LG 50PB4RT-TB (CHASSIS:PP7BA) Service Manual ▷ View online
- 9 -
9. Adjustment of Component
9-1. Required Equipment
(1) Remote controller for adjustment.
(2) 802F Pattern Generator, Master(MSPG-925FA), etc.
(3) MSPG-925FA Pattern Generator.
(2) 802F Pattern Generator, Master(MSPG-925FA), etc.
(3) MSPG-925FA Pattern Generator.
(Which has 720P@60Hz YPbPr Signal : 100% Color Bar
Pattern shown in Fig.4)
-> Model : 217 / Pattern : 65
(4) It is very import to use correct adjustment pattern like
Fig.4.
1) Within the pattern, color sequence should be aligned
1) Within the pattern, color sequence should be aligned
: White-Yellow-Cyan-Green-Gray-Red-BLUE-BLACK
( If color sequence is reversed (Black -> ...-> White),
reverse the pattern with REV key, when using Master
pattern generator like MSPG-925)
pattern generator like MSPG-925)
2) If Minimum Black Level and/or Maximum White Level is
not correct, Do select 100% Color Bar Pattern.
9-2. Method of Auto Component Color Balance
(1) Input the Component 720p 100% Color Bar(MSPG-925FA
model:217, pattern:65) signal into Component.
(2) Set the PSM to Dynamic mode in the Picture menu.
(3) Press the INSTART key on R/C for adjustment.
(4) Press the
(3) Press the INSTART key on R/C for adjustment.
(4) Press the
G
(Vol.+) key to operate the set , then it
becomes automatically.
(5) Auto-RGB OK means the adjustment is completed.
10. Adjustment of RGB
10-1. Required Equipment
(1) Remote controller for adjustment.
(2) 802F Pattern Generator, Master(MSPG-925FA), etc.
(3) MSPG-925FA Pattern Generator.
(2) 802F Pattern Generator, Master(MSPG-925FA), etc.
(3) MSPG-925FA Pattern Generator.
(Which has XGA [1024*768] 60Hz PC Format output signal :
100% Color Bar Pattern shown in Fig.5)
(4) It is very import to use correct adjustment pattern like
Fig.5.
1) Within the pattern, color sequence should be aligned
1) Within the pattern, color sequence should be aligned
: White-Yellow-Cyan-Green-Gray-Red-BLUE-BLACK
( If color sequence is reversed (Black -> ...-> White),
reverse the pattern with REV key, when using Master
pattern generator like MSPG-925)
pattern generator like MSPG-925)
2) If Minimum Black Level and/or Maximum White Level is
not correct, Do select 100% Color Bar Pattern.
10-2. Method of Auto RBG Color Balance
(1) Input the Component 720p 100% Color Bar(MSPG-925FA
model:217, pattern:65) signal into Component.
(2) Set the PSM to Dynamic mode in the Picture menu.
(3) Press the INSTART key on R/C for adjustment.
(4) Press the
(3) Press the INSTART key on R/C for adjustment.
(4) Press the
G
(Vol.+) key to operate the set , then it
becomes automatically.
(5) Auto-RGB OK means the adjustment is completed.
(Fig. 4)
(Fig. 4)
- 10 -
11. White Balance
* Notice
- Do the white balance adjustment under the 10LUX
- Before white balance, press the In-start key 2times and do
the reset like Fig.6
- Use the Torino inner pattern(216 gray pattern)
- To enter White-balance mode,press the IN-START key
2times.
11-1. Test Equipment
(1) Color Analyzer (CA-100),CA-210.
* Note : When using the Color Analyzer with PDP,
* Note : When using the Color Analyzer with PDP,
recommend the CA-100 more than CA-210.
If CA-100 can not available, it is also good th use
the CA-210
If CA-100 can not available, it is also good th use
the CA-210
(2) PC(for communication through RS-232C)
-> UART Baud rate : 115200.
(3) Pattern Generator(MSPG-925FA etc.)
