DOWNLOAD LG 50PB2RRH-TL (CHASSIS:MF-056L) Service Manual ↓ Size: 15.69 MB | Pages: 55 in PDF or view online for FREE

- 9 -

O 

This  AV  color  balance  adjustment  should  be  performed

before White Balance Adjustment.

O 

It is very import to use correct adjustment pattern like (Fig.5).

A 

Within  the  pattern,  color  sequence  should  be  aligned  :

W-Y-C-G-M-R-BLUE-BLACK.
(If  color  sequence  is  reversed  (Black  ->...->  White),
reverse  the  pattern  with  REV  key,  when  using  Master
pattern generator like MSPG-925)

A 

If Minimum Black Level and/or Maximum White Level is

not correct, Do select 100% Color Bar Pattern.

1) Remote controller for adjustment
2)  AV  Pattern  Generator  :  802F  Pattern  Generator,

Master(MSPG-925FA), etc.
(Which  has  PAL  Composite  Video  format  output  with
standard(1.0 Vpp) Vertical 100% Color Bar Pattern as Fig. 5)

1)  Input  the  PAL  Composite  Video  (Fig.5.  100%  Color  Bar

Pattern) into video input. ( 42/50PC1RR-CL : AV2 )

2) Set the PSM to Dynamic mode in Picture menu.
3) Press IN-START key on R/C for adjustment.
4) Press the 

G 

(Vol.+) key operate to set , then it becomes

automatically.

5) Auto-RGB OK means completed adjustment.

O 

It is very import to use correct adjustment pattern like (Fig.6).

A 

Within  the  pattern,  color  sequence  should  be  aligned  :

W-Y-C-G-M-R-BLUE-BLACK.
(If  color  sequence  is  reversed  (Black  ->...->  White),
reverse  the  pattern  with  REV  key,  when  using  Master
pattern generator like MSPG-925)

A 

If Minimum Black Level and/or Maximum White Level is

not correct, Do select 100% Color Bar Pattern.

1) Remote controller for adjustment.
2) 802F Pattern Generator.

( Which has 720p YpbPr output with Standard(0.7Vpp)Vertical
100% Color Bar Pattern as Fig. 6 )

1) Input the Component 720p 100% Color Bar signal into

Component1.

2) Set the PSM to Dynamic mode in Picture menu.
3) Press IN-START key on R/C for adjustment. 

4) Press the 

G

(Vol.+) key operate To set , then it becomes

automatically.

5) Auto-RGB OK means completed adjustment.

O 

It is very import to use correct adjustment pattern like (Fig. 7).

A 

Within  the  pattern,  color  sequence  should  be  aligned  :

W-Y-C-G-M-R-BLUE-BLACK.
(If  color  sequence  is  reversed  (Black  ->...->  White),
reverse  the  pattern  with  REV  key,  when  using  Master
pattern generator like MSPG-925)

A 

If Minimum Black Level and/or Maximum White Level is

not correct, Do select 100% Color Bar Pattern.

1) Remote controller for adjustment
2) 802F Pattern Generator, Master (MSPG-925FA), etc.

(  Which  has  XGA  60Hz  PC  Format  output  with
standard(0.7Vpp) 100 % Color Bar Pattern as Fig. 7 )

1) Input the PC 1024x768 @ 60Hz 100 % Color Bar Pattern

into RGB.

2) Set the PSM to Dynamic mode in Picture menu.
3) Press IN-START key on R/C for adjustment. 
4) Press the 

G 

(Vol.+) key operate To set , then it becomes

automatically.

5) Auto-RGB OK means completed adjustment.

O 

It is very import to use correct adjustment pattern like (Fig. 8).

A 

Within  the  pattern,  color  sequence  should  be  aligned  :

W-Y-C-G-M-R-BLUE-BLACK.
(If  color  sequence  is  reversed  (Black  ->...->  White),
reverse  the  pattern  with  REV  key,  when  using  Master
pattern generator like MSPG-925)

A 

If Minimum Black Level and/or Maximum White Level is

not correct, Do select 100% Color Bar Pattern.

(Fig. 5) Auto AV(CVBS) Color Balance Test Pattern

(Fig. 6) Auto Component Color Balance Test Pattern

(Fig. 7) Auto RGB Color Balance Test Pattern

- 10 -

1) Remote controller for adjustment
2) 802F Pattern Generator, Master (MSPG-925FA), etc.

( Which has 576i YpbPr output with Standard(0.7Vpp)Vertical
100% Color Bar Pattern as Fig.8)

1) Input the Component 576i 100% Color Bar signal into

Component1.

2) Set the PSM to Dynamic mode in Picture menu.
3) Press IN-START and then TURBO-PICTURE key on R/C

for adjustment. 

4) Press the 

G

(Vol.+) key operate To set , then it becomes

automatically.

5) Auto-RGB OK means completed adjustment.
6) If the result is “NG’, Try once more.

1) Press ‘OK’ button and check Time Shift is working through

Progress bar is on.

2) Press         after the time is 0:00:02 on the bar and check

previous picture for a few seconds.
( just         ,        is working under 30seconds)

3) Press         and check a live picture back.

1) Time setting : 

(1) Set any time on the MENU for recoding.

(Recoding can’t be done under the Time is not active. 

When main power is off , the time will be resetted.)

2) Manual Recoding : 

(1) Set recoding information and check it on the scheduled

list.

