DOWNLOAD LG 50PG6000-ZA (CHASSIS:PD81A) Service Manual ↓ Size: 15.18 MB | Pages: 34 in PDF or view online for FREE

- 4 -

NOTE : Specifications and others are subject to change without notice for improvement.

V

This spec is applied to the 50” 

PLASMA TV used PD81A Chassis.

V 

Each part is tested as below without special appointment.
1) Temperature : 25±5°C (77±9°F), CST : 40±5
2) Relative Humidity: 65±10%
3) Power Voltage: Standard Input voltage (100-240V~, 50/60Hz)

* Standard Voltage of each product is marked by models.

4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with SBOM.
5) The receiver must be operated for about 20 minutes prior to the adjustment.

V

1) Performance : LGE TV test method followed.
2) Demanded other specification 

Safety : CB specification
EMC

: CISPR 13 specification

V

Display Screen Device

Aspect Ratio

PDP Module

Operating Environment

Storage Environment

Input Voltage

1

2

3

4

5

6

No

Item

Specification

Remark

50” Wide Color Display Module

16:9

PDP50G1,

RGB Closed(Well) Type, Glass Filter(38%)

Pixel Format : 1365horiz. By 768 ver.l

1)Temp.

: 0~40deg

2)Humidity : 20~80%

3)Temp.

: -20~60deg

4)Humidity : 10~90%

100-240V~, 50/60Hz

Plasma Display Panel

LGE SPEC.

Maker : LG

Chassis

PD81A

50PG6000

Austria,Belgium,Bulgaria,Coratia,Czech,Denmark,Finland,

France,Germany,Greece,Hungary,Italy,Luxembourg,

Netherlands,Norway,Poland,Portugal,Rumania,Russia,Ser

bia,Slovenia,Spain,Sweden,Switzerland,UK

LG

Model Name

Market

Brand

Remark

50PG6000-ZA

Safety : IEC/EN60065

EMI

: EN55013

EMS

: EN55020

Austria,Belgium,Bulgaria,Coratia,Czech,Denmark,Finlan

d,France,Germany,Greece,Hungary,Italy,Luxembourg,

Netherlands,Norway,Poland,Portugal,Rumania,Russia,

Serbia,Slovenia,Spain,Sweden,Switzerland,UK

Model

Appliance

Market

Remark

- 5 -

V

V

Market

roadcasting system

Receiving system

Scart Jack(2EA)

Video Input (1EA)

S-Video Input (1EA)

Component Input (1EA)

RGB Input

HDMI Input(4EA)

Audio Input (3EA)

SPDIF Out(1EA)

USB

1

2

3

4

5

6

7

8

9

10

11

12

No

Item

Specification

Remark

Austria,Belgium,Bulgaria,Coratia,Czech,Denmark,Finland

,France,Germany,Greece,Hungary,Italy,Luxembourg,

Netherlands,Norway,Poland,Portugal,Rumania,Russia,

Serbia,Slovenia,Spain,Sweden,Switzerland,UK

1) PAL/SECAM BG

2) PAL/SECAM DK

3) PAL I / II

4) SECAM L/L’

5) DVB T

Analog : Upper Heterodyne

Digital : COFDM

PAL, SECAM

PAL, SECAM, NTSC

PAL, SECAM, NTSC

Y/Cb/Cr, Y/Pb/Pr

RGB-PC

HDMI-PC

HDMI-DTV

RGB/DVI Audio, Component, AV

SPDIF OUT

For SVC, S/W Download, X-Studio

25 Country

EU(PAL Marker)

Scart1 Jack is Full scart and support

RF-OUT(Analoge)

Scart2 Jack is Half scart and support

MNT-OUT

Analog(D-Sub 15Pin)

HDMI1/DVI,HDMI2,HDMI3,HDMI4

L/R Input

Side(X-Studio Only PG60 Series)

Display Screen Device

Aspect Ratio

PDP Module

Operating Environment

Storage Environment

Input Voltage

1

2

3

4

5

6

No

Item

Specification

Remark

50” Wide Color Display Module

16:9

PDP50G1,

RGB Closed(Well) Type, Glass Filter(38%)

Pixel Format : 1365horiz. By 768 ver.

1)Temp.

: 0~40deg

2)Humidity : 20~80%

3)Temp.

: -20~60deg

4)Humidity : 10~90%

100-240V~, 50/60Hz

Plasma Display Panel

LGE SPEC.

Maker : LG

- 6 -

These instructions are applied all of the 50” PLASMA TV, 
PD81A

Chassis.

(1) Because this is not a hot chassis, it is not necessary to use

an  isolation  transformer.  However,  the  use  of  isolation
transformer will help protect test instrument.

(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of

25±5°C  of  temperature  and  65±10%  of  relative  humidity  if
there is no specific designation.