11-2. Color Temperature & Color
Coordinates Setting
(1) When adjusting the Color Temperature of PDP, Color
Analyzer CA-210(Matrix should be corrected through
CH10 of CS-1000) should be used. When CA-210 have
used, it don’t need to fit the CH10.
CH10 of CS-1000) should be used. When CA-210 have
used, it don’t need to fit the CH10.
(2) Adjust the Color Temperature based below adjustment
color coordinates.
(3) Even if CH9 of CA-210 is corrected with Matrix, there may
be many character of Module and Filter.
(4) Therefore Refer to the below Color Coordinates Target.
But, in case of WCG module, use the CH12 of CA-210.
W
Target Value CA-210(CH10), CA-100
( R/G/B gain and R/G/B offset Default values are different in
according to using module)
W
Target Value of Brightness, Color Coordinates, Color Temperature
11-3 .Manual white Balance (INNER Pattern)
(For White Balance, Adjust twice, Cool and Warm)
(1) Execute CA-100, CA-210(10CH) or CA-100 Zero Calibration.
(2) Use torino inner pattern as below Fig.7, Supply 216Level
(2) Use torino inner pattern as below Fig.7, Supply 216Level
(85 IRE) full screen pattern
(3) Enter the White Balance adjustment mode by pressing the
INSTART key twice(White Balance) on R/C.
(4) Stick sensor to center of the screen and select each items
(Red/Green/Blue Gain and Offset) using
D
/
E
(CH+/-) key
on R/C.
(5) Adjust with R / G / B Gain using
F
/
G
(VOL+/-) key on R/C.
(6) Adjust it until color coordination becomes as below.
W
Color Temperature : Cool, Medium, Warm
(1) One of R/G.B Gain should be fixed at 80 and adjust two
Gain Value with decreasing the Default values from 80
1) When R Gain is Fixed at Default value(80)
- Adjust G gain and B gain with decreasing Default values
from 80
2) When B Gain is Fixed at Default value(80)
- Adjust R gain and G gain with decreasing Default values
from 80
3) When G Gain is Fixed at Default value(80)
- Adjust R gain and B gain with decreasing Default values
from 80
(2) R/G/B Gain and R/G/B Offset Default Value.
- Red Gain : 80
- Green Gain : 80
- Blue Gain : 80
(Fig.6)
80
80
80
80
80
7D
80
80
7D
80
80
8C
8C
- Before White-balance, the AV ADC should be done.
- System control RS-232 Host should be “PC“ for adjustment.
- After All adjustment is completed, Please push “Instop” Key.
Temp
x
0.276±0.002
0.313±0.002
0.283±0.002
0.329±0.002
+0.000
+0.003
11,000K
6,500K
COOL
WARM
CSM
y
uv
High Light
High Light
60 ± 20cd/m2(42XGA)
Cool
X: 0.276±0.002, Y: 0.283±0.002
Normal
X: 0.313±0.002, Y: 0.329±0.002
Cool
11,000±500K
Warm
6,500K±500K
Brightness
Color
-Coordinate
Desired result (216 Gray)
(Fig.7)
Color Temperature
High Light
High Light
50 ± 20cd/m2(80% of non-high altitude)
Cool
X: 0.276±0.002, Y: 0.283±0.002
Normal
X: 0.313±0.002, Y: 0.329±0.002
Cool
11,000±500K
Warm
6,500K±500K
Brightness
Color
-Coordinate
Desired result for high altitude(216 Gray)
Color Temperature
- 11 -
11-4 .Auto white Balance (INNER Pattern)
Input Select
R-Gain_Normal
G-Gain_Normal
B-Gain_Normal
R-Gain_Warm
G-Gain_Warm
B-Gain_Warm
R-Gain_Cool
G-Gain_Cool
B-Gain_Cool
R-Offset_Normal
G-Offset_Normal
B-Offset_Normal
R-Offset_Warm
G-Offset_Warm
B-Offset_Warm
R-Offset_Cool
G-Offset_Cool
B-Offset_Cool
COLOR TEMP.
