DOWNLOAD LG 50PC5D-ZB / 50PC5D1-ZD (CHASSIS:PD73A) Service Manual ↓ Size: 52.32 MB | Pages: 53 in PDF or view online for FREE

- 5 -

Market

Broadcasting system

Receiving system

Scart Jack (2EA)

Video Input (1EA)

S-Video Input (1EA)

Component Input (1EA)

RGB Input(1EA)

HDMI Input(2EA)

Audio Input (3EA)

1

2

3

4

5

6

7

8

9

10

No

Item

Specification

Remark

UK, German, Italy, France, Sweden, Finland, Spain

1) PAL-BG

2) PAL-DK

3) PAL-I,I’

4) DVB-T(ID TV)

5) SECAM-L/L’

Analog : Upper Heterodyne

Digital : COFDM

PAL, SECAM

PAL, SECAM, NTSC

PAL, SECAM, NTSC

Y/Cb/Cr, Y/Pb/Pr

RGB-PC

HDMI-DTV & SOUND

PC Audio, Component, AV

4 System : PAL, SECAM, NTSC, PAL60

4 System : PAL, SECAM, NTSC, PAL60

L/R Input

- 6 -

These instructions are applied to all of the 50” PLASMA TV,
PD73A Chassis.

(1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolation
transformer will help protect test instrument.

(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of

25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation.

(4) The input voltage of the receiver must keep 100-240V~,

50/60Hz.

(5) The receiver must be operated for about 15 minutes prior

to the adjustment.

O

After RGB Full white HEAT-RUN Mode, the receiver must

be operated prior to adjustment.

O

Enter into HEAT-RUN MODE

1) Press the POWER ON KEY on R/C for adjustment.
2) OSD display and screen display PATTERN MODE.

[ Set is activated HEAT-RUN without signal generator in

this mode.

[ Single color pattern(RED/BLUE/GREEN) of HEAT-RUN 

mode uses to check PANEL.

: You can set channel memory by R/C for adjustment.

1) Press ADJ key on R/C for adjustment.
2) Press ENTER key on “System Control3”.
3) Press VOL + key on “Channel Recover”.

: You must adjust DTV 29 Channel and insert PCMCIA CARD

to socket.

1) If PCMCIA CARD works normally, normal signals display

on screen.
But it works abnormally, “No CA module” words display on
screen.

(Va, Vs Voltage adjustments)

D.M.M. 1EA

: refer to Fig.1

1) After receiving 100% Full White Pattern, HEAT RUN.
2) Connect + terminal of D.M.M to Va pin of P805, connect

- terminal to GND pin of P805.

3) After turning VR901, voltage of D.M.M adjustment as

same as Va voltage which on label of panel right/top.
(Deviation; ±0.5V)

1) Connect + terminal of D.M.M to Vs pin of P805, connect

– terminal to GND pin of P805.

2) After turning VR951, voltage of D.M.M adjustment as

same as Va voltage which on label of panel right/top.
(Deviation; ±0.5V)

If you turn on a still screen more than 20 minutes (Especially
Digital pattern, Cross Hatch Pattern), an afterimage may occur
in the black level part of the screen.

Each PCB assembly must be checked by check JIG set.
(Because power PCB Assembly damages to PDP Module,
especially be careful)

(Fig. 1) Connection diagram of power adjustment for measuring

<50” 6709900020A>

- 7 -

1) Adjusting PC with S/W for writing EDID Data.(S/W : EDID

TESTER Ver.2.5)

2) A Jig for EDID Download
3) Cable : Serial(9Pin or USB) to D-sub 15Pin cable, D-sub

15Pin cable, DVI to HDMI cable

1) As above Fig. 2, Connect the Set, EDID Download Jig, PC

& Cable.

2) Turn on the PC & EDID Download Jig. And Execute the

S/W : EDID TESTER Ver,2.5.

3) Set up S/W option.

4) Power on the Set.

1) Init the data.

2) Load the EDID data.(Open File).

[Analog file] (for RGB)

[Digital file]  (for HDMI)

3) Set the S/W as below.
4) Push the “Write Data & Verify”button. And confirm “Yes”.
5) If the writing is finished, you will see the “OK” message.
6) If TV has two HDMI, you must download two times for

each HDMI.

1) Analog RGB.

=> Detail EDID Options are below(1, 2, 3, 4, 5)

1. Product ID

2. Serial No :  Controlled on production line
3. Month, Year : Controlled on production line

ex) Week : '03'     =>  '03' 

Year   : '2006' =>  '10'

4. Model Name(Hex): 

5. Checksum  : Changeable by total EDID data

(Fig. 2) Connection Diagram of DDC download

Open File

Open File

Model

Name

XXXX

Product ID

Product ID

EDID table

XXXX

Hex

XX

DEC

XX

XXXXX

Model Name

XXXXX

Hex Data

XXXXX

1

2

3

4

5

- 8 -

2) HDMI.

=> Detail EDID Options are below(a, b, c, d, e)

1. Product ID

2. Serial No :  Controlled on production line
3. Month, Year : Controlled on production line

ex) Week : '03'     =>  '03' 

Year   : '2006' =>  '10'

4. Model Name(Hex): 

5. Checksum  : Changeable by total EDID data

V

This AV color balance adjustment should be performed

before white Balance Adjustment.

1) Remote controller for adjustment.
2) MSPG-925FS Pattern Generator (Which has Video Signal:

7 Color Bar Pattern shown in Fig. 3).
- Model: 202 / Pattern: 65  EC and FC model use PAL-
BGDHI. (composite signal)

1) Input the Video signal: 7 color Bar signal into AV3.
2) Set the PSM to Dynamic mode in the Picture menu.
3) Press IN-STAR key on R/C for adjustment.
4) Press the 

G

(Vol. +) key operate to set, then it becomes

automatically.

5) Auto-RGB OK means completed adjustment.

V

This AV color balance adjustment should be performed

before white Balance Adjustment.

1) Remote controller for adjustment.
2) MSPG-925FS Pattern Generator (Which has Video Signal:

7 Color Bar Pattern shown in Fig. 4).
- Model: 215 / Pattern: 65  

1) Input the Component 720p/50Hz 7 Color Bar(MSPG-925FS

model:215, pattern:65) signal into Component.

2) Set the PSM to Dynamic mode in the Picture menu.
3) Press IN-STAR key on R/C for adjustment.
4) Press the 

G

(Vol. +) key operate to set, then it becomes

automatically.

5) Auto-RGB OK means completed adjustment.

Model

Name

XXXX

Product ID

Product ID

EDID table

XXXX

Hex

XX

DEC

XX

XXXX

Model Name

XXXXX

Hex Data

XXXXX

1

2

3

4

5

5

MSPG925FS

Component

RGB-PC

RF/AV/S-VIDEO

ADC

Model : 3

(1024*768 60Hz)

Pattern : 65

7 Color Bar

Model:215(720P)

Pattern : 65

* 720/50Hz

7 Color Bar

PAL

INPUT SELECT AV3

Model : 202

(PAL-BGDHI)

Pattern : 65

* PAL 7 Color Bar

- System control RS-232 Host should be “PC“ for adjustment.
- Before AV ADC Calibration, execute the “Panel size selection“

(Fig. 4) Color bar Test Pattern

(Fig. 3) Color Balance signal