[ Don’t push The IN-STOP KEY after completing the function
inspection.
- 9 -
( Fig. 3)
Model
Tool option
50PJ250R-TA
16
42PJ250R-ZA
23
- 10 -
5. EDID(The Extended Display
Identification Data)
Caution
- Never Use the cable( HDMI or D-sub cable) for EDID
Writing.
- Automatically PP01A/B/C Model EDID download process
is executed when you adjust Tool Option.
< Jack Layout>
<Tool Option Item>
<CSA AREA>
<NON-EU AREA>
Inch
Tool
SIDE AV
0/1
HDMI
0/1/2/3
Side HDMI
0/1
COMP2
0/1
RGB
0/1
RS232C
0/1
Local Key
0 (7KEY) / 1 (8KEY)
LED TYPE
0 (RED) / 1 (RED/White) / 2 (Reserve)
USB TYPE
0 (NONE) / 1 (PHOTO, MUSIC)
/ 2 (PHOTO, MUSIC, DivX)
- 11 -
<EAST EU / CIS AREA>
5-1. EDID Data
O
WXGA EDID DATA ( 50inch)
<Analog(RGB) : 128bytes>
<HDMI 1 : 256bytes>
<HDMI 2 : 256bytes>
<HDMI 3 : 256bytes> SIDE HDMI(HDMI 3)
NO
Item
Condition
Hex Data
1
Manufacturer ID
GSM
1E6D
2
Version
Digital : 1
01
3
Revision
Digital : 3
03
- 12 -
6. HDCP(High-Bandwidth Digital
Contents Protection) Download
HDCP download process is deleted in PP01A/B/C Chassis
In PP01A/B/C Chassis, it is usi g the EEPROM masking
HDCP Key
In PP01A/B/C Chassis, it is usi g the EEPROM masking
HDCP Key
7. Manual ADC Adjustment
(Component 1, RGB)
Caution
- Do not connect external input cable
- Adjustment result is applied to SET On/Off later.
- Adjustment result is applied to SET On/Off later.
* Adjustment is done using internal ADC, so input signal is not
necessary.
7-1. COMPONENT input ADC (SD / HD),
RGB input ADC
(1) Press ADJ key on R/C for adjustment. Need not convert
input mode.
(2) Enter Password number. The value of Password is “0 0 0
0”.
(3) Select “0. ADC calibration” by using
D
/
E
(CH +/-) and press
ENTER(
V
).
(4) Start ADC adjustment by using
F
/
G
(VOL +/-) or press
ENTER(
V
).
(5) Both component and RGB ADC adjustment are executed
automatically
When ADC adjustment is finished, this OSD appear.
Notice : After All mode check, set the Speaker Volume “0”.
Caution : Don’t Press the Power Key on Remote Controller.
Just AC Power Off. ( Not DC off )
Notice : From this sentence, All working is mass production.
8. POWER PCB Assy Voltage
Adjustment
(Vs voltage Adjustment)
(Vs voltage Adjustment)
8-1. Test Equipment:
D.M.M 1EA
8-2. Connection Diagram for Measuring
Refer to (Fig. 4)
8-3. Adjustment Method
(1) Vs Adjustment
1) Connect + terminal of D. M..M. to Vs pin of P811,
connect -terminal to GND pin of P811.
2) After turning VR901, voltage of D.M.M adjustment as
same as Vs voltage which on label of panel right/top
( deviation ; ±0.5V)
(2) Va Adjustment
1) Connect + terminal of D. M..M. to Va pin of P811,
connect -terminal to GND pin of P811.
2) After turning VR502, voltage of D.M.M adjustment as
same as Va voltage which on label of panel right/top
( deviation ; ±0.5V)
RF input
NO SIGNAL or White noise
AV / Component / RGB input
NO SIGNAL
(Fig. 4)
Click on the first or last page to see other 50PJ560R-TA (CHASSIS:PP01C) service manuals if exist.