Inner Pattern Signal
x
j
j
j
j
j
j
j
j
j
l
l
l
l
l
l
l
l
l
k
w
b
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
u
b
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00h
01h
10h
11h
20h
21h
40h
41h
60h
90h
Min
00h
00h
00h
00h
00h
00h
00h
00h
00h
00h
00h
00h
00h
00h
00h
00h
00h
00h
00h
00
10
ff
Max
80h
80h
80h
80h
80h
80h
80h
80h
80h
80h
80h
80h
80h
80h
80h
80h
80h
80h
03h(Cool,Normal,Warm,User)
W/B Adjustment Start
Adjustment Completion
DTV-Air
Cable
RF-Air
Cable
AV1
AV2
COMP1
COMP1
RGB-PC
HDMI
INIT
80h
80h
80h
80h
80h
80h
80h
80h
80h
No
Command1
Command2
Set ID
Data
Mode
- 12 -
W
Input Select Data
: RF(10), AV1~4(20,21,22,23), SAV(30), COMP(40), DVI(50 or 60), HDMI(90)
W
Command Set
( SET ID : 0 -> ALL, 1~99 -> each SET )
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
POWER ON/OFF
MAIN INPUT
ARC
SCREEN MUTE
AUDIO MUTE
VOLUME
CONTRAST
BRIGHTNESS
COLOR
TINT
SHARPNESS
OSD ON/OFF
CHILD LOCK
PIP MODE
PIP ARC
PIP POSITION
TREBLE
BASS
BALANCE
COLOR TEMP.
RED LEVEL
GREEN LEVEL
BLUE LEVEL
PIP INPUT
CURRENT STATE
KA(ka)
XB(xb)
KC(kc)
KD(kd)
KE(ke)
KF(kf)
KG(kg)
KH(kh)
KI(ki)
KJ(kj)
KK(kk)
KL(kl)
KM(km)
KN(kn)
KO(ko)
KQ(kq)
KR(kr)
KS(ks)
KT(kt)
KU(ku)
KV(kv)
KW(kw)
K$(k$)
XY(xy)
KZ(kz)
0~99
0~99
0~99
0~99
0~99
0~99
0~99
0~99
0~99
0~99
0~99
0~99
0~99
0~99
0~99
0~99
0~99
0~99
0~99
0~99
0~99
0~99
0~99
0~1
10~90
1~8
0~1
0~1
0~64
0~64
0~64
0~64
0~64
0~64
0~1
0~1
0~3
0~64
0~64
0~64
0~3
0~50
0~50
0~50
10~90
FF
0: OFF, 1:ON
RF(10), AV1~4(20,21,22,23),
SAV(30), COMP(40),
RGB(50 or 60), HDMI(90)
4:3; 16:9; SPECTACLE; ZOOM;
ORIGINAL; 14:9; FULL
1: MUTE, 0: MUTE OFF
1: MUTE, 0: MUTE OFF
0: 0, 64 : 100 (Hexadecimal)
0: 0 , 64 : 100 (Hexadecimal)
0: 0 , 64 : 100 (Hexadecimal)
0: 0 , 64 : 100 (Hexadecimal)
0: R50 , 64 : G50 (Hexadecimal)
0: 0 , 64 : 100 (Hexadecimal)
0: OFF, 1: ON
1: LOCK, 0: OFF
PIP_OFF, PIP, DW1, DW2
NOT USED
NOT USED
0:0 , 64:100
0:0 , 64:100
0:L50, 64:R50
COOL, NORMAL, WARM, USER
0 : -40, 50 : 40
0 : -40, 50 : 40
0 : -40, 50 : 40
RF(10), AV1~4(20,21,22,23),
SAV(30), COMP(40),
DVI(50 or 60), ,HDMI(90)
ACK is 0, there is Signal
ACK is 1, there is No Signal
ACK is 2, power Off Status
No
Adjustment contents
CMD
SET ID
VAL
Specification
Click on the first or last page to see other 50PB4RT-TB (CHASSIS:PP7BA) service manuals if exist.