DOWNLOAD LG 50PG79ED-AF (CHASSIS:PA84D) Service Manual ↓ Size: 33.53 MB | Pages: 41 in PDF or view online for FREE

- 4 -

NOTE : Specifications and others are subject to change without notice for improvement.

V

This spec is applied to the 

PLASMA TV used PA84D Chassis.

V 

Each part is tested as below without special appointment.
1) Temperature : 25±5°C (77±9°F), CST : 40±5
2) Relative Humidity: 65±10%
3) Power Voltage: Standard Input voltage (100-240V~, 50/60Hz)

* Standard Voltage of each product is marked by models.

4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with SBOM.
5) The receiver must be operated for about 20 minutes prior to the adjustment.

V

1) Performance : LGE TV test method followed.
2) Demanded other specification 

Safety : CB specification
EMC

: CISPR 13 specification

Chassis

PA84D

60PG30UD-AA

42/50PG60UD-AA

42/50PG20D-AA

50/60PG30FD-AA

50/60PG70FD-AB

Australia

LG

Model Name

Market

Brand

Remark

60PG30UD-AA

42/50PG60UD-AA

42/50PG20D-AA

50/60PG30FD-AA

50/60PG70FD-AB

Safety : IEC/EN60065

EMI

: CISPR 13 Class B

Australia

Model

Appliance

Market

Remark

V

- 5 -

 

 

 

- 6 -

 

 

 

V

- 7 -

This spec. sheet is applied to all of the PA81A, PA81C
chassis manufactured at LG TV Plant all over the world.

(1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolation
transformer will help protect test instrument.

(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of

25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation.

(4) The input voltage of the receiver must keep 100~240V,

50/60Hz.

(5) The receiver must be operated for about 15 minutes prior

to the adjustment.

O

After RGB Full White in HEAT-RUN Mode, the receiver

must be operated prior to the adjustment.

O

Enter into HEAT-RUN MODE 

1) Press the POWER ON KEY on R/C for adjustment.
2) Press the ADJ KEY on R/C and enter EZ ADJUST

- Select “3. Test Pattern” by using 

D

/

E

(CH +/-) and

press ENTER(

V

)

- Select “White” by using 

F

/

G

(VOL +/-) and press

ENTER(

V

)

* Set is activated HEAT-RUN without signal generator in

this mode. 

* Single color pattern ( RED / BLUE / GREEN ) of HEAT

RUN MODE uses to check panel. 

* Caution : If you turn on a still screen more than 20

minutes (Especially digital pattern, cross hatch pattern),
an after image may be occur in the black level part of
the screen.

Caution: Using ‘power on’ button of the control R/C , power
on TV.
All adjustment process is executed one time through RS-
232C.
Do not connect external input cable.
Power off TV After adjustment method, not using ‘in-stop’
button of control R/C

Caution: Using ‘power on’ button of the control R/C, power on
TV.
USB file (EPK) version must be bigger than downloaded
version of main B/D.

(1) Insert the USB memory stick to the PCB ASSEMBLY.
(2) Using ‘power on’ button of the control R/C, power on TV.
(3) S/W download process is executed automatically.

(1) All adjustment process is executed one time through RS-

232C.

(2) Command send 

(

ADC Calibration 

(

Model name

download 

(

EDID download.

1

2

3

4

5

6

7

8

9

10

Ready

ADC

ADC 

Confirmation

ADC

Mode Out

Download

Mode In

EDID 

Download

Check EDID 

Status

Define model 

name

Adjustment 

Confirmation

Download 

Mode Out

NO

Item

Remark

CMD1 CMD2

Data 0

a

a

a

a

a

a

a

a

a

a

d

d

d

d

e

e

e

e

e

e

0

0

9

0

0

0~4,9

0~4,9

1~7

9

0

0

1

9

9

0

1

2

5

9

9

Ready

ADC start

Transmitting adjustment mode In

instruction, operate adjustment command.

All=0 ; HDMI1,2,3,4=1,2,3,4 ; RGB=9

All=0 ; HDMI1,2,3,4=1,2,3,4 ; RGB=9

Model define index(Data0) are listed at

next table.

EDID data existence check in SET

assembly