(4)  The  input  voltage  of  the  receiver  must  keep  100-240V~,

50/60Hz.

(5) The receiver must be operated for about 15 minutes prior

to the adjustment.

O

After  RGB  Full  white  HEAT-RUN  Mode,  the  receiver  must

be operated prior to adjustment.

O

Enter into HEAT-RUN MODE

1) Press the POWER ON KEY on R/C for adjustment.
2) OSD display and screen display PATTERN MODE.

- Select “3. Test Pattern” by using 

D

/

E

(CH+/-) and

press ENTER(

V

)

- Select “White” by using (

F

/

G

VOL+/-) and press

ENTER(

V

)

* Set is activated HEAT-RUN without signal generator in

this mode.

* Single color pattern(RED/BLUE/GREEN) of HEAT-RUN 

mode uses to check PANEL.

(1) Insert the USB memory sick the PCB ASSEMBLY.
(2) Using ‘power on’ button of the control R/C, power on TV.
(3) S/W download process is executed automatically.

V 

All adjustment process is executed one time through RS-232C.

V 

Command send -> ADC Calibration -> Model name

download -> EDID download.

V

Adjsutment process protocol(RS-232C)

(1) Press ADJ KEY on R/C for model name D/L.
(2) Select “0.Model Option” and press ENTER(

V

).

(3)  Select  model  name  by  using 

D

/

E

(CH+/-)and  press

ENTER(

V

).

* Using ‘power on’ button off the control R/C, power on TV.
All adjustment process is executed one time through RS-232C.
Do not connect extrenal input calbe.

* Using ‘power on’ button of the control R/C, power on TV.
USB file(EPK) version must be bigger than downloaded
version of main B/D.

* Using ‘power on’ button off the control R/C, power on TV.

1

2

3

4

5

6

7

8

9

10

Ready

ADC

ADC 

Confirmation

ADC

Mode Out

Download

Mode In

EDID 

Download

Check EDID 

Status

Define model 

name

Adjustment 

Confirmation

Download 

Mode Out

NO

Item

Remark

CMD1 CMD2

Data 0

a

a

a

a

a

a

a

a

a

a

d

d

d

d

e

e

e

e

e

e

0

0

9

0

0

0~4,9

0~4,9

1~7

9

0

0

1

9

9

0

1

2

5

9

9

Ready

ADC start

Transmitting adjustment mode In

instruction, operate adjustment command.

All=0 ; HDMI1,2,3,4=1,2,3,4 ; RGB=9

All=0 ; HDMI1,2,3,4=1,2,3,4 ; RGB=9

Model define index(Data0) are listed at

next table.

EDID data existence check in SET

assembly

a

e

5

2

50PG6000-ZA

CMD1

CMD2

Data 0

Remark

50PG6000-ZA

36000000

Model Name

Model Option Value

- 7 -

V 

Adjustment is done using internal ADC, so input signal is

not necessary.

V 

Do not connect external input cable.

(1) Press ADJ KEY on R/C and enter EZ ADJUST.
(2) Select  “1.EDID  D/L”  by  using 

D

/

E

(CH+/-)  and  press

ENTER(

V

).

(3) Select “Start” by using 

F

/

G

(VOL+/-) and press ENTER(

V

).

(4) ADC Adjustment is executed automatically.

(1) Press ADJ KEY on R/C and enter EZ ADJUST.
(2)  Select  “5.EDID  D/L”  by  using 

D

/

E

(CH+/-)  and  press

ENTER(

V

).

(3) Select “Start”  and press ENTER(

V

).

(4) EDID download is executed automatically.
(5) Press EXIT key on R/C.

(1) HDMI1(256bytes)

(2) RGB(128bytes)

-> Detail EDID Options are below (

ⓐ, ⓑ, ⓒ, ⓓ, ⓔ)

ⓐ Product ID 

ⓑ Serial No

=> Controlled on production line 

ⓒ Month, Year

=> Controlled on production line:  

ex)  Monthly: ‘11’  ->  ‘0B’ 

Year:  ‘2007’ ->  ‘11’

ⓓ Model Name(Hex)

ⓔ Checksum

=> Changeable by total EDID data.

: You must adjust DTV29 Channel and insert PCMCIA CARD

to socket.

1) If  PCMCIA  CARD  works  normally,  normal  signals  display

on screen. But it works abnormally, “No CA module” words
display on screen.

*Do not connect HDMI and RGB cable.

NO SIGNAL or White noise

NO SIGNAL

RF Input

AV / Component / RGB input

50PG6000-ZA

EDID MODEL

Product ID

FUCTION

Model Name

Analog

Digital

50097(C3B1)

50098(C3B2)

50PG6000-ZA

50PG6000

00 00 00 FC 00 35 30 50 47 36 30 30 30 0A 20 20 20 20

Model Name

Model Name(Hex)

* Set up “RF mode” before launching products.