3)  Instant Recoding.

(1) Press the recoding button on remote control and record

a present program for 10 seconds then press the stop
button to stop recoding.

(2) After finishing recoding, play the recoded clip on ’the

Recoded TV’. 

(Fig. 8) Auto DVR Color Balance Test Pattern

(Fig. 9) DVR MENU

(Fig. 10) Time Shift Progress bar

(Fig. 11) DVR MENU

(Fig. 12) Scheduled List

(Fig. 13) Xstudio PRO MENU

(Fig. 14) Recoded List

- 11 -

(Va, Vs Voltage adjustments)

D.M.M. 1EA

: refer to Fig.15

1) After receiving 100% Full White Pattern, HEAT RUN.
2) Connect + terminal of D. M..M. to Va pin of P805, connect

-terminal to GND pin of P805.

3)  After  turning  VR901,voltage  of  D.M.M  adjustment  as

same  as  Va  voltage  which  on  label  of  panel  right/top.
(deviation; 

±0.5V)

1) Connect + terminal of D. M..M. to Vs pin of P805, connect

-terminal to GND pin of P805.

2)  After  turning  VR951,  voltage  of  D.M.M  adjustment  as

same  as  Vs  voltage  which  on  label  of  panel  right/top.
(deviation ; 

±0.5V)

1) Adjusting PC with S/W for writing EDID Data.

(S/W : EDID TESTER Ver.2.5)

2) A Jig for EDID Download.
3)  Cable  :  Serial(9Pin  or  USB)  to  D-sub  15Pin  cable,  D-sub

15Pin cable, DVI to HDMI cable.

1) As above Fig. 16, Connect the Set, EDID Download Jig, PC

& Cable.

2)  Turn  on  the  PC  &  EDID  Download  Jig.  And  Execute  the

S/W : EDID TESTER Ver,2.5.

3) Set up S/W option.

4) Power on the Set.

1) Init the data.

2) Load the EDID data.(Open File).

[Analog(RGB) :
50PC1RR_RGB(B4)0307.ana] (VGA,XGA)
[Digital(HDMI):
50PC1RR_HDMI(DC37)_0307.div] (XGA)

3) Set the S/W as below.
4) Push the “Write Data & Verify”button. And confirm “Yes”.
5) If the writing is finished, you will see the “OK” message.

(Fig. 15) Connection Diagram of power adjustment for measuring.

(Fig. 16) Connection Diagram of DDC download

Open File

Open File

- 12 -

6) HDMI/DVI EDID data(check sum : DC37)

7) RGB EDID data(check sum : B4)

1) Remote controller for adjustment.
2) Color Analyzer.(CA-100 or same product)
3) Auto W/B adjustment instrument.(only for Auto adjustment)
4) AV Pattern Generator.

W

Auto adjustment Map(RS-232C)

(For Manual adjustment)

O

Operate  the  zero-calibration  of  the  CA-100,  then  stick

sensor to PDP module surface when you adjust.

O

For  manual  adjustment,  it  is  also  possible  by  the  following

sequence.

1)  Select  white  pattern  of  heat-run  mode  by  pressing  power

on key on remote control for adjustment then operate heat
run more than 15 minutes.

2)  As  below  Fig.18,  Supply  216Level  (85  IRE)  full  screen

pattern to Video input.

(50PB2RR-TL : AV1/AV2, Press the Front AV key->AV2) 

3) Press the TV/AV KEY on R/C for converting input mode.
4) Set the PSM to Standard mode in Picture menu.
5) Enter the White Balance adjustment mode by pressing the

IN-START key twice(White Balance) on R/C.

6) Stick sensor to center of the screen and select each items

(Red/Green/Blue Gain and Offset) using 

D

/

E

(CH +/-) key on R/C.

7)  Adjust  Only  High  Light  with  R  Gain/  B  Gain  using 

F

/

G

(VOL+/-) key on R/C.

8) Adjust it until color coordination becomes as below.

(Initially, R/G/B gain and R/G/B offset values are fixed as below
Red Gain   : 82,

Green Gain   : 80,

Blue Gain   : 86

Red Offset : 7F,

Green Offset : 7E,

Blue Offset : 82)

9)  When  adjustment  is  completed,  Exit  adjustment  mode

using EXIT key on R/C.

M SPG-

M STG- 5 2 0 0

216 Level (85 IRE)

216 Level (85 IRE)

COLOR 

COLOR ANAL

ANALYZER

YZER

TYPE ; CA-100

TYPE ; CA-100

CVBS

CVBS
signal

signal
input

input

RS-232C Serial Communication

925

Pattern Generator

Pattern Generator

/

(Fig. 17) Connection Diagram of Auto W/B Adjustment

Type

Baud Rate

115200

Index

R Gain

G Gain

B Gain

R Offset

G Offset

B Offset

Data bit

8

Cmd1 Cmd2

j

a

j

b

j

c

j

d

j

e

j

f

Stop bit

1

Parity

NONE

MF-056L

Protocol

Setting

Data

Min Value

00(00)

00(00)

00(00)

00(00)

00(00)

00(00)

Max Value

255(FF)

255(FF)

255(FF)

255(FF)

255(FF)

255(FF)

(Fig. 18) Pattern for Adjustment of White Balance

216 Level (85 IRE)

216 Level (85 IRE)